107692-3013 ZEXEL F 01G 09U 0E2 BOSCH INJECTION-PUMP ASSEMBLY f01g09u0e2 1076923013 220008853a


107692-3013 INJECTION-PUMP ASSEMBLY
Rating:
34
Buy INJECTION-PUMP ASSEMBLY 107692-3013 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

BOSCH F 01G 09U 0E2 f01g09u0e2
ZEXEL 107692-3013 1076923013
HINO 220008853A 220008853a

Cross reference number

BOSCH F 01G 09U 0E2 f01g09u0e2
ZEXEL 107692-3013 1076923013
HINO 220008853A 220008853a


Zexel num
Bosch num
Firm num
Name
107692-3013 
107692-3014 
F 01G 09U 0E2 
220008853A  HINO
INJECTION-PUMP ASSEMBLY
M10U-D * K 14CG TICS MD-TI6 TICS

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil
  ISO4113 or {SAEJ967d}
Test oil temperature degC   40 40 45
Nozzle and nozzle holder   105780-8250
Bosch type code   1 688 901 101
Nozzle   105780-0120
Bosch type code   1 688 901 990
Nozzle holder   105780-2190
Opening pressure MPa   20.7
Opening pressure kgf/cm2   211
Injection pipe
Outer diameter - inner diameter - length (mm)
mm   8-3-600
Overflow valve   131425-0920
Overflow valve opening pressure kPa   255 221 289
Overflow valve opening pressure kgf/cm2   2.6 2.25 2.95
Tester oil delivery pressure kPa   255 255 255
Tester oil delivery pressure kgf/cm2   2.6 2.6 2.6
RED3 control unit part number   407910-3 960
RED3 rack sensor specifications mm   19
PS/ACT control unit part no.   407980-2 24*
Digi switch no.   14
Direction of rotation (viewed from drive side)
Right
  R
Injection timing adjustment
Direction of rotation (viewed from drive side)
Right
  R
Injection order   1-4-2-6- 3-5
Pre-stroke mm   6.1 6.07 6.13
Beginning of injection position
Drive side
  NO.1
Difference between angles 1
Cal 1-4
deg.   60 59.75 60.25
Difference between angles 2
Cyl.1-2
deg.   120 119.75 120.25
Difference between angles 3
Cal 1-6
deg.   180 179.75 180.25
Difference between angles 4
Cal 1-3
deg.   240 239.75 240.25
Difference between angles 5
Cal 1-5
deg.   300 299.75 300.25
Injection quantity adjustment
Rack position   (11.7)
Vist V   2.1 2.1 2.1
Pump speed r/min   750 750 750
Average injection quantity mm3/st.   115 113 117
Max. variation between cylinders %   0 -2 2
Basic   *
PS407980-224* V   2.25+-0. 01
PS407980-224* mm   4.1+-0.0 5
Injection quantity adjustment_02
Rack position   (6.2)
Vist V   2.9 2.8 3
Pump speed r/min   480 480 480
Average injection quantity mm3/st.   15 12 18
Max. variation between cylinders %   0 -15 15
PS407980-224* V   V1+0.05+ -0.01
PS407980-224* mm   6+-0.03
Remarks
Refer to items regarding the pre-stroke actuator
 
0000001201
CU407980-224*   *
Actuator retarding type   *
Supply voltage V   24 23.5 24.5
Ambient temperature degC   23 18 28
Pre-stroke mm   3 2.95 3.05
Output voltage V   2.83 2.82 2.84
Adjustment   *
_02
CU407980-224*   *
Supply voltage V   24 23.5 24.5
Ambient temperature degC   23 18 28
Pre-stroke mm   6.1 6.07 6.13
Output voltage V   1.2 1 1.4
Confirmation   *
Remarks
Output voltage V1
 
_03
CU407980-224*   *
Supply voltage V   24 23.5 24.5
Ambient temperature degC   23 18 28
Output voltage V   3.05 3.05
Confirmation of operating range   *

Test data Ex:

Speed control lever angle

Test data 107692-3013
N:Pump normal S:Stop the pump. (1)Rack position = aa (2)Rack position bb
----------
aa=20mm bb=1mm
----------
a=27deg+-5deg b=37deg+-5deg

0000000901

Test data 107692-3013
(1)Pump vertical direction (2)Coupling's key groove position at No 1 cylinder's beginning of injection (3)Pre-stroke: aa (4)-
----------
aa=6.1+-0.03mm
----------
a=(50deg)

Stop lever angle

Test data 107692-3013
(1)Pointer (2)Injection timing aligning mark (3)Fly weight (4)The actual shape and direction may be different from this illustration. Operation sequence 1. Turn the prestroke actuator OFF. 2. Turn the camshaft as far as the No.1 cylinder's beginning of injection position. 3. Check that the pointer alignment mark of the injection pump and the alignment mark of the flywheel are matching. 4. If they are not matching, erase the alignment mark on the flywheel side, and stamp an alignment mark on the flywheel position that matches with the pointer side alignment mark. 5. Check again that the coupling's key groove position is in the No.1 cylinder's beginning of injection position.
----------

----------

0000001301

Test data 107692-3013
A : Stopper pin B: Connector
----------

----------

0000001401

Test data 107692-3013
C:Shim
----------

----------

0000001501

Test data 107692-3013
A:Sealing position B:Pre-stroke actuator 1. When installing the pre-stroke actuator on the pump, first tighten the installation bolts loosely, then move the actuator fully counterclockwise (viewed from the drive side). Temporary tightening torque: 1 - 1.5 N.m (0.1 - 0.15 kgf.m) 2. Move the actuator in the clockwise direction when viewed from the drive side, and adjust so that it becomes the adjustment point of the adjustment value. Then tighten it. Tightening torque: 7^9 N.m (0.7^0.9 kgf.m) 3. After prestroke actuator installation adjustment, simultaneously stamp both the actuator side and housing side.
----------

----------

0000001701

Test data 107692-3013
(Rs) rack sensor specifications (C/U) control unit part number (V) Rack sensor output voltage (R) Rack position (mm) 1. Confirming governor output characteristics (rack 19 mm, span 6 mm) (1)When the output voltages of the rack sensor are V1 and V2, check that the rack positions R1 and R2 in the table above are satisfied.
----------

----------




Have questions with 107692-3013?





Group cross 107692-3013 ZEXEL

Hino 

 
220008850A 
INJECTION-PUMP ASSEMBLY
M10U-D
 
220008851A 
INJECTION-PUMP ASSEMBLY
M10U-D
 
220008852A 
INJECTION-PUMP ASSEMBLY
M10U-D
107692-3013  

107692-3014 
F 01G 09U 0E2 
220008853A 
INJECTION-PUMP ASSEMBLY
M10U-D
9 400 619 062 
220008853B 
INJECTION-PUMP ASSEMBLY
M10U-D
Back to top