108622-3432 ZEXEL F 01G 09U 0FA BOSCH INJECTION-PUMP ASSEMBLY f01g09u0fa 1086223432 220008862a

Information Cross number Calibration Data Calibration Data Ex

Price: query
Buy now
Add to cart Go to cart

Rating:

Buy INJECTION-PUMP ASSEMBLY 108622-3432 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

BOSCH F 01G 09U 0FA f01g09u0fa

ZEXEL 108622-3432 1086223432

HINO 220008862A 220008862a

Service parts 108622-3432 INJECTION-PUMP ASSEMBLY:

1. _

2. FUEL INJECTION PUMP 108062-3251

3. GOVERNOR 105923-1332

4. SUPPLY PUMP 105237-4700

5. AUTOM. ADVANCE MECHANIS

6. COUPLING PLATE 105664-2200

7. COUPLING PLATE 156638-8720

8. _ 159600-2321

9. _

10. NOZZLE AND HOLDER ASSY 105101-7913

11. Nozzle and Holder 23600-2800B

12. Open Pre:MPa(Kqf/cm2) 14.7{150}/21.6{220}

13. NOZZLE-HOLDER 105031-7363

14. NOZZLE

15. NOZZLE SET 105019-0570

Include in #1:

108622-3432 as INJECTION-PUMP ASSEMBLY

Cross reference number

BOSCH F 01G 09U 0FA f01g09u0fa

ZEXEL 108622-3432 1086223432

HINO 220008862A 220008862a

Zexel num

Bosch num

Firm num

Name

108622-3432
108622-3433

F 01G 09U 0FA

220008862A HINO

INJECTION-PUMP ASSEMBLY
K13U-B * K

Calibration Data:

Adjustment conditions

Test oil
1404 Test oil ISO4113 or {SAEJ967d}

Test oil temperature degC 40 40 45

Nozzle and nozzle holder 105780-8250

Bosch type code 1 688 901 101

Nozzle 105780-0120

Bosch type code 1 688 901 990

Nozzle holder 105780-2190

Opening pressure MPa 20.7

Opening pressure kgf/cm2 211

Injection pipe
Outer diameter - inner diameter - length (mm) mm 8-3-600

Overflow valve 134424-4120

Overflow valve opening pressure kPa 255 221 289

Overflow valve opening pressure kgf/cm2 2.6 2.25 2.95

Tester oil delivery pressure kPa 255 255 255

Tester oil delivery pressure kgf/cm2 2.6 2.6 2.6

PS/ACT control unit part no. 407980-2 24*

Digi switch no. 33

Direction of rotation (viewed from drive side)
Left L

Injection timing adjustment

Direction of rotation (viewed from drive side)
Left L

Injection order 1-4-2-6- 3-5

Pre-stroke mm 7.2 7.17 7.23

Beginning of injection position
Drive side NO.1

Difference between angles 1
Cal 1-4 deg. 60 59.75 60.25

Difference between angles 2
Cyl.1-2 deg. 120 119.75 120.25

Difference between angles 3
Cal 1-6 deg. 180 179.75 180.25

Difference between angles 4
Cal 1-3 deg. 240 239.75 240.25

Difference between angles 5
Cal 1-5 deg. 300 299.75 300.25

Injection quantity adjustment

Adjusting point -

Rack position 12.4

Pump speed r/min 700 700 700

Average injection quantity mm3/st. 148 145 151

Max. variation between cylinders % 0 -2 2

Basic *

Fixing the rack *

PS407980-224* V 2.2+-0.0 1

PS407980-224* mm 4.8+-0.0 5

Standard for adjustment of the maximum variation between cylinders *

Injection quantity adjustment_02

Adjusting point Z

Rack position 6.5+-0.5

Pump speed r/min 350 350 350

Average injection quantity mm3/st. 15 12 18

Max. variation between cylinders % 0 -15 15

Fixing the rack *

PS407980-224* V V1+0.05+ -0.01

PS407980-224* mm 7.1+-0.0 3

Standard for adjustment of the maximum variation between cylinders *

Remarks
Refer to items regarding the pre-stroke actuator

Injection quantity adjustment_03

Adjusting point A

Rack position R1(12.4)

Pump speed r/min 700 700 700

Average injection quantity mm3/st. 148 146 150

Basic *

Fixing the lever *

PS407980-224* V 2.2+-0.0 1

PS407980-224* mm 4.8+-0.0 5

Injection quantity adjustment_04

Adjusting point B

Rack position R1+0.8

Pump speed r/min 1075 1075 1075

Average injection quantity mm3/st. 133.5 127.5 139.5

Fixing the lever *

PS407980-224* V 2.2+-0.0 1

PS407980-224* mm 4.8+-0.0 5

0000001601

Pre-stroke mm 7.2 7.17 7.23

Remarks
When the timing sleeve is pushed up

_02

Connector angle deg. 8.5 8 9

Remarks
When the eccentric pin is tightened

_03

Supply voltage V 24 23.5 24.5

Ambient temperature degC 23 18 28

Pre-stroke mm 3.2 3.15 3.25

Output voltage V 2.95 2.94 2.96

Adjustment *

_04

Supply voltage V 24 23.5 24.5

Ambient temperature degC 23 18 28

Pre-stroke mm 7.2 7.17 7.23

Output voltage V 1.2 1 1.4

Confirmation *

Remarks
Output voltage V1

_05

Supply voltage V 24 23.5 24.5

Ambient temperature degC 23 18 28

Output voltage V 3.05 3.05

Confirmation of operating range *

Test data Ex:

Governor adjustment

N:Pump speed R:Rack position (mm) (1)Torque cam stamping: T1 (2)Tolerance for racks not indicated: +-0.05mm. (3)Set stop lever before governor adjustment. [When setting stop lever after governor adjustment, confirm that point B (Ra) can be obtained at full setting.] (4)Stop lever's normal position setting: equivalent to RA (5)Damper spring setting
----------
T1=AD16 Ra=R1+0.8mm RA=16mm
----------

Speed control lever angle

F:Full speed I:Idle (1)Use the hole at R = aa (2)Stopper bolt set position 'H'
----------
aa=36.5mm
----------
a=18deg+-5deg b=(40deg)+-3deg

Stop lever angle

N:Pump normal S:Stop the pump. (1)Set the stopper bolt at rack position = approximately aa. (2)At pump speed bb and rack position cc, set the stopper bolt. (Confirm non-injection at speed = dd.) (3)Use the hole above R = ee
----------
aa=16mm bb=0r/min cc=1.5+-0.3mm dd=1250r/min ee=35mm
----------
a=11deg+-5deg b=31deg+-5deg

0000001301

(1)Pump vertical direction (2)Coupling's key groove position at No 1 cylinder's beginning of injection (3)Pre-stroke: aa (4)-
----------
aa=7.2+-0.03mm
----------
a=(2deg)

0000001901

A:Sealing position B:Pre-stroke actuator 1. When installing the pre-stroke actuator on the pump, first tighten the installation bolts loosely, then move the actuator fully counterclockwise (viewed from the drive side). Temporary tightening torque: 1 - 1.5 N.m (0.1 - 0.15 kgf.m) 2. Move the actuator in the clockwise direction when viewed from the drive side, and adjust so that it becomes the adjustment point of the adjustment value. Then tighten it. Tightening torque: 7^9 N.m (0.7^0.9 kgf.m) 3. After prestroke actuator installation adjustment, simultaneously stamp both the actuator side and housing side.
----------

----------

0000002201 RACK SENSOR

(VR) measurement voltage (I) Part number of the control unit (G) Apply red paint. (H): End surface of the pump 1. Rack sensor adjustment (-0620) (1)Fix the speed control lever at the full position (2)Set the speed to N1 r/min. (If the boost compensator is provided, apply boost pressure.) (3)Adjust the bobbin (A) so that the rack sensor's output voltage is VR+-0.01. (4)At that time, rack position must be Ra. (5)Apply G at two places. Connecting part between the joint (B) and the nut (F) Connecting part between the joint (B) and the end surface of the pump (H)
----------
N1=1075r/min Ra=R1(12.4)+0.8mm
----------

0000002301 AIR CYLINDER

1. Air cylinder adjustment procedure (1)Set the speed lever at idle. (2)Temporarily set the clearance between the speed lever A and the set bolt B at L. (3)Set the speed at N. (4)Apply positive pressure P1 to the air cylinder. (5)Gradually push out the set bolt (B). (6)Tighten the nut (D) at the point where the rack position is Ra at speed N. (7)Apply positive pressure P1 several times. (8)Confirm that the lever returns to the idle position at positive pressure P2.
----------
L=(6)mm N=320r/min P1=392+98kPa(4+1kgf/cm2) P2=0kPa(0kgf/cm2) Ra=6.5+-0.1mm
----------