101606-1350 ZEXEL 9 400 615 441 BOSCH INJECTION-PUMP ASSEMBLY 9400615441 1016061350 me056644


101606-1350 INJECTION-PUMP ASSEMBLY
Rating:
24
Buy INJECTION-PUMP ASSEMBLY 101606-1350 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

BOSCH 9 400 615 441 9400615441
ZEXEL 101606-1350 1016061350
MITSUBISHI ME056644 me056644

Include in #2:

Cross reference number

BOSCH 9 400 615 441 9400615441
ZEXEL 101606-1350 1016061350
MITSUBISHI ME056644 me056644


Zexel num
Bosch num
Firm num
Name
101606-1350 
101606-6610 
9 400 615 441 
ME056644  MITSUBISHI
INJECTION-PUMP ASSEMBLY
6D22 * K

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil
  ISO4113 or {SAEJ967d}
Test oil temperature degC   40 40 45
Nozzle and nozzle holder   105780-8140
Bosch type code   EF8511/9A
Nozzle   105780-0000
Bosch type code   DN12SD12T
Nozzle holder   105780-2080
Bosch type code   EF8511/9
Opening pressure MPa   17.2
Opening pressure kgf/cm2   175
Injection pipe
Outer diameter - inner diameter - length (mm)
mm   6-2-600
Overflow valve   131424-5120
Overflow valve opening pressure kPa   255 221 289
Overflow valve opening pressure kgf/cm2   2.6 2.25 2.95
Tester oil delivery pressure kPa   157 157 157
Tester oil delivery pressure kgf/cm2   1.6 1.6 1.6
Direction of rotation (viewed from drive side)
Right
  R
Injection timing adjustment
Direction of rotation (viewed from drive side)
Right
  R
Injection order   1-5-3-6- 2-4
Pre-stroke mm   4.5 4.45 4.55
Beginning of injection position
Governor side
  NO.1
Difference between angles 1
Cal 1-5
deg.   60 59.5 60.5
Difference between angles 2
Cal 1-3
deg.   120 119.5 120.5
Difference between angles 3
Cal 1-6
deg.   180 179.5 180.5
Difference between angles 4
Cyl.1-2
deg.   240 239.5 240.5
Difference between angles 5
Cal 1-4
deg.   300 299.5 300.5
Injection quantity adjustment
Adjusting point   -
Rack position   9.9
Pump speed r/min   700 700 700
Each cylinder's injection qty mm3/st.   120 116.6 123.4
Basic   *
Fixing the rack   *
Standard for adjustment of the maximum variation between cylinders   *
Injection quantity adjustment_02
Adjusting point   C
Rack position   8+-0.5
Pump speed r/min   225 225 225
Each cylinder's injection qty mm3/st.   18.5 15.7 21.3
Fixing the rack   *
Standard for adjustment of the maximum variation between cylinders   *
Injection quantity adjustment_03
Adjusting point   A
Rack position   R1(9.9)
Pump speed r/min   700 700 700
Average injection quantity mm3/st.   120 119 121
Basic   *
Fixing the lever   *
Injection quantity adjustment_04
Adjusting point   B
Rack position   R1(9.9)
Pump speed r/min   1100 1100 1100
Average injection quantity mm3/st.   123.7 121.2 126.2
Difference in delivery mm3/st.   9 9 9
Fixing the lever   *
Injection quantity adjustment_05
Adjusting point   E
Rack position   -
Pump speed r/min   100 100 100
Average injection quantity mm3/st.   140 100 180
Fixing the lever   *
Remarks
After startup boost setting
 
Timer adjustment
Pump speed r/min   850--
Advance angle deg.   0 0 0
Remarks
Start
 
Timer adjustment_02
Pump speed r/min   800
Advance angle deg.   0.5
Timer adjustment_03
Pump speed r/min   1000
Advance angle deg.   0.9 0.4 1.4
Timer adjustment_04
Pump speed r/min   1150
Advance angle deg.   3 2.5 3.5
Timer adjustment_05
Pump speed r/min   -
Advance angle deg.   4 4 5
Remarks
Measure the actual speed, stop
 

Test data Ex:

Governor adjustment

Test data 101606-1350
N:Pump speed R:Rack position (mm) (1)Excess fuel setting for starting: SXL (2)Damper spring setting: DL (3)When air cylinder is operating.
----------
SXL=R1(9.9)+0.2mm DL=6.8-0.2mm
----------

Speed control lever angle

Test data 101606-1350
F:Full speed (1)Set the pump speed at aa (2)Set the pump speed at bb.
----------
aa=1150r/min bb=(480)r/min
----------
a=10deg+-5deg b=(15deg)+-5deg

0000000901

Test data 101606-1350
F:Full load I:Idle (1)Stopper bolt setting
----------

----------
a=21deg+-5deg b=30deg+-3deg

Stop lever angle

Test data 101606-1350
N:Pump normal S:Stop the pump. (1)Free (at shipping) (2)Rack position = aa (3)Rack position bb (4)Stopper bolt setting
----------
aa=13.5mm bb=6-0.5mm
----------
a=(58deg) b=36deg+5deg-7deg c=24deg+-5deg

0000001501 MICRO SWITCH

Adjustment of the micro-switch Adjust the bolt to obtain the following lever position when the micro-switch is ON. (1)Speed N1 (2)Rack position Ra
----------
N1=325+-5r/min Ra=7.3mm
----------

0000001601 ACS

Test data 101606-1350
Aneroid compensator adjustment (1)Adjust the clearance between the aneroid compensator's main body and the push rod to L1. (2)Pump speed N1 at load lever's full position. (3)Screw in the aneroid compensator body to obtain the performance shown in the graph above.
----------
L1=0.1~0.5mm N1=700r/min
----------
Ra=9.9mm Rb=(9.2)mm P1=(88.6)kPa((665)mmHg) P2=69+-0.7kPa(518+-5mmHg) Q1=120+-1cm3/1000st Q2=100.5+-1cm3/1000st

0000001701 2-STAGE CHANGEOVER DEVICE

Test data 101606-1350
RFD governor 2 stage changeover mechanism adjustment outline (A) Bolt (B) bolt (c) Nut (D) Return spring (E) Bolt (F) Bolt (G) Screw (H) Bolt (I) Load lever (J) Speed lever (K) Air cylinder (M Air inlet Figure 1 is only for reference. Lever shape, etc, may vary. 1. Minimum-maximum speed specification adjustment (when running) (a) Without applying air to the air cylinder, loosen bolts (A) and (B). (1)High speed return L setting (a) In the speed range Nf~Nf - 300r/min, adjust using the speed adjusting bolt to determine the temporary beginning of high speed control speed. (b) Determine the rack position in the vicinity of Rf using the full load lever. (c) Increase speed and confirm return distance L. (d) Adjust using the tension lever bolt to obtain L. (2)Setting full load rack position Rf (a) Move the load control lever to the full side. (b) Adjust the full load adjusting bolt so that Rf can be obtained, then fix. (3)Setting the beginning of high speed operation Nf (a) Adjust using bolt (E) so that Nf can be obtained, and then fix. (4)Idle control setting (Re, Ni, Rc) (a) Set the speed at Ns + 200r/min and move the load control lever to the idle side. (b) Fix the lever in the position where Re can be obtained. (c) Next, decrease speed to Ni and screw in the idle spring. (d) Adjust to obtain rack position Ri. (e) Increase the speed and after confirming that the rack position is Re at Ns, set the speed at 0. (f) Confirm protrusion position Rc at idle. (5)Damper spring adjustment (a) Increase speed and set the speed at the rack position Rd - 0.1 mm (b) Set using the damper spring so that the rack position Rd can be obtained. (c) When Rd is not specified, Rd = Ri - 0.5 mm. (6)High speed droop confirmation (a) Return the load control lever to the full load lever position. (b) Increase the speed and confirm that Rf can be obtained at Nf r/min. (c) Confirm that speed is Nh at rack position Rh. 2. Variable speed specification adjustment (at operation) (a) Remove return spring (D). (b) Apply air pressure of 245~294 kPa {2.5~3 kg/cm2} to the air cylinder. (c) Perform the following adjustment in this condition. (1)Setting full load rack position Rf' (a) Pull the load lever to the idle side. (b) Obtain rack position Rf' using the nut (C). (Pump speed is Nf'-50 r/min.) (2)Setting full speed Nf' (a) Adjust using bolt (B) so that Nf can be obtained, and then fix. (3)Low speed side setting (a) At 350r/min, set bolt (F) at beginning of governor operation position, then fix. 3. Bolt (A) adjustment (1)Install return spring (D) and perform the adjustments below at air pressure 0. (a) Set at speed Nf using bolt (E). (b) Screw in bolt (A). (c) Screw in 1 more turn from the speed lever contact position (d) Fix bolt (A). (e) At this time confirm that the air cylinder's shaft moves approximately 1 mm towards the governor. 4. Lever operation confirmation using the air cylinder (1)Apply 588 kPa {6 kg/cm2} air pressure to the air cylinder. (2)Confirm that the cylinder piston is moved 50 mm by the spring (D).
----------

----------

Timing setting

Test data 101606-1350
(1)Pump vertical direction (2)Coupling's key groove position at No 1 cylinder's beginning of injection (3)- (4)-
----------

----------
a=(7deg)




Have questions with 101606-1350?





Group cross 101606-1350 ZEXEL

Mitsubishi 

 
 
INJECTION-PUMP ASSEMBLY
6D16
9 400 615 436 
ME047487 
INJECTION-PUMP ASSEMBLY
6D16
 
ME444571 
INJECTION-PUMP ASSEMBLY
6D16
9 400 615 437 
ME056669 
INJECTION-PUMP ASSEMBLY
6D22
9 400 615 438 
ME056641 
INJECTION-PUMP ASSEMBLY
6D22
9 400 615 439 
ME056642 
INJECTION-PUMP ASSEMBLY
6D22
9 400 615 440 
ME056643 
INJECTION-PUMP ASSEMBLY
6D22
101606-1350  

101606-6610 
9 400 615 441 
ME056644 
INJECTION-PUMP ASSEMBLY
6D22
9 400 615 442 
ME056646 
INJECTION-PUMP ASSEMBLY
6D22
9 400 615 443 
ME056647 
INJECTION-PUMP ASSEMBLY
6D22
9 400 615 444 
ME056648 
INJECTION-PUMP ASSEMBLY
6D22
9 400 615 445 
ME056650 
INJECTION-PUMP ASSEMBLY
6D22
Back to top