101607-1600 ZEXEL 9 400 615 627 BOSCH INJECTION-PUMP ASSEMBLY 9400615627 1016071600 me076772


101607-1600 INJECTION-PUMP ASSEMBLY
Rating:
55
Buy INJECTION-PUMP ASSEMBLY 101607-1600 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

BOSCH 9 400 615 627 9400615627
ZEXEL 101607-1600 1016071600
MITSUBISHI ME076772 me076772

Service parts 101607-1600 INJECTION-PUMP ASSEMBLY:

1. _
2. FUEL INJECTION PUMP 101061-9500
3. GOVERNOR 105931-8441
4. SUPPLY PUMP 105210-4641
5. AUTOM. ADVANCE MECHANIS 105643-0750
6. COUPLING PLATE
7. COUPLING PLATE
8. _
9. _
10. NOZZLE AND HOLDER ASSY
11. Nozzle and Holder
12. Open Pre:MPa(Kqf/cm2) 15.7{160}/21.6{220}
13. NOZZLE-HOLDER 105030-4110
14. NOZZLE
15. NOZZLE SET

Include in #1:

101607-1600 as INJECTION-PUMP ASSEMBLY

Cross reference number

BOSCH 9 400 615 627 9400615627
ZEXEL 101607-1600 1016071600
MITSUBISHI ME076772 me076772


Zexel num
Bosch num
Firm num
Name
101607-1600 
9 400 615 627 
ME076772  MITSUBISHI
INJECTION-PUMP ASSEMBLY
6D14 K

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil
  ISO4113 or {SAEJ967d}
Test oil temperature degC   40 40 45
Nozzle and nozzle holder   105780-8140
Bosch type code   EF8511/9A
Nozzle   105780-0000
Bosch type code   DN12SD12T
Nozzle holder   105780-2080
Bosch type code   EF8511/9
Opening pressure MPa   17.2
Opening pressure kgf/cm2   175
Injection pipe
Outer diameter - inner diameter - length (mm)
mm   6-2-600
Overflow valve   131424-5520
Overflow valve opening pressure kPa   255 221 289
Overflow valve opening pressure kgf/cm2   2.6 2.25 2.95
Tester oil delivery pressure kPa   157 157 157
Tester oil delivery pressure kgf/cm2   1.6 1.6 1.6
Direction of rotation (viewed from drive side)
Left
  L
Injection timing adjustment
Direction of rotation (viewed from drive side)
Left
  L
Injection order   1-5-3-6- 2-4
Pre-stroke mm   3.3 3.25 3.35
Beginning of injection position
Governor side
  NO.1
Difference between angles 1
Cal 1-5
deg.   60 59.5 60.5
Difference between angles 2
Cal 1-3
deg.   120 119.5 120.5
Difference between angles 3
Cal 1-6
deg.   180 179.5 180.5
Difference between angles 4
Cyl.1-2
deg.   240 239.5 240.5
Difference between angles 5
Cal 1-4
deg.   300 299.5 300.5
Injection quantity adjustment
Adjusting point   -
Rack position   11.2
Pump speed r/min   850 850 850
Each cylinder's injection qty mm3/st.   57.7 56 59.4
Basic   *
Fixing the rack   *
Standard for adjustment of the maximum variation between cylinders   *
Injection quantity adjustment_02
Adjusting point   H
Rack position   9.5+-0.5
Pump speed r/min   275 275 275
Each cylinder's injection qty mm3/st.   13.7 11.6 15.8
Fixing the rack   *
Standard for adjustment of the maximum variation between cylinders   *
Injection quantity adjustment_03
Adjusting point   A
Rack position   R1(11.2)
Pump speed r/min   850 850 850
Average injection quantity mm3/st.   57.7 56.7 58.7
Basic   *
Fixing the lever   *
Injection quantity adjustment_04
Adjusting point   B
Rack position   R1+0.1
Pump speed r/min   1450 1450 1450
Average injection quantity mm3/st.   72.6 68.6 76.6
Fixing the lever   *
Injection quantity adjustment_05
Adjusting point   C
Rack position   R1+0.8
Pump speed r/min   500 500 500
Average injection quantity mm3/st.   59.7 55.7 63.7
Fixing the lever   *
Injection quantity adjustment_06
Adjusting point   D
Rack position   R1+1.25
Pump speed r/min   300 300 300
Average injection quantity mm3/st.   57.1 53.1 61.1
Fixing the lever   *
Injection quantity adjustment_07
Adjusting point   I
Rack position   -
Pump speed r/min   100 100 100
Average injection quantity mm3/st.   140 130 150
Fixing the lever   *
Rack limit   *
Timer adjustment
Pump speed r/min   1250--
Advance angle deg.   0 0 0
Remarks
Start
 
Timer adjustment_02
Pump speed r/min   1200
Advance angle deg.   0.5
Timer adjustment_03
Pump speed r/min   1400
Advance angle deg.   5 4.5 5.5
Remarks
Finish
 

Test data Ex:

Governor adjustment

Test data 101607-1600
N:Pump speed R:Rack position (mm) (1)Torque cam stamping: T1 (2)RACK LIMIT
----------
T1=F21
----------

Speed control lever angle

Test data 101607-1600
F:Full speed I:Idle (1)Stopper bolt set position 'H'
----------

----------
a=24deg+-5deg b=41deg+-3deg

Stop lever angle

Test data 101607-1600
N:Engine manufacturer's normal use S:Stop the pump. (1)Set the stopper bolt at pump speed = aa and rack position = bb (non-injection rack position). Confirm non-injection. (2)After setting the stopper bolt, confirm non-injection at speed = cc. Rack position = actual (non-injection rack position). (3)Rack position = approximately dd (4)Free (at shipping) (5)Use the hole above R = ee
----------
aa=1550r/min bb=7-0.5mm cc=275r/min dd=15mm ee=40mm
----------
a=36.5deg+-5deg b=(25deg) c=13.5deg+-5deg

0000001501 MICRO SWITCH

Adjustment of the micro-switch Adjust the bolt to obtain the following lever position when the micro-switch is ON. (1)Speed N1 (2)Rack position Ra
----------
N1=400r/min Ra=9.2+-0.1mm
----------

0000001601 LEVER

Test data 101607-1600
(A) Idle (B) Full speed (C) Base lever (D) Accelerator lever (E) Accelerator lever delivery position 1. Measure speed lever angle (1)Measure the angle when the accelerator lever (D) contacted the base lever (C) at a.
----------

----------
b=41deg+-3deg c=24deg+-5deg

Timing setting

Test data 101607-1600
(1)Pump vertical direction (2)Position of timer's tooth at No 1 cylinder's beginning of injection (3)B.T.D.C.: aa (4)-
----------
aa=13deg
----------
a=(0deg)




Have questions with 101607-1600?





Group cross 101607-1600 ZEXEL

Mitsubishi 

101607-1600  
9 400 615 627 
ME076772 
INJECTION-PUMP ASSEMBLY
6D14
9 400 615 628 
ME076769 
INJECTION-PUMP ASSEMBLY
6D16
 
ME306177 
INJECTION-PUMP ASSEMBLY
6D16
9 400 615 629 
ME056900 
INJECTION-PUMP ASSEMBLY
6D22
 
ME056901 
INJECTION-PUMP ASSEMBLY
6D22
9 400 615 630 
ME076785 
INJECTION-PUMP ASSEMBLY
6D16
F 019 Z10 609 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

9 400 615 631 
ME076786 
INJECTION-PUMP ASSEMBLY
6D16T
9 400 615 632 
ME047660 
INJECTION-PUMP ASSEMBLY
6D14T
9 400 615 633 
ME047661 
INJECTION-PUMP ASSEMBLY
6D14T
9 400 615 634 
ME047662 
INJECTION-PUMP ASSEMBLY
6D14T
9 400 615 635 
ME047663 
INJECTION-PUMP ASSEMBLY
6D14T
Back to top