108622-0000 ZEXEL 9 400 612 831 BOSCH INJECTION-PUMP ASSEMBLY 9400612831 1086220000


108622-0000 INJECTION-PUMP ASSEMBLY
Rating:
84
Buy INJECTION-PUMP ASSEMBLY 108622-0000 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

BOSCH 9 400 612 831 9400612831
ZEXEL 108622-0000 1086220000

Service parts 108622-0000 INJECTION-PUMP ASSEMBLY:

1. _
2. FUEL INJECTION PUMP 108062-0000
3. GOVERNOR 105952-0640
4. SUPPLY PUMP 105237-1880
5. AUTOM. ADVANCE MECHANIS
6. COUPLING PLATE 105664-0750
7. COUPLING PLATE 156638-0920
9. _
10. NOZZLE AND HOLDER ASSY 105101-6160
11. Nozzle and Holder 16600-96570
12. Open Pre:MPa(Kqf/cm2) 19.6{200}
13. NOZZLE-HOLDER 105031-4370
14. NOZZLE 105015-8430
15. NOZZLE SET

Include in #1:

108622-0000 as INJECTION-PUMP ASSEMBLY

Cross reference number

BOSCH 9 400 612 831 9400612831
ZEXEL 108622-0000 1086220000


Zexel num
Bosch num
Firm num
Name
108622-0000 
108622-0001 
9 400 612 831 
  NISSAN-DIESEL
INJECTION-PUMP ASSEMBLY
PF6TA K 14CP INJECTION PUMP ASSY TICS HD-TI6F TICS

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil
  ISO4113 or {SAEJ967d}
Test oil temperature degC   40 40 45
Nozzle and nozzle holder   105780-8140
Bosch type code   EF8511/9A
Nozzle   105780-0000
Bosch type code   DN12SD12T
Nozzle holder   105780-2080
Bosch type code   EF8511/9
Opening pressure MPa   17.2
Opening pressure kgf/cm2   175
Injection pipe
Outer diameter - inner diameter - length (mm)
mm   8-3-600
Overflow valve   134424-4120
Overflow valve opening pressure kPa   255 221 289
Overflow valve opening pressure kgf/cm2   2.6 2.25 2.95
Tester oil delivery pressure kPa   157 157 157
Tester oil delivery pressure kgf/cm2   1.6 1.6 1.6
RED3 control unit part number   407910-2 470
RED3 rack sensor specifications mm   15
PS/ACT control unit part no.   407980-2 24*
Digi switch no.   32
Direction of rotation (viewed from drive side)
Right
  R
Injection timing adjustment
Direction of rotation (viewed from drive side)
Right
  R
Injection order   1-4-2-6- 3-5
Pre-stroke mm   5.6 5.57 5.63
Beginning of injection position
Drive side
  NO.1
Difference between angles 1
Cal 1-4
deg.   60 59.75 60.25
Difference between angles 2
Cyl.1-2
deg.   120 119.75 120.25
Difference between angles 3
Cal 1-6
deg.   180 179.75 180.25
Difference between angles 4
Cal 1-3
deg.   240 239.75 240.25
Difference between angles 5
Cal 1-5
deg.   300 299.75 300.25
Injection quantity adjustment
Rack position   (12.7)
Vist V   1.45 1.45 1.45
Pump speed r/min   600 600 600
Average injection quantity mm3/st.   168.1 166.1 170.1
Max. variation between cylinders %   0 -4 4
Basic   *
PS407980-224* V   V1+0.1
PS407980-224* mm   5.4+-0.0 3
Remarks
Refer to items regarding the pre-stroke actuator
 
Injection quantity adjustment_02
Rack position   (7.3)
Vist V   2.5 2.4 2.6
Pump speed r/min   225 225 225
Average injection quantity mm3/st.   8 7 9
Max. variation between cylinders %   0 -10 10
PS407980-224* V   V1+0.1
PS407980-224* mm   5.4+-0.0 3
0000001201
Pre-stroke mm   5.6 5.57 5.63
Remarks
When the timing sleeve is pushed up
 
_02
Connector angle deg.   5 4.5 5.5
Remarks
When the eccentric pin is tightened
 
_03
Supply voltage V   24 23.5 24.5
Ambient temperature degC   23 18 28
Pre-stroke mm   5.6 5.57 5.63
Output voltage V   1.2 1.05 1.35
Adjustment   *
Remarks
Output voltage V1
 
_04
Supply voltage V   24 23.5 24.5
Ambient temperature degC   23 18 28
Pre-stroke mm   2.6 2.32 2.88
Output voltage V   2.7 2.53 2.87
Confirmation   *
_05
Supply voltage V   24 23.5 24.5
Ambient temperature degC   23 18 28
Output voltage V   2.85 2.85
Confirmation of operating range   *

Test data Ex:

Speed control lever angle

Test data 108622-0000
N:Pump normal S:Stop the pump. (1)Rack position = aa (2)Rack position bb
----------
aa=16mm bb=1mm
----------
a=12deg+-5deg b=29deg+-5deg

0000000901

Test data 108622-0000
(1)Pump vertical direction (2)Coupling's key groove position at No 1 cylinder's beginning of injection (3)Pre-stroke: aa (4)-
----------
aa=5.6+-0.03mm
----------
a=(30deg)

0000001701

Test data 108622-0000
(Rs) rack sensor specifications (C/U) control unit part number (V) Rack sensor output voltage (R) Rack position (mm) 1. Confirming governor output characteristics (rack 15 mm, span 6 mm) (1)When the output voltages of the rack sensor are V1 and V2, check that the rack positions R1 and R2 in the table above are satisfied.
----------

----------




Have questions with 108622-0000?





Group cross 108622-0000 ZEXEL

Nissan-Diesel 

108622-0000  

108622-0001 
9 400 612 831 
 
INJECTION-PUMP ASSEMBLY
PF6TA
9 400 612 832 
 
INJECTION-PUMP ASSEMBLY

Nissan-Diesel 

9 400 612 979 
1680196611 
INJECTION-PUMP ASSEMBLY
PF6TA
 
 
INJECTION-PUMP ASSEMBLY
9 400 612 833 
 
INJECTION-PUMP ASSEMBLY

Nissan-Diesel 

9 400 612 834 
1680196612 
INJECTION-PUMP ASSEMBLY
PF6TA
 
 
INJECTION-PUMP ASSEMBLY
9 400 612 835 
 
INJECTION-PUMP ASSEMBLY
9 400 612 836 
 
INJECTION-PUMP ASSEMBLY

Nissan-Diesel 

9 400 612 837 
1680195505 
INJECTION-PUMP ASSEMBLY
NF6TA
 
 
INJECTION-PUMP ASSEMBLY
 
 
INJECTION-PUMP ASSEMBLY
9 400 612 838 
 
INJECTION-PUMP ASSEMBLY

Nissan-Diesel 

9 400 612 839 
1680195506 
INJECTION-PUMP ASSEMBLY
NF6TA
 
 
INJECTION-PUMP ASSEMBLY
9 400 612 840 
 
INJECTION-PUMP ASSEMBLY
9 400 612 841 
 
INJECTION-PUMP ASSEMBLY

Nissan-Diesel 

9 400 612 842 
1680196613 
INJECTION-PUMP ASSEMBLY
PF6TA
9 400 612 843 
1671396915 
INJECTION-PUMP ASSEMBLY
D0XB
9 400 612 844 
1671396916 
INJECTION-PUMP ASSEMBLY
D0XC
9 400 612 845 
1671396919 
INJECTION-PUMP ASSEMBLY
D0XB
9 400 612 846 
1671396960 
INJECTION-PUMP ASSEMBLY
D0XC
9 400 612 847 
 
INJECTION-PUMP ASSEMBLY
9 400 612 848 
 
INJECTION-PUMP ASSEMBLY
9 400 612 849 
 
INJECTION-PUMP ASSEMBLY
 
 
INJECTION-PUMP ASSEMBLY
9 400 619 890 
 
INJECTION-PUMP ASSEMBLY
 
 
INJECTION-PUMP ASSEMBLY

Nissan-Diesel 

9 400 612 980 
1680196617 
INJECTION-PUMP ASSEMBLY
PF6TB
Back to top