108622-2102 ZEXEL 9 400 619 137 BOSCH INJECTION-PUMP ASSEMBLY 9400619137 1086222102 me151724

Information Cross number Calibration Data Calibration Data Ex

Price: query
Buy now
Add to cart Go to cart

Rating:

Buy INJECTION-PUMP ASSEMBLY 108622-2102 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

BOSCH 9 400 619 137 9400619137

ZEXEL 108622-2102 1086222102

MITSUBISHI ME151724 me151724

Service parts 108622-2102 INJECTION-PUMP ASSEMBLY:

1. _

2. FUEL INJECTION PUMP 108062-3450

3. GOVERNOR 105952-1530

4. SUPPLY PUMP 105237-4840

5. AUTOM. ADVANCE MECHANIS

6. COUPLING PLATE 105664-0990

7. COUPLING PLATE

8. _ 159600-4021

9. _ 156641-0920

10. NOZZLE AND HOLDER ASSY 105110-7411

11. Nozzle and Holder ME151252

12. Open Pre:MPa(Kqf/cm2) 17.7{180}/24.5{250}

13. NOZZLE-HOLDER 105041-4111

14. NOZZLE

15. NOZZLE SET 105019-0430

Include in #1:

108622-2102 as INJECTION-PUMP ASSEMBLY

Cross reference number

BOSCH 9 400 619 137 9400619137

ZEXEL 108622-2102 1086222102

MITSUBISHI ME151724 me151724

Zexel num

Bosch num

Firm num

Name

108622-2102

9 400 619 137

ME151724 MITSUBISHI

INJECTION-PUMP ASSEMBLY
6D24 K

Calibration Data:

Adjustment conditions

Test oil
1404 Test oil ISO4113 or {SAEJ967d}

Test oil temperature degC 40 40 45

Nozzle and nozzle holder 105780-8250

Bosch type code 1 688 901 101

Nozzle 105780-0120

Bosch type code 1 688 901 990

Nozzle holder 105780-2190

Opening pressure MPa 20.7

Opening pressure kgf/cm2 211

Injection pipe
Outer diameter - inner diameter - length (mm) mm 8-3-600

Overflow valve 131425-0220

Overflow valve opening pressure kPa 157 123 191

Overflow valve opening pressure kgf/cm2 1.6 1.25 1.95

Tester oil delivery pressure kPa 255 255 255

Tester oil delivery pressure kgf/cm2 2.6 2.6 2.6

RED3 control unit part number 407910-2 470

RED3 rack sensor specifications mm 15

PS/ACT control unit part no. 407980-2 24*

Digi switch no. 31

Direction of rotation (viewed from drive side)
Right R

Injection timing adjustment

Direction of rotation (viewed from drive side)
Right R

Injection order 1-5-3-6- 2-4

Pre-stroke mm 8.5 8.47 8.53

Beginning of injection position
Governor side NO.1

Difference between angles 1
Cal 1-5 deg. 60 59.75 60.25

Difference between angles 2
Cal 1-3 deg. 120 119.75 120.25

Difference between angles 3
Cal 1-6 deg. 180 179.75 180.25

Difference between angles 4
Cyl.1-2 deg. 240 239.75 240.25

Difference between angles 5
Cal 1-4 deg. 300 299.75 300.25

Injection quantity adjustment

Rack position (11.2)

Vist V 1.76 1.76 1.76

Pump speed r/min 700 700 700

Average injection quantity mm3/st. 127.5 126.5 128.5

Max. variation between cylinders % 0 -2 2

Basic *

PS407980-224* V 2.45+-0. 01

PS407980-224* mm 6.1+-0.0 5

Injection quantity adjustment_02

Rack position (7)

Vist V 2.6 2.5 2.7

Pump speed r/min 325 325 325

Average injection quantity mm3/st. 20 18 22

Max. variation between cylinders % 0 -15 15

PS407980-224* V V1+0.05+ -0.01

PS407980-224* mm 8.4+-0.0 3

Remarks
Refer to items regarding the pre-stroke actuator

0000001201

Pre-stroke mm 8.5 8.47 8.53

Remarks
When the timing sleeve is pushed up

_02

Connector angle deg. 8.5 8 9

Remarks
When the eccentric pin is tightened

_03

Supply voltage V 24 23.5 24.5

Ambient temperature degC 23 18 28

Pre-stroke mm 6.1 6.05 6.15

Output voltage V 2.45 2.44 2.46

Adjustment *

_04

Supply voltage V 24 23.5 24.5

Ambient temperature degC 23 18 28

Pre-stroke mm 8.5 8.47 8.53

Output voltage V 1.2 1 1.4

Confirmation *

Remarks
Output voltage V1

_05

Supply voltage V 24 23.5 24.5

Ambient temperature degC 23 18 28

Pre-stroke mm 5.5

Output voltage V 3 2.98 3

Confirmation *

_06

Supply voltage V 24 23.5 24.5

Ambient temperature degC 23 18 28

Output voltage V 3.05 3.05

Confirmation of operating range *

Test data Ex:

Speed control lever angle

N:Pump normal S:Stop the pump. (1)Rack position = aa (2)Rack position bb
----------
aa=1mm bb=16mm
----------
a=19deg+-5deg b=29deg+-5deg

0000000901

(1)Pump vertical direction (2)Coupling's key groove position at No 1 cylinder's beginning of injection (3)At the No 1 cylinder's beginning of injection position, stamp an aligning mark on the damper to align with the pointer's groove. (4)Damper (5)Pointer (6)B.T.D.C.: aa (7)Pre-stroke: bb
----------
aa=4deg bb=8.5+-0.03mm
----------
a=(0deg) b=(44deg)

0000001501

A:Sealing position B:Pre-stroke actuator 1. When installing the pre-stroke actuator on the pump, first tighten the installation bolts loosely, then move the actuator fully counterclockwise (viewed from the drive side). Temporary tightening torque: 1 - 1.5 N.m (0.1 - 0.15 kgf.m) 2. Move the actuator in the clockwise direction when viewed from the drive side, and adjust so that it becomes the adjustment point of the adjustment value. Then tighten it. Tightening torque: 7^9 N.m (0.7^0.9 kgf.m) 3. After prestroke actuator installation adjustment, simultaneously stamp both the actuator side and housing side.
----------

----------

0000001701

(Rs) rack sensor specifications (C/U) control unit part number (V) Rack sensor output voltage (R) Rack position (mm) 1. Confirming governor output characteristics (rack 15 mm, span 6 mm) (1)When the output voltages of the rack sensor are V1 and V2, check that the rack positions R1 and R2 in the table above are satisfied.
----------

----------

0000001901 RACK SENSOR

(VR) measurement voltage (I) Part number of the control unit (G) Apply red paint. (H): End surface of the pump 1. Rack sensor adjustment (154610-0620) (1)At governor side rack sensor output voltage V1, adjust the bobbin (A) so that the drive side rack sensor output voltage is VR+-0.01. (2)Apply G at two places. Connecting part between the joint (B) and the nut (F) Connecting part between the joint (B) and the end surface of the pump (H)
----------
V1=1V
----------