107691-3760 ZEXEL F 019 Z10 909 BOSCH INJECTION-PUMP ASSEMBLY f019z10909 1076913760 220402560a


107691-3760 INJECTION-PUMP ASSEMBLY
Rating:
44
Buy INJECTION-PUMP ASSEMBLY 107691-3760 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

BOSCH F 019 Z10 909 f019z10909
ZEXEL 107691-3760 1076913760
HINO 220402560A 220402560a

Service parts 107691-3760 INJECTION-PUMP ASSEMBLY:

1. _
2. FUEL INJECTION PUMP 107069-0730
3. GOVERNOR 105933-1870
4. SUPPLY PUMP 105237-6480
5. AUTOM. ADVANCE MECHANIS 105681-6120
6. COUPLING PLATE 105664-2630
7. COUPLING PLATE
9. _
10. NOZZLE AND HOLDER ASSY 105160-4892
11. Nozzle and Holder 236003210C
12. Open Pre:MPa(Kqf/cm2) 21.6(220)
13. NOZZLE-HOLDER 105030-3680
14. NOZZLE 105025-1940
15. NOZZLE SET

Include in #1:

107691-3760 as INJECTION-PUMP ASSEMBLY

Cross reference number

BOSCH F 019 Z10 909 f019z10909
ZEXEL 107691-3760 1076913760
HINO 220402560A 220402560a


Zexel num
Bosch num
Firm num
Name
107691-3760 
F 019 Z10 909 
220402560A  HINO
INJECTION-PUMP ASSEMBLY
J08C-TV K 14CG INJECTION PUMP ASSY TICS MD-TI6 TICS
107691-3760 
F 019 Z10 909 
S220402560A  HINO
INJECTION-PUMP ASSEMBLY
J08C-TV A K 14CG INJECTION PUMP ASSY TICS MD-TI6 TICS

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil
  ISO4113 or {SAEJ967d}
Test oil temperature degC   40 40 45
Nozzle and nozzle holder   105780-8250
Bosch type code   1 688 901 101
Nozzle   105780-0120
Bosch type code   1 688 901 990
Nozzle holder   105780-2190
Opening pressure MPa   20.7
Opening pressure kgf/cm2   211
Injection pipe
Outer diameter - inner diameter - length (mm)
mm   8-3-600
Overflow valve   131425-0920
Overflow valve opening pressure kPa   255 221 289
Overflow valve opening pressure kgf/cm2   2.6 2.25 2.95
Tester oil delivery pressure kPa   255 255 255
Tester oil delivery pressure kgf/cm2   2.6 2.6 2.6
PS/ACT control unit part no.   407980-2 24*
Digi switch no.   17
Direction of rotation (viewed from drive side)
Left
  L
Injection timing adjustment
Direction of rotation (viewed from drive side)
Left
  L
Injection order   1-4-2-6- 3-5
Pre-stroke mm   5.1 5.07 5.13
Beginning of injection position
Governor side
  NO.1
Difference between angles 1
Cal 1-4
deg.   60 59.75 60.25
Difference between angles 2
Cyl.1-2
deg.   120 119.75 120.25
Difference between angles 3
Cal 1-6
deg.   180 179.75 180.25
Difference between angles 4
Cal 1-3
deg.   240 239.75 240.25
Difference between angles 5
Cal 1-5
deg.   300 299.75 300.25
Injection quantity adjustment
Adjusting point   -
Rack position   11.7
Pump speed r/min   750 750 750
Average injection quantity mm3/st.   115.5 112.5 118.5
Max. variation between cylinders %   0 -2 2
Basic   *
Fixing the rack   *
PS407980-224* V   2.25+-0. 01
PS407980-224* mm   3.1+-0.0 5
Standard for adjustment of the maximum variation between cylinders   *
Injection quantity adjustment_02
Adjusting point   Z
Rack position   6.3+-0.5
Pump speed r/min   485 485 485
Average injection quantity mm3/st.   9 8 10
Max. variation between cylinders %   0 -15 15
Fixing the rack   *
PS407980-224* V   V1+0.05+ -0.01
PS407980-224* mm   5+-0.03
Standard for adjustment of the maximum variation between cylinders   *
Remarks
Refer to items regarding the pre-stroke actuator
 
Injection quantity adjustment_03
Adjusting point   A
Rack position   R1(11.7)
Pump speed r/min   750 750 750
Average injection quantity mm3/st.   115.5 113.5 117.5
Basic   *
Fixing the lever   *
Boost pressure kPa   63.3 63.3
Boost pressure mmHg   475 475
PS407980-224* V   2.25+-0. 01
PS407980-224* mm   3.1+-0.0 5
Injection quantity adjustment_04
Adjusting point   B
Rack position   R1+2.55
Pump speed r/min   1250 1250 1250
Average injection quantity mm3/st.   127.5 121.5 133.5
Fixing the lever   *
Boost pressure kPa   63.3 63.3
Boost pressure mmHg   475 475
PS407980-224* V   2.25+-0. 01
PS407980-224* mm   3.1+-0.0 5
Boost compensator adjustment
Pump speed r/min   350 350 350
Rack position   R2-1.1
Boost pressure kPa   36.7 35.4 38
Boost pressure mmHg   275 265 285
Boost compensator adjustment_02
Pump speed r/min   350 350 350
Rack position   R2(R1-1. 4)
Boost pressure kPa   50 50 50
Boost pressure mmHg   375 375 375
Timer adjustment
Pump speed r/min   1165--
Advance angle deg.   0 0 0
Remarks
Start
 
Timer adjustment_02
Pump speed r/min   1115
Advance angle deg.   0 0 0
Remarks
Pointer stamping position
 
Timer adjustment_03
Pump speed r/min   1115
Advance angle deg.   0 -0.3 0
Timer adjustment_04
Pump speed r/min   1275
Advance angle deg.   -1.5 -1.8 -1.2
Remarks
Finish
 
0000001601
CU407980-224*   *
Actuator retarding type   *
Supply voltage V   24 23.5 24.5
Ambient temperature degC   23 18 28
Pre-stroke mm   2 1.95 2.05
Output voltage V   2.83 2.82 2.84
Adjustment   *
_02
CU407980-224*   *
Supply voltage V   24 23.5 24.5
Ambient temperature degC   23 18 28
Pre-stroke mm   5.1 5.07 5.13
Output voltage V   1.2 1 1.4
Confirmation   *
Remarks
Output voltage V1
 
_03
CU407980-224*   *
Supply voltage V   24 23.5 24.5
Ambient temperature degC   23 18 28
Output voltage V   3.05 3.05
Confirmation of operating range   *

Test data Ex:

Governor adjustment

Test data 107691-3760
N:Pump speed R:Rack position (mm) (1)Torque cam stamping: T1 (2)Tolerance for racks not indicated: +-0.05mm. (3)When setting the stop lever after governor adjustment, confirm that rack position Ra (point B) can be obtained at the full setting. (4)Stop lever's normal position setting: RA (5)Boost compensator stroke: BCL
----------
T1=AH48 Ra=R1+2.55mm RA=(18)mm BCL=1.1+-0.1mm
----------

Speed control lever angle

Test data 107691-3760
F:Full speed I:Idle (1)Use the hole at R = aa (2)Stopper bolt set position 'H'
----------
aa=44mm
----------
a=10deg+-5deg b=(39deg)+-3deg

Stop lever angle

Test data 107691-3760
N:Pump normal S:Stop the pump. (1)Use the hole at R = aa (2)Speed = bb, rack position = cc (3)Set the stopper bolt at rack position = dd
----------
aa=40mm bb=0r/min cc=1.5+-0.1mm dd=(18)mm
----------
a=15deg+-5deg b=35deg+-5deg

0000001301

Test data 107691-3760
(1)Pump vertical direction (2)Coupling's key groove position at No 1 cylinder's beginning of injection (3)Pre-stroke: aa (4)-
----------
aa=5.1+-0.03mm
----------
a=(20deg)

0000001401

Test data 107691-3760
(1)Pointer (2)Injection timing aligning mark (3)Fly weight (4)The actual shape and direction may be different from this illustration. Operation sequence 1. Turn the prestroke actuator OFF. 2. Turn the camshaft as far as the No.1 cylinder's beginning of injection position. 3. Check that the pointer alignment mark of the injection pump and the alignment mark of the flywheel are matching. 4. If they are not matching, erase the alignment mark on the flywheel side, and stamp an alignment mark on the flywheel position that matches with the pointer side alignment mark. 5. Check again that the coupling's key groove position is in the No.1 cylinder's beginning of injection position.
----------

----------

0000001701

Test data 107691-3760
A : Stopper pin B: Connector
----------

----------

0000001801

Test data 107691-3760
C:Shim
----------

----------

0000001901

Test data 107691-3760
A:Sealing position B:Pre-stroke actuator 1. When installing the pre-stroke actuator on the pump, first tighten the installation bolts loosely, then move the actuator fully clockwise (viewed from the drive side). Temporary tightening torque: 1 - 1.5 N.m (0.1 - 0.15 kgf.m) 2. Move the actuator in the counterclockwise direction when viewed from the drive side, and adjust so that it becomes the adjustment point of the adjustment value. Then tighten it. Tightening torque: 7^9 N.m (0.7^0.9 kgf.m) 3. After prestroke actuator installation adjustment, simultaneously stamp both the actuator side and housing side.
----------

----------

0000002201 RACK SENSOR

Test data 107691-3760
G:Red paint H:Pump end face P/N: part number of suitable shim (1)Threaded type rack block (2)Welded type rack block Rack sensor adjustment 1. Threaded type rack sensor (-5*20, P type, no TICS rack limit). (1)Screw in the bobbin (A) until it contacts the joint (B). (2)Fix the pump lever. (3)At speed N1 and rack position Ra, adjust the amount that the bobbin is screwed in so that the amp's output voltage is V1. (4)Fix using the nut (F). (5)Affix the caution plate to the upper part of the joint (B). (6)Apply (G) at two places. Connecting part between the joint (B) and the nut (F) Connecting part between the end surface of the pump (H) and the joint (B) 2. Range for screw-in adjustment between the bobbin (A) and the joint (B) is 9 threads. Screw in to the end from (the position where the bobbin (A) is rotated 9 turns). Speed N1, rack position Ra, output voltage V1, rack sensor supply voltage 5+-0.01 (V)
----------
Ra=R1(11.7)+2.55mm N1=1250r/min V1=3+-0.01V
----------




Have questions with 107691-3760?





Group cross 107691-3760 ZEXEL

Hino 

 
220402330B 
INJECTION-PUMP ASSEMBLY
J08C-UL
9 400 618 979 
220402331B 
INJECTION-PUMP ASSEMBLY
J08C-UL
9 400 618 979 
S220402331B 
INJECTION-PUMP ASSEMBLY
J08C-UL
 
22010E0680 
INJECTION-PUMP ASSEMBLY
J08C-UL
 
220402510A 
INJECTION-PUMP ASSEMBLY
J08C-UR
9 400 618 980 
220402511A 
INJECTION-PUMP ASSEMBLY
J08C-UR
 
220402520A 
INJECTION-PUMP ASSEMBLY
J08C-US
9 400 618 981 
220402521A 
INJECTION-PUMP ASSEMBLY
J08C-US
 
220402540A 
INJECTION-PUMP ASSEMBLY
J08C-UK
 
220402541A 
INJECTION-PUMP ASSEMBLY
J08C-UK
F 019 Z10 800 
220402570A 
INJECTION-PUMP ASSEMBLY
J08C-UK
9 400 619 902 
220402530A 
INJECTION-PUMP ASSEMBLY
J08C-TI
9 400 619 902 
S220402530 
INJECTION-PUMP ASSEMBLY
J08C-TI
 
220402550A 
INJECTION-PUMP ASSEMBLY
J08C-TR
F 019 Z10 801 
220402551A 
INJECTION-PUMP ASSEMBLY
J08C-TR
F 019 Z10 801 
S220402551A 
INJECTION-PUMP ASSEMBLY
J08C-TR
107691-3760  
F 019 Z10 909 
220402560A 
INJECTION-PUMP ASSEMBLY
J08C-TV
107691-3760  
F 019 Z10 909 
S220402560A 
INJECTION-PUMP ASSEMBLY
J08C-TV
Back to top