105118-7050 ZEXEL 9 430 612 698 BOSCH NOZZLE AND HOLDER ASSY. 9430612698 1051187050 10015150001


 

Information nozzle and holder assy.

BOSCH 9 430 612 698 9430612698
ZEXEL 105118-7050 1051187050
TOYO-SHA 10015150001 10015150001
105118-7050 NOZZLE AND HOLDER ASSY.
Rating:
42
Buy NOZZLE AND HOLDER ASSY. 105118-7050 zexel genuine, new aftermarket engine parts with delivery

Include in #2:

104298-3020 as NOZZLE AND HOLDER ASSY

Cross reference number

Zexel num
Bosch num
Firm num
Name
105118-7050 
9 430 612 698 
48-2030E 
10015150001  TOYO-SHA
NOZZLE AND HOLDER ASSY.
BD151 K 53KQ NOZZLE & HOLDER ASSY N&NH KBDL2,1-P N&NH




Information:

Start By:a. remove timing gear cover 1. Remove bolt (1) and washer that fastens the weight assembly (2).
Weight assembly must have support during removal to prevent damage to components.
2. Install tooling (A) and remove the weight assembly.Install Automatic Timing Advance Unit
1. Install washer and bolt (1). With the fuel pump housing cover removed, turn the fuel pump camshaft in the direction of engine rotation until tool (A) can be installed in the notch of the camshaft. 2. To time the fuel injection pump to the engine with the front timing cover removed, follow Steps 3 and 4. With the timing cover installed, see Steps 6 and 7. No. 1 piston at top center (TC) on the compression stroke is the starting point for all timing procedures. The engine is seen from the flywheel end when direction of crankshaft rotation is given.3. Turn the crankshaft counterclockwise until the "C" on the crankshaft and camshaft and camshaft gears are in alignment. 4. Remove the plug and install tool (B) in the flywheel housing.5. To find top center compression stroke for No. 1 piston, turn the flywheel clockwise (opposite of engine rotation) approximately 30°. This procedure is to remove all end play from timing gears.6. Turn the flywheel counterclockwise (direction of engine rotation) until tool (B) can be installed in the flywheel. The piston is at top center. If you go past the bolt hole you must start over again. To see if the No. 1 piston is on the compression stroke, remove the breather assembly from the valve cover and look at the valves of the No. 1 cylinder. The valves will be closed if No. 1 cylinder is on the compression stroke. You must be able to move the rocker arms up and down with your hand.7. If NO. 1 piston is not on the compression stroke, remove tooling (B) and turn the flywheel 360° counterclockwise. Install tooling (B). The No. 1 piston is now at top center on the compression stroke.8. With tooling (A) and (B) installed in position, install the timing advance weight assembly on the fuel pump camshaft. 9. Use tool (D) to hold the gear. Install tooling (C) on the weight assembly. While a constant torque on drive gear on 68 N m (50 lb ft) is held, tighten the bolt that fastens the weight assembly to fuel pump camshaft to a torque of 270 25 N m (200 18 lb ft).10. Remove tooling (A), (B) and (C).End By:a. install timing gear coverDisassemble And Assemble Automatic Timing Unit
Start By:a. remove automatic timing advance unit
Keep all parts clean from contaminants. Contaminants put into the system may cause rapid wear and shortened component life.
1. Remove two screws (1) and plate (2).
The weights are held on position with two springs for each weight under compression. Carefully remove weights and springs to prevent possible injury.
2. Remove springs (4) and (5), weight (3) and slide (6) from each side of assembly. 3. If necessary, remove gear (7). Remove

Have questions with 105118-7050?





Group cross 105118-7050 ZEXEL

Isuzu 

 
8944743892 
NOZZLE AND HOLDER ASSY.
4JB1
9 430 610 062 
48-2030C 
8944743893 
NOZZLE AND HOLDER ASSY.
4JB1
9 430 612 696 
48-2031C 
8944743894 
NOZZLE AND HOLDER ASSY.
4JB1

Honda 

9 430 613 141 
 
NOZZLE AND HOLDER ASSY.
ZG3
9 430 610 067 
48-2080G3 
 
NOZZLE AND HOLDER ASSY.

Honda 

9 430 610 072 
48-2081G3 
16410ZG30130 
NOZZLE AND HOLDER ASSY.
ZG4
9 430 612 697 
48-2080G5 
16410ZG50030 
NOZZLE AND HOLDER ASSY.
ZG5

Isuzu 

9 430 613 142 
48-2030A 
8943280901 
NOZZLE AND HOLDER ASSY.
4JB1-TC
9 430 610 069 
48-2090 
8943280902 
NOZZLE AND HOLDER ASSY.
9 430 610 151 
48-2031H 
8943280903 
NOZZLE AND HOLDER ASSY.
4JB1-TC

Toyo-Sha 

105118-7050  
9 430 612 698 
48-2030E 
10015150001 
NOZZLE AND HOLDER ASSY.
BD151
9 430 612 699 
48-2030B 
10115150001 
NOZZLE AND HOLDER ASSY.
BD162
9 430 612 700 
48-2080A 
 
NOZZLE AND HOLDER ASSY.

Honda 

9 430 610 099 
48-2081A 
16410ZG50230 
NOZZLE AND HOLDER ASSY.
ZG5
9 430 610 100 
48-2081E3 
16410ZG38010 
NOZZLE AND HOLDER ASSY.
ZG3
9 430 610 100 
48-2081E3 
16410ZG38012M1 
NOZZLE AND HOLDER ASSY.
ZG3

Fuji-Heavy 

9 430 612 701 
48-2100 
2286320200 
NOZZLE AND HOLDER ASSY.
DY41
Back to top