105011-9360 ZEXEL 9 432 611 910 BOSCH NOZZLE 9432611910 1050119360 8002717016


 

Information nozzle

BOSCH 9 432 611 910 9432611910
ZEXEL 105011-9360 1050119360
KUBOTA 8002717016 8002717016
105011-9360 NOZZLE
Rating:
16
Buy NOZZLE 105011-9360 zexel genuine, new aftermarket engine parts with delivery

Cross reference number

Zexel num
Bosch num
Firm num
Name
105011-9360 
9 432 611 910 
NP-DL135T388NP15 
8002717016  KUBOTA
NOZZLE
C 31BA NOZZLE N(DL-T) N




Information:

3. Remove the connecting rod caps (1) from these pistons, and push the pistons upward until the rings clear the cylinder liner. 4. Remove the two pistons.5. Repeat Step 2 through 4 for the remaining pistons.Install Pistons
1. Thoroughly lubricate the crankshaft bearing journals and cylinder liners with clean SAE 30 engine oil.2. Lubricate the piston rings and connecting rod bearings with clean SAE 30 engine oil. 3. Using compressor (A), install the pistons with "V" mark on piston aligned with "V" mark on cylinder block. Guide the lower end of the rod over the crankshaft journal to prevent damage to the crankshaft.4. Lubricate the threads of cap retaining bolts with clean SAE 30 engine oil.5. Position the caps on the connecting rods, and install retaining nuts. Tighten nuts initially to 30 3 lb. ft. (4,1 0,4 mkg). Mark the nut and end of bolt, and tighten nut an additional 90° from mark.
When installing connecting rod cap, be sure that the number marked on side of cap is adjacent to and corresponds to the number marked on side of connecting rod.
6. Rotate the crankshaft until the next two bearing journals are at bottom dead center.7. Repeat Steps 2 through 5 for the remaining two pistons.concluding steps: a) install oil pumpb) install cylinder head assemblyDisassemble Pistons
preparatory step: a) remove pistons 1. Remove piston pin retaining rings (2).2. Remove piston pin (1) and remove piston from the connecting rod. 3. Remove the piston rings using ring expander (A).Assemble Pistons
1. Using ring expander (A), install the piston rings. The two compression rings are marked "UP - 1" and "UP - 2". The rings must be installed with these marks toward the top of the piston with "UP - 1" being the top ring. After all three rings have been installed on piston, stagger the ring caps 120° apart.2. Lubricate the piston pin with clean SAE 30 engine oil. 3. Position the piston on the connecting rod with the "V" mark (2) on the piston and number (1) on the connecting rod on the same side.4. Install the piston pin retaining rings. Make certain the retaining rings are seated in their grooves.concluding step: a) install pistons

Have questions with 105011-9360?





Group cross 105011-9360 ZEXEL

9 432 610 496 
NP-DL145T428ANP1 
 
HOLE-TYPE NOZZLE
9 432 611 911 
NP-DL140T387NP21 
84032254A 
NOZZLE

Daihatsu 

9 432 610 047 
NP-DL150T308NP22 
E186200110Z 
NOZZLE
9 432 610 301 
NP-DL150T288NP22 
E186200090Z 
NOZZLE
9 432 610 301 
NP-DL150T288NP22 
Y601150288Z 
NOZZLE
9 432 610 032 
NP-DL150T268NP22 
E186210080Z 
NOZZLE
9 432 610 032 
NP-DL150T268NP22 
485311 
NOZZLE
9 432 612 169 
NP-DL150T288NP23 
 
NOZZLE

Kubota 

105011-9360  
9 432 611 910 
NP-DL135T388NP15 
8002717016 
NOZZLE
9 432 610 264 
NP-DL150T308NP15 
 
HOLE-TYPE NOZZLE
9 432 612 170 
NP-DL155T3410NP19 
 
NOZZLE

Mitsubishi 

 
0423403030 
NOZZLE

Mitsubishi-Heav 

 
0423403030 
NOZZLE
Back to top