108621-0040 ZEXEL INJECTION-PUMP ASSEMBLY Calibration Data 1086210040


108621-0040 INJECTION-PUMP ASSEMBLY
Rating:
22
Buy INJECTION-PUMP ASSEMBLY 108621-0040 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

ZEXEL 108621-0040 1086210040

Cross reference number

ZEXEL 108621-0040 1086210040


Zexel num
Bosch num
Firm num
Name
108621-0040 
 
   
INJECTION-PUMP ASSEMBLY

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil
  ISO4113 or {SAEJ967d}
Test oil temperature degC   40 40 45
Nozzle and nozzle holder   105780-8250
Bosch type code   1 688 901 101
Nozzle   105780-0120
Bosch type code   1 688 901 990
Nozzle holder   105780-2190
Opening pressure MPa   20.7
Opening pressure kgf/cm2   211
Injection pipe
Outer diameter - inner diameter - length (mm)
mm   8-3-600
Overflow valve   134424-4120
Overflow valve opening pressure kPa   255 221 289
Overflow valve opening pressure kgf/cm2   2.6 2.25 2.95
Tester oil delivery pressure kPa   255 255 255
Tester oil delivery pressure kgf/cm2   2.6 2.6 2.6
RED4 control unit part number   407915-0 590
RED4 rack sensor specifications mm   19
PS/ACT control unit part no.   407980-2 24*
Digi switch no.   33
Direction of rotation (viewed from drive side)
Right
  R
Injection timing adjustment
Direction of rotation (viewed from drive side)
Right
  R
Injection order   1-4-2-6- 3-5
Pre-stroke mm   6.4 6.37 6.43
Beginning of injection position
Drive side
  NO.1
Difference between angles 1
Cal 1-4
deg.   60 59.75 60.25
Difference between angles 2
Cyl.1-2
deg.   120 119.75 120.25
Difference between angles 3
Cal 1-6
deg.   180 179.75 180.25
Difference between angles 4
Cal 1-3
deg.   240 239.75 240.25
Difference between angles 5
Cal 1-5
deg.   300 299.75 300.25
Injection quantity adjustment
Rack position   (15.2)
PWM %   73.6
Pump speed r/min   650 650 650
Average injection quantity mm3/st.   170 168 172
Max. variation between cylinders %   0 -4 4
Basic   *
PS407980-224* V   2.2+-0.0 1
PS407980-224* mm   4+-0.05
Injection quantity adjustment_02
Rack position   (7.4)
PWM %   29.9+-2. 8
Pump speed r/min   295 295 295
Average injection quantity mm3/st.   16.6 15.6 17.6
Max. variation between cylinders %   0 -10 10
PS407980-224* V   V1+0.05+ -0.01
PS407980-224* mm   6.3+-0.0 3
Remarks
Refer to items regarding the pre-stroke actuator
 
Governor adjustment
Pump speed r/min   950--
Advance angle deg.   0 0 0
Remarks
Start
 
Governor adjustment_02
Pump speed r/min   900
Advance angle deg.   0.5
Governor adjustment_03
Pump speed r/min   1000
Advance angle deg.   1.5 1 2
Remarks
Finish
 
0000001201
Pre-stroke mm   6.4 6.37 6.43
Remarks
When the timing sleeve is pushed up
 
_02
Connector angle deg.   11.5 11 12
Remarks
When the eccentric pin is tightened
 
_03
Supply voltage V   24 23.5 24.5
Ambient temperature degC   23 18 28
Pre-stroke mm   2.4 2.35 2.45
Output voltage V   2.95 2.94 2.96
Adjustment   *
_04
Supply voltage V   24 23.5 24.5
Ambient temperature degC   23 18 28
Pre-stroke mm   6.4 6.37 6.43
Output voltage V   1.2 1 1.4
Confirmation   *
Remarks
Output voltage V1
 
_05
Supply voltage V   24 23.5 24.5
Ambient temperature degC   23 18 28
Output voltage V   3.05 3.05
Confirmation of operating range   *

Test data Ex:

Speed control lever angle

Test data 108621-0040
N:Pump normal S:Stop the pump. (1)Rack position = aa (2)Rack position bb
----------
aa=20mm bb=1mm
----------
a=20deg+-5deg b=37deg+-5deg

0000000901

Test data 108621-0040
(1)Pump vertical direction (2)Coupling's key groove position at No 1 cylinder's beginning of injection (3)Pre-stroke: aa (4)-
----------
aa=6.4+-0.03mm
----------
a=(20deg)

0000001501

Test data 108621-0040
A:Sealing position B:Pre-stroke actuator 1. When installing the pre-stroke actuator on the pump, first tighten the installation bolts loosely, then move the actuator fully counterclockwise (viewed from the drive side). Temporary tightening torque: 1 - 1.5 N.m (0.1 - 0.15 kgf.m) 2. Move the actuator in the clockwise direction when viewed from the drive side, and adjust so that it becomes the adjustment point of the adjustment value. Then tighten it. Tightening torque: 7^9 N.m (0.7^0.9 kgf.m) 3. After prestroke actuator installation adjustment, simultaneously stamp both the actuator side and housing side.
----------

----------

0000001701

Test data 108621-0040
(PWM) Pulse width modulation (%) (R) Rack position (mm) Rack sensor output characteristics 1. Rack limit adjustment (1)Measure the rack position R2 for PWM a2%. (2)Confirm that it is within the range R2 = 15+-1 mm. (3)Measure the rack position R1 at PWM a %. (4)Confirm that it is within the range R2 - R1 = 10+-0.1 mm. 2. Check the limp home operation. (1)Move the switch box's limp home switch to the limp home side. (2)Confirm rack position L1 (mm ) and L2 (mm) for PWM in the above table. 3. Check the pull down operation. (1)Confirm that the rack position is 19 mm at PWM B%. (2)In the conditions described in the above table, move the switch box's pull down switch to the pull down side and confirm that the rack position momentarily becomes 1 mm or less.
----------
a1=16.25% a2=72.5% L1=1--mm L2=19++mm A=5% B=95%
----------




Have questions with 108621-0040?





Group cross 108621-0040 ZEXEL

Nissan-Diesel 

 
1680196670 
INJECTION-PUMP ASSEMBLY
PF6TB
F 01G 09U 0E3 
 
INJECTION-PUMP ASSEMBLY
PF6TB

Nissan-Diesel 

9 400 619 080 
1680196676 
INJECTION-PUMP ASSEMBLY
PF6TB
9 400 619 817 
 
INJECTION-PUMP ASSEMBLY
 
 
INJECTION-PUMP ASSEMBLY

Nissan-Diesel 

 
1680196674 
INJECTION-PUMP ASSEMBLY
PF6TB
F 019 Z20 428 
1680196675 
INJECTION-PUMP ASSEMBLY
PF6TB
9 400 613 518 
16801NB003 
INJECTION-PUMP ASSEMBLY
PF6TB
 
 
INJECTION-PUMP ASSEMBLY

Nissan-Diesel 

9 400 611 562 
1680196677 
INJECTION-PUMP ASSEMBLY
PF6TB
9 400 612 726 
 
INJECTION-PUMP ASSEMBLY

Nissan-Diesel 

9 400 619 081 
16801NB001 
INJECTION-PUMP ASSEMBLY
PF6TB
 
 
INJECTION-PUMP ASSEMBLY

Nissan-Diesel 

9 400 619 082 
1680196678 
INJECTION-PUMP ASSEMBLY
PF6HTA
108621-0040  
 
 
INJECTION-PUMP ASSEMBLY

Nissan-Diesel 

9 400 619 083 
1680196679 
INJECTION-PUMP ASSEMBLY
PF6HTB
9 400 611 855 
1680196701 
INJECTION-PUMP ASSEMBLY
PF6TC
9 400 612 727 
16801NB002 
INJECTION-PUMP ASSEMBLY
PF6TC
9 400 619 084 
16801NB004 
INJECTION-PUMP ASSEMBLY
PF6TC
9 400 612 014 
1680196800 
INJECTION-PUMP ASSEMBLY
PF6HTA
9 400 612 185 
16801NB000 
INJECTION-PUMP ASSEMBLY
PF6HTA
F 019 Z10 802 
16801NB00A 
INJECTION-PUMP ASSEMBLY
PF6TB
Back to top