108621-2010 ZEXEL INJECTION-PUMP ASSEMBLY Calibration Data 1086212010


108621-2010 INJECTION-PUMP ASSEMBLY
Rating:
60
Buy INJECTION-PUMP ASSEMBLY 108621-2010 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

ZEXEL 108621-2010 1086212010

Cross reference number

ZEXEL 108621-2010 1086212010


Zexel num
Bosch num
Firm num
Name
108621-2010 
 
   
INJECTION-PUMP ASSEMBLY

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil
  ISO4113 or {SAEJ967d}
Test oil temperature degC   40 40 45
Nozzle and nozzle holder   105780-8250
Bosch type code   1 688 901 101
Nozzle   105780-0120
Bosch type code   1 688 901 990
Nozzle holder   105780-2190
Opening pressure MPa   20.7
Opening pressure kgf/cm2   211
Injection pipe
Outer diameter - inner diameter - length (mm)
mm   8-3-600
Overflow valve   131424-7220
Overflow valve opening pressure kPa   255 221 289
Overflow valve opening pressure kgf/cm2   2.6 2.25 2.95
Tester oil delivery pressure kPa   255 255 255
Tester oil delivery pressure kgf/cm2   2.6 2.6 2.6
RED3 control unit part number   407910-2 470
RED3 rack sensor specifications mm   15
PS/ACT control unit part no.   407980-2 24*
Digi switch no.   21
Direction of rotation (viewed from drive side)
Left
  L
Injection timing adjustment
Direction of rotation (viewed from drive side)
Left
  L
Injection order   1-5-3-6- 2-4
Pre-stroke mm   5.6 5.57 5.63
Beginning of injection position
Governor side
  NO.1
Difference between angles 1
Cal 1-5
deg.   60 59.75 60.25
Difference between angles 2
Cal 1-3
deg.   120 119.75 120.25
Difference between angles 3
Cal 1-6
deg.   180 179.75 180.25
Difference between angles 4
Cyl.1-2
deg.   240 239.75 240.25
Difference between angles 5
Cal 1-4
deg.   300 299.75 300.25
Injection quantity adjustment
Rack position   (12.9)
Vist V   1.42 1.42 1.42
Pump speed r/min   650 650 650
Average injection quantity mm3/st.   148.5 147.5 149.5
Max. variation between cylinders %   0 -2 2
Basic   *
PS407980-224* V   V1+1.44+ -0.01
PS407980-224* mm   3.2+-0.0 5
Remarks
Refer to items regarding the pre-stroke actuator
 
Injection quantity adjustment_02
Rack position   (6.5)
Vist V   2.7 2.6 2.8
Pump speed r/min   250 250 250
Average injection quantity mm3/st.   10.5 8.5 12.5
Max. variation between cylinders %   0 -15 15
PS407980-224* V   V1+0.13+ -0.01
PS407980-224* mm   5.4+-0.0 3
Governor adjustment
Pump speed r/min   700--
Remarks
Start
 
Governor adjustment_02
Pump speed r/min   650
Advance angle deg.   0.5
Governor adjustment_03
Pump speed r/min   850
Advance angle deg.   2 1.5 2.5
Remarks
Finish
 
0000001201
Pre-stroke mm   5.6 5.57 5.63
Remarks
When the timing sleeve is pushed up
 
_02
Connector angle deg.   5 4.5 5.5
Remarks
When the eccentric pin is tightened
 
_03
Supply voltage V   24 23.5 24.5
Ambient temperature degC   23 18 28
Pre-stroke mm   5.6 5.57 5.63
Output voltage V   1 1 1.05
Adjustment   *
Remarks
Output voltage V1
 
_04
Supply voltage V   24 23.5 24.5
Ambient temperature degC   23 18 28
Pre-stroke mm   2.6 2.32 2.88
Output voltage V   2.8 2.78 2.87
Confirmation   *
_05
Supply voltage V   24 23.5 24.5
Ambient temperature degC   23 18 28
Output voltage V   3.05 3.05
Confirmation of operating range   *

Test data Ex:

Speed control lever angle

Test data 108621-2010
N:Pump normal S:Stop the pump. (1)Rack position = aa (2)Rack position bb
----------
aa=16mm bb=1mm
----------
a=19deg+-5deg b=29deg+-5deg

0000000901

Test data 108621-2010
(1)Pump vertical direction (2)Coupling's key groove position at No 1 cylinder's beginning of injection (3)Pre-stroke: aa (4)-
----------
aa=5.6+-0.03mm
----------
a=(2deg)

0000001701

Test data 108621-2010
(Rs) rack sensor specifications (C/U) control unit part number (V) Rack sensor output voltage (R) Rack position (mm) 1. Confirming governor output characteristics (rack 15 mm, span 6 mm) (1)When the output voltages of the rack sensor are V1 and V2, check that the rack positions R1 and R2 in the table above are satisfied.
----------

----------




Have questions with 108621-2010?





Group cross 108621-2010 ZEXEL

108621-2010  
 
 
INJECTION-PUMP ASSEMBLY
 
 
INJECTION-PUMP ASSEMBLY
 
 
INJECTION-PUMP ASSEMBLY
 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

9 400 619 094 
ME120867 
INJECTION-PUMP ASSEMBLY
6D40T1
Back to top