101402-4150 ZEXEL F 019 Z10 324 BOSCH INJECTION-PUMP ASSEMBLY f019z10324 1014024150 8970314860


101402-4150 INJECTION-PUMP ASSEMBLY
Rating:
49
Buy INJECTION-PUMP ASSEMBLY 101402-4150 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

BOSCH F 019 Z10 324 f019z10324
ZEXEL 101402-4150 1014024150
ISUZU 8970314860 8970314860

Service parts 101402-4150 INJECTION-PUMP ASSEMBLY:

1. _
2. FUEL INJECTION PUMP 101040-8880
3. GOVERNOR 105419-0570
4. SUPPLY PUMP 105220-5940
5. AUTOM. ADVANCE MECHANIS
6. COUPLING PLATE
7. COUPLING PLATE 156637-1521
8. _
9. _
10. NOZZLE AND HOLDER ASSY 105101-6311
11. Nozzle and Holder 8-97016-146-1
12. Open Pre:MPa(Kqf/cm2) 18.1{185}
13. NOZZLE-HOLDER 105030-4361
14. NOZZLE 105015-8690
15. NOZZLE SET

Include in #1:

101402-4150 as INJECTION-PUMP ASSEMBLY

Cross reference number

BOSCH F 019 Z10 324 f019z10324
ZEXEL 101402-4150 1014024150
ISUZU 8970314860 8970314860


Zexel num
Bosch num
Firm num
Name
101402-4150 
101402-4151 
F 019 Z10 324 
8970314860  ISUZU
INJECTION-PUMP ASSEMBLY
4BD1-T * K

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil
  ISO4113 or {SAEJ967d}
Test oil temperature degC   40 40 45
Nozzle and nozzle holder   105780-8140
Bosch type code   EF8511/9A
Nozzle   105780-0000
Bosch type code   DN12SD12T
Nozzle holder   105780-2080
Bosch type code   EF8511/9
Opening pressure MPa   17.2
Opening pressure kgf/cm2   175
Injection pipe
Outer diameter - inner diameter - length (mm)
mm   6-2-600
Overflow valve   131424-4920
Overflow valve opening pressure kPa   127 107 147
Overflow valve opening pressure kgf/cm2   1.3 1.1 1.5
Tester oil delivery pressure kPa   157 157 157
Tester oil delivery pressure kgf/cm2   1.6 1.6 1.6
Direction of rotation (viewed from drive side)
Right
  R
Injection timing adjustment
Direction of rotation (viewed from drive side)
Right
  R
Injection order   1-3-4-2
Pre-stroke mm   3.4 3.35 3.45
Beginning of injection position
Drive side
  NO.1
Difference between angles 1
Cal 1-3
deg.   90 89.5 90.5
Difference between angles 2
Cal 1-4
deg.   180 179.5 180.5
Difference between angles 3
Cyl.1-2
deg.   270 269.5 270.5
Injection quantity adjustment
Adjusting point   A
Rack position   9.9
Pump speed r/min   1250 1250 1250
Average injection quantity mm3/st.   87.7 86.6 88.8
Max. variation between cylinders %   0 -2 2
Basic   *
Fixing the lever   *
Injection quantity adjustment_02
Adjusting point   C
Rack position   10.4
Pump speed r/min   500 500 500
Average injection quantity mm3/st.   79.8 77.8 81.8
Max. variation between cylinders %   0 -4 4
Fixing the lever   *
Injection quantity adjustment_03
Adjusting point   -
Rack position   6.7+-0.5
Pump speed r/min   440 440 440
Average injection quantity mm3/st.   8.8 7.4 10.2
Max. variation between cylinders %   0 -14 14
Fixing the rack   *
Remarks
Adjust only variation between cylinders; adjust governor according to governor specifications.
 

Test data Ex:

Governor adjustment

Test data 101402-4150
N:Pump speed R:Rack position (mm) (1)Target notch: K (2)Set idle sub-spring (3)Main spring setting
----------
K=8
----------

Speed control lever angle

Test data 101402-4150
F:Full speed I:Idle S:Stop D:Dead point
----------

----------
a=(24deg)+-5deg b=(15deg)+-5deg c=(17deg)+-5deg d=13deg+-3deg

Stop lever angle

Test data 101402-4150
N:Pump normal S:Stop the pump.
----------

----------
a=6deg+-5deg b=46deg+-5deg

0000001501 LEVER

Test data 101402-4150
1. Variable lever adjustment (1)Fix lever B in the idle position using the bolts C and D. (2)Temporarily fix lever A in center of long hole. (3)Set the dead point position temporarily and measure the lever angle. (4)After idle adjustment, loosen the full side stopper bolt D. (5)Move lever A in full speed direction. (6)Fix the bolt D at the full speed position. (7)Fix lever A using bolt E. (8)(G) Lock using bolt. (9)Finally, measure the lever angle and set the idle stopper bolt (C) stop position.
----------

----------

Timing setting

Test data 101402-4150
(1)Pump vertical direction (2)Position of gear mark 'CC' at No 1 cylinder's beginning of injection (3)B.T.D.C.: aa (4)-
----------
aa=18deg
----------
a=(90deg)




Have questions with 101402-4150?





Group cross 101402-4150 ZEXEL

Isuzu 

101402-4150  

101402-4151 
F 019 Z10 324 
8970314860 
INJECTION-PUMP ASSEMBLY
4BD1-T
F 019 Z10 325 
8970314861 
INJECTION-PUMP ASSEMBLY
4BD1-T
F 019 Z10 326 
8970314862 
INJECTION-PUMP ASSEMBLY
4BD1-T
F 019 Z10 327 
 
INJECTION-PUMP ASSEMBLY

Isuzu 

9 400 613 895 
8970314863 
INJECTION-PUMP ASSEMBLY
4BD1-T
Back to top