108622-2210 ZEXEL INJECTION-PUMP ASSEMBLY Calibration Data 1086222210


108622-2210 INJECTION-PUMP ASSEMBLY
Rating:
35
Buy INJECTION-PUMP ASSEMBLY 108622-2210 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

ZEXEL 108622-2210 1086222210

Cross reference number

ZEXEL 108622-2210 1086222210


Zexel num
Bosch num
Firm num
Name
108622-2210 
 
   
INJECTION-PUMP ASSEMBLY

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil
  ISO4113 or {SAEJ967d}
Test oil temperature degC   40 40 45
Nozzle and nozzle holder   105780-8250
Bosch type code   1 688 901 101
Nozzle   105780-0120
Bosch type code   1 688 901 990
Nozzle holder   105780-2190
Opening pressure MPa   20.7
Opening pressure kgf/cm2   211
Injection pipe
Outer diameter - inner diameter - length (mm)
mm   8-3-600
Overflow valve   131425-0220
Overflow valve opening pressure kPa   157 123 191
Overflow valve opening pressure kgf/cm2   1.6 1.25 1.95
Tester oil delivery pressure kPa   255 255 255
Tester oil delivery pressure kgf/cm2   2.6 2.6 2.6
PS/ACT control unit part no.   407980-2 24*
Digi switch no.   31
Direction of rotation (viewed from drive side)
Right
  R
Injection timing adjustment
Direction of rotation (viewed from drive side)
Right
  R
Injection order   1-5-3-6- 2-4
Pre-stroke mm   8.5 8.47 8.53
Beginning of injection position
Governor side
  NO.1
Difference between angles 1
Cal 1-5
deg.   60 59.75 60.25
Difference between angles 2
Cal 1-3
deg.   120 119.75 120.25
Difference between angles 3
Cal 1-6
deg.   180 179.75 180.25
Difference between angles 4
Cyl.1-2
deg.   240 239.75 240.25
Difference between angles 5
Cal 1-4
deg.   300 299.75 300.25
Injection quantity adjustment
Adjusting point   -
Rack position   14.7
Pump speed r/min   700 700 700
Average injection quantity mm3/st.   166 163 169
Max. variation between cylinders %   0 -2 2
Basic   *
Fixing the rack   *
PS407980-224* V   2.45+-0. 01
PS407980-224* mm   6.1+-0.0 5
Standard for adjustment of the maximum variation between cylinders   *
Injection quantity adjustment_02
Adjusting point   Z
Rack position   8.4+-0.5
Pump speed r/min   410 410 410
Average injection quantity mm3/st.   14 12 16
Max. variation between cylinders %   0 -15 15
Fixing the rack   *
PS407980-224* V   V1+0.05+ -0.01
PS407980-224* mm   8.4+-0.0 3
Standard for adjustment of the maximum variation between cylinders   *
Remarks
Refer to items regarding the pre-stroke actuator
 
Injection quantity adjustment_03
Adjusting point   A
Rack position   R1(14.7)
Pump speed r/min   700 700 700
Average injection quantity mm3/st.   166 164 168
Basic   *
Fixing the lever   *
Boost pressure kPa   29.3 29.3
Boost pressure mmHg   220 220
PS407980-224* V   2.45+-0. 01
PS407980-224* mm   6.1+-0.0 5
Injection quantity adjustment_04
Adjusting point   B
Rack position   R1+1
Pump speed r/min   1100 1100 1100
Average injection quantity mm3/st.   155 151 159
Fixing the lever   *
Boost pressure kPa   29.3 29.3
Boost pressure mmHg   220 220
PS407980-224* V   2.45+-0. 01
PS407980-224* mm   6.1+-0.0 5
Boost compensator adjustment
Pump speed r/min   250 250 250
Rack position   R2-2
Boost pressure kPa   6.7 5.4 8
Boost pressure mmHg   50 40 60
Boost compensator adjustment_02
Pump speed r/min   250 250 250
Rack position   R2(R1-1. 8)
Boost pressure kPa   16 16 16
Boost pressure mmHg   120 120 120
0000001601
Pre-stroke mm   8.5 8.47 8.53
Remarks
When the timing sleeve is pushed up
 
_02
Connector angle deg.   8.5 8 9
Remarks
When the eccentric pin is tightened
 
_03
Supply voltage V   24 23.5 24.5
Ambient temperature degC   23 18 28
Pre-stroke mm   6.1 6.05 6.15
Output voltage V   2.45 2.44 2.46
Adjustment   *
_04
Supply voltage V   24 23.5 24.5
Ambient temperature degC   23 18 28
Pre-stroke mm   8.5 8.47 8.53
Output voltage V   1.2 1 1.4
Confirmation   *
Remarks
Output voltage V1
 
_05
Supply voltage V   24 23.5 24.5
Ambient temperature degC   23 18 28
Pre-stroke mm   5.5
Output voltage V   3 2.98 3
Confirmation   *
_06
Supply voltage V   24 23.5 24.5
Ambient temperature degC   23 18 28
Output voltage V   3.05 3.05
Confirmation of operating range   *

Test data Ex:

Governor adjustment

Test data 108622-2210
N:Pump speed R:Rack position (mm) (1)Torque cam stamping: T1 (2)Tolerance for racks not indicated: +-0.05mm. (3)Boost compensator stroke: BCL (4)Damper spring setting
----------
T1=AE37 BCL=2+-0.1mm
----------

Speed control lever angle

Test data 108622-2210
F:Full speed I:Idle (1)Use the hole at R = aa (2)Stopper bolt set position 'H' (3)Viewed from feed pump side.
----------
aa=37.5mm
----------
a=17.5deg+-5deg b=33.5deg+-3deg

Stop lever angle

Test data 108622-2210
N:Pump normal S:Stop the pump. (1)Use the hole at R = aa (2)Normal engine position (Rack position corresponding to bb) (3)Set the stopper bolt so that speed = cc and rack position = dd (and confirm non-injection).
----------
aa=54mm bb=18mm cc=1100r/min dd=4+-0.3mm
----------
a=40deg+-5deg b=29.5deg+-5deg c=(30deg)

0000001301

Test data 108622-2210
(1)Pump vertical direction (2)Coupling's key groove position at No 1 cylinder's beginning of injection (3)At the No 1 cylinder's beginning of injection position, stamp an aligning mark on the damper to align with the pointer's groove. (4)Damper (5)Pointer (6)B.T.D.C.: aa (7)Pre-stroke: bb
----------
aa=5deg bb=8.5+-0.03mm
----------
a=(0deg) b=(44deg)

0000001901

Test data 108622-2210
A:Sealing position B:Pre-stroke actuator 1. When installing the pre-stroke actuator on the pump, first tighten the installation bolts loosely, then move the actuator fully counterclockwise (viewed from the drive side). Temporary tightening torque: 1 - 1.5 N.m (0.1 - 0.15 kgf.m) 2. Move the actuator in the clockwise direction when viewed from the drive side, and adjust so that it becomes the adjustment point of the adjustment value. Then tighten it. Tightening torque: 7^9 N.m (0.7^0.9 kgf.m) 3. After prestroke actuator installation adjustment, simultaneously stamp both the actuator side and housing side.
----------

----------

0000002201 RACK SENSOR

Test data 108622-2210
(VR) measurement voltage (I) Part number of the control unit (G) Apply red paint. (H): End surface of the pump 1. Rack sensor adjustment (-0620) (1)Fix the speed control lever at the full position (2)Set the speed to N1 r/min. (If the boost compensator is provided, apply boost pressure.) (3)Adjust the bobbin (A) so that the rack sensor's output voltage is VR+-0.01. (4)At that time, rack position must be Ra. (5)Apply G at two places. Connecting part between the joint (B) and the nut (F) Connecting part between the joint (B) and the end surface of the pump (H)
----------
N1=1100r/min Ra=R1(14.7)+1mm
----------

0000002301 MICRO SWITCH

Adjustment of the micro-switch Adjust the bolt to obtain the following lever position when the micro-switch is ON. (1)Speed N1 (2)Rack position Ra
----------
N1=325r/min Ra=8+-0.1mm
----------




Have questions with 108622-2210?





Group cross 108622-2210 ZEXEL

9 400 612 876 
 
INJECTION-PUMP ASSEMBLY
 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

9 400 619 145 
ME152177 
INJECTION-PUMP ASSEMBLY
6D24
108622-2210  
 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

9 400 619 146 
ME152322 
INJECTION-PUMP ASSEMBLY
6D24T2
9 400 612 877 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

9 400 612 878 
ME152265 
INJECTION-PUMP ASSEMBLY
6D24
9 400 612 879 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

9 400 612 880 
ME152266 
INJECTION-PUMP ASSEMBLY
6D24
9 400 612 881 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

9 400 619 147 
ME152523 
INJECTION-PUMP ASSEMBLY
6D24
 
 
INJECTION-PUMP ASSEMBLY
9 400 619 702 
 
INJECTION-PUMP ASSEMBLY
 
 
INJECTION-PUMP ASSEMBLY
6D24T2

Mitsubishi 

9 400 619 148 
ME152420 
INJECTION-PUMP ASSEMBLY
6D24T2
 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

9 400 619 149 
ME152560 
INJECTION-PUMP ASSEMBLY
6D24
9 400 612 882 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

9 400 619 150 
ME121680 
INJECTION-PUMP ASSEMBLY
6D40T1
 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

9 400 612 089 
ME121681 
INJECTION-PUMP ASSEMBLY
6D40T1
9 400 611 169 
 
INJECTION-PUMP ASSEMBLY
9 400 611 199 
 
INJECTION-PUMP ASSEMBLY
6D24T2

Mitsubishi 

9 400 619 151 
ME153012 
INJECTION-PUMP ASSEMBLY
6D24T2
Back to top