108622-4091 ZEXEL 9 400 619 218 BOSCH INJECTION-PUMP ASSEMBLY 9400619218 1086224091 3310083310

Information Cross number Calibration Data Calibration Data Ex

Price: query
Buy now
Add to cart Go to cart

Rating:

Buy INJECTION-PUMP ASSEMBLY 108622-4091 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

BOSCH 9 400 619 218 9400619218

ZEXEL 108622-4091 1086224091

HYUNDAI 3310083310 3310083310

Service parts 108622-4091 INJECTION-PUMP ASSEMBLY:

1. _

2. FUEL INJECTION PUMP 108062-4001

3. GOVERNOR 105923-5140

4. SUPPLY PUMP 105237-4840

5. AUTOM. ADVANCE MECHANIS

6. COUPLING PLATE 105664-2590

7. COUPLING PLATE

8. _ 159601-7520

9. _ 156640-3720

10. NOZZLE AND HOLDER ASSY 105110-8320

11. Nozzle and Holder

12. Open Pre:MPa(Kqf/cm2) 18.1{185}/24.5{250}

13. NOZZLE-HOLDER 105041-4390

14. NOZZLE

15. NOZZLE SET 105019-2850

Include in #1:

108622-4091 as INJECTION-PUMP ASSEMBLY

Cross reference number

BOSCH 9 400 619 218 9400619218

ZEXEL 108622-4091 1086224091

HYUNDAI 3310083310 3310083310

Zexel num

Bosch num

Firm num

Name

108622-4091

9 400 619 218

3310083310 HYUNDAI

INJECTION-PUMP ASSEMBLY
Q K 14CG INJECTION PUMP ASSY TICS MD-TI6 TICS

Calibration Data:

Adjustment conditions

Test oil
1404 Test oil ISO4113 or {SAEJ967d}

Test oil temperature degC 40 40 45

Nozzle and nozzle holder 105780-8250

Bosch type code 1 688 901 101

Nozzle 105780-0120

Bosch type code 1 688 901 990

Nozzle holder 105780-2190

Opening pressure MPa 20.7

Opening pressure kgf/cm2 211

Injection pipe
Outer diameter - inner diameter - length (mm) mm 8-3-600

Overflow valve 131424-8020

Overflow valve opening pressure kPa 255 221 289

Overflow valve opening pressure kgf/cm2 2.6 2.25 2.95

Tester oil delivery pressure kPa 255 255 255

Tester oil delivery pressure kgf/cm2 2.6 2.6 2.6

PS/ACT control unit part no. 407980-2 24*

Digi switch no. 33

Direction of rotation (viewed from drive side)
Right R

Injection timing adjustment

Direction of rotation (viewed from drive side)
Right R

Injection order 1-5-3-6- 2-4

Pre-stroke mm 6.4 6.37 6.43

Beginning of injection position
Governor side NO.1

Difference between angles 1
Cal 1-5 deg. 60 59.75 60.25

Difference between angles 2
Cal 1-3 deg. 120 119.75 120.25

Difference between angles 3
Cal 1-6 deg. 180 179.75 180.25

Difference between angles 4
Cyl.1-2 deg. 240 239.75 240.25

Difference between angles 5
Cal 1-4 deg. 300 299.75 300.25

Injection quantity adjustment

Adjusting point -

Rack position 14.4

Pump speed r/min 600 600 600

Average injection quantity mm3/st. 155.5 153.5 157.5

Max. variation between cylinders % 0 -2 2

Basic *

Fixing the rack *

PS407980-224* V 2.2+-0.0 1

PS407980-224* mm 4+-0.05

Standard for adjustment of the maximum variation between cylinders *

Injection quantity adjustment_02

Adjusting point H

Rack position 8.5+-0.5

Pump speed r/min 300 300 300

Average injection quantity mm3/st. 22.5 20.5 24.5

Max. variation between cylinders % 0 -15 15

Fixing the rack *

PS407980-224* V V1+0.05+ -0.01

PS407980-224* mm 6.3+-0.0 3

Standard for adjustment of the maximum variation between cylinders *

Remarks
Refer to items regarding the pre-stroke actuator

Injection quantity adjustment_03

Adjusting point A

Rack position R1(14.4)

Pump speed r/min 600 600 600

Average injection quantity mm3/st. 155.5 153.5 157.5

Basic *

Fixing the lever *

Boost pressure kPa 74.6 74.6

Boost pressure mmHg 560 560

PS407980-224* V 2.2+-0.0 1

PS407980-224* mm 4+-0.05

Injection quantity adjustment_04

Adjusting point B

Rack position (R1+1.9) +0.05-0. 1

Pump speed r/min 1000 1000 1000

Average injection quantity mm3/st. 154 148 160

Fixing the lever *

Boost pressure kPa 74.6 74.6

Boost pressure mmHg 560 560

PS407980-224* V 2.2+-0.0 1

PS407980-224* mm 4+-0.05

Boost compensator adjustment

Pump speed r/min 300 300 300

Rack position R1-2.25

Boost pressure kPa 8 6.7 9.3

Boost pressure mmHg 60 50 70

Boost compensator adjustment_02

Pump speed r/min 300 300 300

Rack position R1(14.4)

Boost pressure kPa 61.3 61.3 61.3

Boost pressure mmHg 460 460 460

0000001601

Pre-stroke mm 6.4 6.37 6.43

Remarks
When the timing sleeve is pushed up

_02

Connector angle deg. 11.5 11 12

Remarks
When the eccentric pin is tightened

_03

Supply voltage V 24 23.5 24.5

Ambient temperature degC 23 18 28

Pre-stroke mm 2.4 2.35 2.45

Output voltage V 2.95 2.94 2.96

Adjustment *

_04

Supply voltage V 24 23.5 24.5

Ambient temperature degC 23 18 28

Pre-stroke mm 6.4 6.37 6.43

Output voltage V 1.2 1 1.4

Confirmation *

Remarks
Output voltage V1

_05

Supply voltage V 24 23.5 24.5

Ambient temperature degC 23 18 28

Output voltage V 3.05 3.05

Confirmation of operating range *

Test data Ex:

Governor adjustment

N:Pump speed R:Rack position (mm) (1)Torque cam stamping: T1 (2)Tolerance for racks not indicated: +-0.05mm. (3)Boost compensator stroke: BCL (4)Damper spring setting
----------
T1=AH41 BCL=2.25+-0.1mm
----------

Speed control lever angle

F:Full speed I:Idle (1)Use the hole at R = aa (2)Stopper bolt set position 'H'
----------
aa=37.5mm
----------
a=1deg+-5deg b=(36deg)+-3deg

Stop lever angle

N:Pump normal S:Stop the pump. (1)Pump speed aa, rack position bb (2)Set the stopper screw. (3)Use the hole above R = cc
----------
aa=1200r/min bb=3.5+-0.3mm cc=25mm
----------
a=29.5deg+-5deg b=40deg+-5deg

0000001301

(1)Pump vertical direction (2)Coupling's key groove position at No 1 cylinder's beginning of injection (3)Pre-stroke: aa (4)-
----------
aa=6.4+-0.03mm
----------
a=(0deg)

0000001901

A:Sealing position B:Pre-stroke actuator 1. When installing the pre-stroke actuator on the pump, first tighten the installation bolts loosely, then move the actuator fully counterclockwise (viewed from the drive side). Temporary tightening torque: 1 - 1.5 N.m (0.1 - 0.15 kgf.m) 2. Move the actuator in the clockwise direction when viewed from the drive side, and adjust so that it becomes the adjustment point of the adjustment value. Then tighten it. Tightening torque: 7^9 N.m (0.7^0.9 kgf.m) 3. After prestroke actuator installation adjustment, simultaneously stamp both the actuator side and housing side.
----------

----------

0000002201 MICRO SWITCH

Adjustment of the micro-switch Adjust the bolt to obtain the following lever position when the micro-switch is ON. (1)Speed N1 (2)Rack position Ra
----------
N1=325r/min Ra=9.2+-0.1mm
----------

0000002301 RACK SENSOR

(VR) measurement voltage (I) Part number of the control unit (G) Apply red paint. (H): End surface of the pump 1. Rack sensor adjustment (-0620) (1)Fix the speed control lever at the full position (2)Set the speed to N1 r/min. (If the boost compensator is provided, apply boost pressure.) (3)Adjust the bobbin (A) so that the rack sensor's output voltage is VR+-0.01. (4)At that time, rack position must be Ra. (5)Apply G at two places. Connecting part between the joint (B) and the nut (F) Connecting part between the joint (B) and the end surface of the pump (H)
----------
N1=1000r/min Ra=(R1+1.9)+0.05-0.1mm
----------