107692-0160 ZEXEL INJECTION-PUMP ASSEMBLY Calibration Data 1076920160 16713z5962

Information Cross number Calibration Data Calibration Data Ex

Price: query
Buy now
Add to cart Go to cart

Rating:

Buy INJECTION-PUMP ASSEMBLY 107692-0160 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

ZEXEL 107692-0160 1076920160

NISSAN-DIESEL 16713Z5962 16713z5962

Cross reference number

ZEXEL 107692-0160 1076920160

NISSAN-DIESEL 16713Z5962 16713z5962

Zexel num

Bosch num

Firm num

Name

107692-0160
107692-0280

16713Z5962 NISSAN-DIESEL

INJECTION-PUMP ASSEMBLY
FE6TA * K

Calibration Data:

Adjustment conditions

Test oil
1404 Test oil ISO4113 or {SAEJ967d}

Test oil temperature degC 40 40 45

Nozzle and nozzle holder 105780-8140

Bosch type code EF8511/9A

Nozzle 105780-0000

Bosch type code DN12SD12T

Nozzle holder 105780-2080

Bosch type code EF8511/9

Opening pressure MPa 17.2

Opening pressure kgf/cm2 175

Injection pipe
Outer diameter - inner diameter - length (mm) mm 8-3-600

Overflow valve 134424-4120

Overflow valve opening pressure kPa 255 221 289

Overflow valve opening pressure kgf/cm2 2.6 2.25 2.95

Tester oil delivery pressure kPa 157 157 157

Tester oil delivery pressure kgf/cm2 1.6 1.6 1.6

PS/ACT control unit part no. 407910-3 03*

Selector switch no. 01

PS/ACT control unit part no. 407980-2 24*

Digi switch no. 15

Direction of rotation (viewed from drive side)
Right R

Injection timing adjustment

Direction of rotation (viewed from drive side)
Right R

Injection order 1-4-2-6- 3-5

Pre-stroke mm 5.6 5.57 5.63

Beginning of injection position
Drive side NO.1

Difference between angles 1
Cal 1-4 deg. 60 59.75 60.25

Difference between angles 2
Cyl.1-2 deg. 120 119.75 120.25

Difference between angles 3
Cal 1-6 deg. 180 179.75 180.25

Difference between angles 4
Cal 1-3 deg. 240 239.75 240.25

Difference between angles 5
Cal 1-5 deg. 300 299.75 300.25

Injection quantity adjustment

Adjusting point -

Rack position 11.7

Pump speed r/min 900 900 900

Average injection quantity mm3/st. 83.4 81.4 85.4

Max. variation between cylinders % 0 -4 4

Basic *

Fixing the rack *

PS407980-224* V 2.25+-0. 01

PS407980-224* mm 3.6+-0.0 3

PS407910-303* V 2.25+-0. 01

PS407910-303* mm 3.6+-0.0 3

Standard for adjustment of the maximum variation between cylinders *

Injection quantity adjustment_02

Adjusting point Z

Rack position 7.8+-0.5

Pump speed r/min 750 750 750

Average injection quantity mm3/st. 9.5 7.7 11.3

Max. variation between cylinders % 0 -10 10

Fixing the rack *

PS407980-224* V 2.25+-0. 01

PS407980-224* mm 3.6+-0.0 3

PS407910-303* V 2.25+-0. 01

PS407910-303* mm 3.6+-0.0 3

Standard for adjustment of the maximum variation between cylinders *

Injection quantity adjustment_03

Adjusting point A

Rack position R1(11.7)

Pump speed r/min 900 900 900

Average injection quantity mm3/st. 83.4 82.4 84.4

Basic *

Fixing the lever *

Boost pressure kPa 86.6 86.6

Boost pressure mmHg 650 650

PS407980-224* V 2.25+-0. 01

PS407980-224* mm 3.6+-0.0 3

PS407910-303* V 2.25+-0. 01

PS407910-303* mm 3.6+-0.0 3

Injection quantity adjustment_04

Adjusting point B

Rack position R1+2.05

Pump speed r/min 1400 1400 1400

Average injection quantity mm3/st. 105.8 103.8 107.8

Fixing the lever *

Boost pressure kPa 86.6 86.6

Boost pressure mmHg 650 650

PS407980-224* V 2.25+-0. 01

PS407980-224* mm 3.6+-0.0 3

PS407910-303* V 2.25+-0. 01

PS407910-303* mm 3.6+-0.0 3

Injection quantity adjustment_05

Adjusting point C

Rack position R2(R1-1. 65)

Pump speed r/min 700 700 700

Average injection quantity mm3/st. 53 52 54

Fixing the lever *

Boost pressure kPa 0 0 0

Boost pressure mmHg 0 0 0

PS407980-224* V 2.25+-0. 01

PS407980-224* mm 3.6+-0.0 3

PS407910-303* V 2.25+-0. 01

PS407910-303* mm 3.6+-0.0 3

Boost compensator adjustment

Pump speed r/min 700 700 700

Rack position R2(R1-1. 65)

Boost pressure kPa 24 20 28

Boost pressure mmHg 180 150 210

Boost compensator adjustment_02

Pump speed r/min 700 700 700

Rack position R2+0.6

Boost pressure kPa 40 38.7 41.3

Boost pressure mmHg 300 290 310

Boost compensator adjustment_03

Pump speed r/min 700 700 700

Rack position R1-0.35

Boost pressure kPa 73.3 73.3 73.3

Boost pressure mmHg 550 550 550

0000001601

CU407980-224* *

Actuator retarding type *

Supply voltage V 12 11.5 12.5

Ambient temperature degC 23 18 28

Pre-stroke mm 2.5 2.45 2.55

Output voltage V 2.83 2.82 2.84

Adjustment *

_02

CU407980-224* *

Supply voltage V 12 11.5 12.5

Ambient temperature degC 23 18 28

Pre-stroke mm 5.6 5.57 5.63

Output voltage V 1.2 1 1.4

Confirmation *

_03

CU407980-224* *

Supply voltage V 12 11.5 12.5

Ambient temperature degC 23 18 28

Output voltage V 3.05 3.05

Confirmation of operating range *

_04

CU407910-303* *

Actuator retarding type *

Supply voltage V 12 11.5 12.5

Ambient temperature degC 23 18 28

Pre-stroke mm 2.5 2.45 2.55

Output voltage V 2.83 2.82 2.84

Adjustment *

_05

CU407910-303* *

Supply voltage V 12 11.5 12.5

Ambient temperature degC 23 18 28

Pre-stroke mm 5.6 5.57 5.63

Output voltage V 1.2 1 1.4

Confirmation *

_06

CU407910-303* *

Supply voltage V 12 11.5 12.5

Ambient temperature degC 23 18 28

Output voltage V 3.05 3.05

Confirmation of operating range *

Test data Ex:

Governor adjustment

N:Pump speed R:Rack position (mm) (1)Torque cam stamping: T1 (2)Tolerance for racks not indicated: +-0.05mm. (3)Boost compensator stroke: BCL
----------
T1=G52 BCL=(1.3)+-0.1mm
----------

Speed control lever angle

F:Full speed I:Idle (1)Stopper bolt setting (2)-
----------

----------
a=25.5deg+-5deg b=41.5deg+-3deg

Stop lever angle

N:Pump normal S:Stop the pump. (1)- (2)Set the stopper bolt at speed = aa and rack position = bb and confirm non-injection.
----------
aa=1400r/min bb=4.3-0.5mm
----------
a=25deg+-5deg b=38.5deg+-5deg

0000001301

(1)Pump vertical direction (2)Coupling's key groove position at No 1 cylinder's beginning of injection (3)Pre-stroke: aa (4)-
----------
aa=5.6+-0.03mm
----------
a=(20deg)

0000001401

(1)Pointer (2)Injection timing aligning mark (3)Fly weight (4)The actual shape and direction may be different from this illustration. Operation sequence 1. Turn the prestroke actuator OFF. 2. Turn the camshaft as far as the No.1 cylinder's beginning of injection position. 3. Check that the pointer alignment mark of the injection pump and the alignment mark of the flywheel are matching. 4. If they are not matching, erase the alignment mark on the flywheel side, and stamp an alignment mark on the flywheel position that matches with the pointer side alignment mark. 5. Check again that the coupling's key groove position is in the No.1 cylinder's beginning of injection position.
----------

----------

0000001701

A : Stopper pin B: Connector
----------

----------

0000001801

C:Shim
----------

----------

0000001901

A:Sealing position B:Pre-stroke actuator 1. When installing the pre-stroke actuator on the pump, first tighten the installation bolts loosely, then move the actuator fully counterclockwise (viewed from the drive side). Temporary tightening torque: 1 - 1.5 N.m (0.1 - 0.15 kgf.m) 2. Move the actuator in the clockwise direction when viewed from the drive side, and adjust so that it becomes the adjustment point of the adjustment value. Then tighten it. Tightening torque: 7^9 N.m (0.7^0.9 kgf.m) 3. After prestroke actuator installation adjustment, simultaneously stamp both the actuator side and housing side.
----------

----------

0000002201 RACK SENSOR

(VR) measurement voltage (I) Part number of the control unit (G) Apply red paint. (H): End surface of the pump 1. Rack sensor adjustment (-0620) (1)Fix the speed control lever at the full position (2)Set the speed to N1 r/min. (If the boost compensator is provided, apply boost pressure.) (3)Adjust the bobbin (A) so that the rack sensor's output voltage is VR+-0.01. (4)At that time, rack position must be Ra. (5)Apply G at two places. Connecting part between the joint (B) and the nut (F) Connecting part between the joint (B) and the end surface of the pump (H)
----------
N1=1400r/min Ra=R1(11.7)+2.05mm
----------

0000002301 SPEED SENSOR

(A) Flyweight projection (B) Pickup sensor (c) Lock nut Speed sensor installation (1)Install the speed sensor so that the clearance between the sensor and the flyweight projection is L. (This gap is the gap when the pickup sensor is returned 1 turn from where it contacts the flyweight tooth.)
----------
L=0.8~1mm
----------

0000002401 MICRO SWITCH

Adjustment of the micro-switch Adjust the bolt to obtain the following lever position when the micro-switch is ON. (1)Speed N1 (2)Rack position Ra
----------
N1=375r/min Ra=7.8+-0.1mm
----------