107691-3580 ZEXEL 9 400 618 975 BOSCH INJECTION-PUMP ASSEMBLY 9400618975 1076913580 220402451b


107691-3580 INJECTION-PUMP ASSEMBLY
Rating:
8
Buy INJECTION-PUMP ASSEMBLY 107691-3580 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

BOSCH 9 400 618 975 9400618975
ZEXEL 107691-3580 1076913580
HINO 220402451B 220402451b

Service parts 107691-3580 INJECTION-PUMP ASSEMBLY:

1. _
2. FUEL INJECTION PUMP 107069-0750
3. GOVERNOR 105962-0220
4. SUPPLY PUMP 105237-6480
5. AUTOM. ADVANCE MECHANIS 105681-6130
6. COUPLING PLATE 105664-2630
7. COUPLING PLATE
9. _
10. NOZZLE AND HOLDER ASSY 105101-8422
11. Nozzle and Holder 23600-3222B
12. Open Pre:MPa(Kqf/cm2) 17.7{180}/21.6{220}
13. NOZZLE-HOLDER 105030-3700
14. NOZZLE
15. NOZZLE SET 105019-2170

Include in #1:

107691-3580 as INJECTION-PUMP ASSEMBLY

Cross reference number

BOSCH 9 400 618 975 9400618975
ZEXEL 107691-3580 1076913580
HINO 220402451B 220402451b


Zexel num
Bosch num
Firm num
Name
107691-3580 
9 400 618 975 
220402451B  HINO
INJECTION-PUMP ASSEMBLY
J08C-UK K 14CG INJECTION PUMP ASSY TICS MD-TI6 TICS
107691-3580 
9 400 618 975 
S220402451  HINO
INJECTION-PUMP ASSEMBLY
J08C-UK A K 14CG INJECTION PUMP ASSY TICS MD-TI6 TICS
107691-3580 
9 400 618 975 
S220402451B  HINO
INJECTION-PUMP ASSEMBLY
J08C-UK B K 14CG INJECTION PUMP ASSY TICS MD-TI6 TICS

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil
  ISO4113 or {SAEJ967d}
Test oil temperature degC   40 40 45
Nozzle and nozzle holder   105780-8250
Bosch type code   1 688 901 101
Nozzle   105780-0120
Bosch type code   1 688 901 990
Nozzle holder   105780-2190
Opening pressure MPa   20.7
Opening pressure kgf/cm2   211
Injection pipe
Outer diameter - inner diameter - length (mm)
mm   8-3-600
Overflow valve   131425-0920
Overflow valve opening pressure kPa   255 221 289
Overflow valve opening pressure kgf/cm2   2.6 2.25 2.95
Tester oil delivery pressure kPa   255 255 255
Tester oil delivery pressure kgf/cm2   2.6 2.6 2.6
RED4 control unit part number   407915-0 590
RED4 rack sensor specifications mm   19
PS/ACT control unit part no.   407980-2 24*
Digi switch no.   17
Direction of rotation (viewed from drive side)
Left
  L
Injection timing adjustment
Direction of rotation (viewed from drive side)
Left
  L
Injection order   1-4-2-6- 3-5
Pre-stroke mm   5.1 5.07 5.13
Beginning of injection position
Governor side
  NO.1
Difference between angles 1
Cal 1-4
deg.   60 59.75 60.25
Difference between angles 2
Cyl.1-2
deg.   120 119.75 120.25
Difference between angles 3
Cal 1-6
deg.   180 179.75 180.25
Difference between angles 4
Cal 1-3
deg.   240 239.75 240.25
Difference between angles 5
Cal 1-5
deg.   300 299.75 300.25
Injection quantity adjustment
Rack position   (11.8)
PWM %   54.5
Pump speed r/min   750 750 750
Average injection quantity mm3/st.   123.5 121.5 125.5
Max. variation between cylinders %   0 -3.5 3.5
Basic   *
PS407980-224* V   2.25+-0. 01
PS407980-224* mm   3.1+-0.0 5
Injection quantity adjustment_02
Rack position   (6.8)
PWM %   26.3+-2. 8
Pump speed r/min   440 440 440
Each cylinder's injection qty mm3/st.   11 9.9 12.1
PS407980-224* V   V1+0.05+ -0.01
PS407980-224* mm   5+-0.03
Remarks
Refer to items regarding the pre-stroke actuator
 
Governor adjustment
Pump speed r/min   1220--
Advance angle deg.   0 0 0
Remarks
Start
 
Governor adjustment_02
Pump speed r/min   1170
Advance angle deg.   0 0 0
Remarks
Pointer stamping position
 
Governor adjustment_03
Pump speed r/min   1170
Advance angle deg.   0 -0.3 0
Governor adjustment_04
Pump speed r/min   1320-50
Advance angle deg.   -1.5 -1.8 -1.2
Remarks
Finish
 
0000001201
CU407980-224*   *
Actuator advancing type   *
Supply voltage V   24 23.5 24.5
Ambient temperature degC   23 18 28
Pre-stroke mm   2 1.95 2.05
Output voltage V   2.83 2.82 2.84
Adjustment   *
_02
CU407980-224*   *
Supply voltage V   24 23.5 24.5
Ambient temperature degC   23 18 28
Pre-stroke mm   5.1 5.07 5.13
Output voltage V   1.2 1 1.4
Confirmation   *
Remarks
Output voltage V1
 
_03
CU407980-224*   *
Supply voltage V   24 23.5 24.5
Ambient temperature degC   23 18 28
Output voltage V   3.05 3.05
Confirmation of operating range   *

Test data Ex:

Speed control lever angle

Test data 107691-3580
N:Pump normal S:Stop the pump. (1)Rack position = aa (2)Rack position bb
----------
aa=1mm bb=20mm
----------
a=18.5deg+-5deg b=37deg+-5deg

0000000901

Test data 107691-3580
(1)Pump vertical direction (2)Coupling's key groove position at No 1 cylinder's beginning of injection (3)B.T.D.C.: aa (4)Pre-stroke: bb
----------
aa=3deg bb=5.1+-0.03mm
----------
a=(20deg)

Stop lever angle

Test data 107691-3580
(1)Pointer (2)Injection timing aligning mark (3)Fly weight (4)The actual shape and direction may be different from this illustration. Operation sequence 1. Turn the prestroke actuator OFF. 2. Turn the camshaft as far as the No.1 cylinder's beginning of injection position. 3. Check that the pointer alignment mark of the injection pump and the alignment mark of the flywheel are matching. 4. If they are not matching, erase the alignment mark on the flywheel side, and stamp an alignment mark on the flywheel position that matches with the pointer side alignment mark. 5. Check again that the coupling's key groove position is in the No.1 cylinder's beginning of injection position.
----------

----------

0000001301

Test data 107691-3580
A : Stopper pin B: Connector
----------

----------

0000001401

Test data 107691-3580
C:Shim
----------

----------

0000001501

Test data 107691-3580
A:Sealing position B:Pre-stroke actuator 1. When installing the pre-stroke actuator on the pump, first tighten the installation bolts loosely, then move the actuator fully clockwise (viewed from the drive side). Temporary tightening torque: 1 - 1.5 N.m (0.1 - 0.15 kgf.m) 2. Move the actuator in the counterclockwise direction when viewed from the drive side, and adjust so that it becomes the adjustment point of the adjustment value. Then tighten it. Tightening torque: 7^9 N.m (0.7^0.9 kgf.m) 3. After prestroke actuator installation adjustment, simultaneously stamp both the actuator side and housing side.
----------

----------

0000001701

Test data 107691-3580
(PWM) Pulse width modulation (%) (R) Rack position (mm) Rack sensor output characteristics 1. Rack limit adjustment (1)Measure the rack position R2 for PWM a2%. (2)Confirm that it is within the range R2 = 15+-1 mm. (3)Measure the rack position R1 at PWM a %. (4)Confirm that it is within the range R2 - R1 = 10+-0.1 mm. 2. Check the limp home operation. (1)Move the switch box's limp home switch to the limp home side. (2)Confirm rack position L1 (mm ) and L2 (mm) for PWM in the above table. 3. Check the pull down operation. (1)Confirm that the rack position is 19 mm at PWM B%. (2)In the conditions described in the above table, move the switch box's pull down switch to the pull down side and confirm that the rack position momentarily becomes 1 mm or less.
----------
a1=16.25% a2=72.5% L1=1--mm L2=19++mm A=5 % B=95%
----------




Have questions with 107691-3580?





Group cross 107691-3580 ZEXEL

Hino 

9 400 612 387 
220402160A 
INJECTION-PUMP ASSEMBLY
J08C-TT
9 400 612 387 
S220402160A 
INJECTION-PUMP ASSEMBLY
J08C-TT
9 400 612 388 
220402200A 
INJECTION-PUMP ASSEMBLY
J08C-TW
9 400 612 388 
S220402200A 
INJECTION-PUMP ASSEMBLY
J08C-TW
9 400 618 972 
220402210A 
INJECTION-PUMP ASSEMBLY
J08C-TT
9 400 618 972 
S220402210A 
INJECTION-PUMP ASSEMBLY
J08C-TT
9 400 618 973 
220402220A 
INJECTION-PUMP ASSEMBLY
J08C-TT
9 400 618 973 
S220402220A 
INJECTION-PUMP ASSEMBLY
J08C-TT
F 01G 09U 1BF 
22010E0360 
INJECTION-PUMP ASSEMBLY
J08C-TT
9 400 612 716 
220402230A 
INJECTION-PUMP ASSEMBLY
J08C
9 400 612 717 
220402232A 
INJECTION-PUMP ASSEMBLY
J08C
9 400 618 974 
220402233B 
INJECTION-PUMP ASSEMBLY
J08C-S
 
220402240A 
INJECTION-PUMP ASSEMBLY
J08C
9 400 612 796 
220402242A 
INJECTION-PUMP ASSEMBLY
J08C
9 400 613 075 
220402243B 
INJECTION-PUMP ASSEMBLY
J08C-T
 
220402251B 
INJECTION-PUMP ASSEMBLY
J08C-TV
9 400 613 312 
220402251C 
INJECTION-PUMP ASSEMBLY
J08C-TV
9 400 613 449 
220402252A 
INJECTION-PUMP ASSEMBLY
J08C-TV
9 400 613 449 
S220402252A 
INJECTION-PUMP ASSEMBLY
J08C-TV
9 400 613 281 
220402341B 
INJECTION-PUMP ASSEMBLY
J08C-UJ
9 400 613 450 
220402342A 
INJECTION-PUMP ASSEMBLY
J08C-UJ
9 400 613 450 
S220402342A 
INJECTION-PUMP ASSEMBLY
J08C-UJ
107691-3580  
9 400 618 975 
220402451B 
INJECTION-PUMP ASSEMBLY
J08C-UK
107691-3580  
9 400 618 975 
S220402451 
INJECTION-PUMP ASSEMBLY
J08C-UK
107691-3580  
9 400 618 975 
S220402451B 
INJECTION-PUMP ASSEMBLY
J08C-UK
9 400 613 282 
220402351B 
INJECTION-PUMP ASSEMBLY
J08C-UK
9 400 613 451 
220402352B 
INJECTION-PUMP ASSEMBLY
J08C-UK
Back to top