107492-2170 ZEXEL 9 400 618 857 BOSCH INJECTION-PUMP ASSEMBLY 9400618857 1074922170


107492-2170 INJECTION-PUMP ASSEMBLY
Rating:
76
Buy INJECTION-PUMP ASSEMBLY 107492-2170 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

BOSCH 9 400 618 857 9400618857
ZEXEL 107492-2170 1074922170

Service parts 107492-2170 INJECTION-PUMP ASSEMBLY:

1. _
2. FUEL INJECTION PUMP 107049-3110
3. GOVERNOR 105956-0160
4. SUPPLY PUMP 105237-6360
5. AUTOM. ADVANCE MECHANIS
6. COUPLING PLATE
7. COUPLING PLATE 156639-8021
9. _
10. NOZZLE AND HOLDER ASSY 105118-6590
11. Nozzle and Holder ME015202
12. Open Pre:MPa(Kqf/cm2) 21.6{220}
13. NOZZLE-HOLDER 105048-4160
14. NOZZLE 105017-1221
15. NOZZLE SET

Include in #1:

107492-2170 as INJECTION-PUMP ASSEMBLY

Cross reference number

BOSCH 9 400 618 857 9400618857
ZEXEL 107492-2170 1074922170


Zexel num
Bosch num
Firm num
Name
107492-2170 
107492-2171 
9 400 618 857 
   
INJECTION-PUMP ASSEMBLY
4D34T3 * K 14CF TICS MD-TI4 TICS

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil
  ISO4113 or {SAEJ967d}
Test oil temperature degC   40 40 45
Nozzle and nozzle holder   105780-8250
Bosch type code   1 688 901 101
Nozzle   105780-0120
Bosch type code   1 688 901 990
Nozzle holder   105780-2190
Opening pressure MPa   20.7
Opening pressure kgf/cm2   211
Injection pipe
Outer diameter - inner diameter - length (mm)
mm   8-3-600
Overflow valve   131425-0520
Overflow valve opening pressure kPa   255 221 289
Overflow valve opening pressure kgf/cm2   2.6 2.25 2.95
Tester oil delivery pressure kPa   255 255 255
Tester oil delivery pressure kgf/cm2   2.6 2.6 2.6
RED3 control unit part number   407910-3 960
RED3 rack sensor specifications mm   19
PS/ACT control unit part no.   407980-2 24*
Digi switch no.   03
Direction of rotation (viewed from drive side)
Right
  R
Injection timing adjustment
Direction of rotation (viewed from drive side)
Right
  R
Injection order   1-3-4-2
Pre-stroke mm   5.1 5.07 5.13
Beginning of injection position
Drive side
  NO.1
Difference between angles 1
Cal 1-3
deg.   90 89.75 90.25
Difference between angles 2
Cal 1-4
deg.   180 179.75 180.25
Difference between angles 3
Cyl.1-2
deg.   270 269.75 270.25
Injection quantity adjustment
Rack position   (9.9)
Vist V   2.36 2.36 2.36
Pump speed r/min   800 800 800
Average injection quantity mm3/st.   114.5 113.5 115.5
Max. variation between cylinders %   0 -3 3
Basic   *
PS407980-224* V   2.25+-0. 01
PS407980-224* mm   3.1+-0.0 5
Injection quantity adjustment_02
Rack position   (6.1)
Vist V   2.9 2.8 3
Pump speed r/min   475 475 475
Average injection quantity mm3/st.   16 14.5 17.5
Max. variation between cylinders %   0 -15 15
PS407980-224* V   V1+0.05+ -0.01
PS407980-224* mm   5+-0.03
Remarks
Refer to items regarding the pre-stroke actuator
 
0000001201
CU407980-224*   *
Actuator retarding type   *
Supply voltage V   24 23.5 24.5
Ambient temperature degC   23 18 28
Pre-stroke mm   2 1.95 2.05
Output voltage V   2.83 2.82 2.84
Adjustment   *
_02
CU407980-224*   *
Supply voltage V   24 23.5 24.5
Ambient temperature degC   23 18 28
Pre-stroke mm   5.1 5.07 5.13
Output voltage V   1.2 1 1.4
Confirmation   *
Remarks
Output voltage V1
 
_03
CU407980-224*   *
Supply voltage V   24 23.5 24.5
Ambient temperature degC   23 18 28
Output voltage V   3.05 3.05
Confirmation of operating range   *

Test data Ex:

Speed control lever angle

Test data 107492-2170
N:Pump normal S:Stop the pump. (1)Rack position = aa (2)Rack position bb
----------
aa=1mm bb=20mm
----------
a=57deg+-5deg b=37deg+-5deg

0000000901

Test data 107492-2170
(1)Pump vertical direction (2)Position of gear mark '3' at No 1 cylinder's beginning of injection (3)B.T.D.C.: aa (4)Pre-stroke: bb
----------
aa=3deg bb=5.1+-0.03mm
----------
a=(130deg)

Stop lever angle

Test data 107492-2170
(1)Pointer (2)Injection timing aligning mark (3)Fly weight (4)The actual shape and direction may be different from this illustration. Operation sequence 1. Turn the prestroke actuator OFF. 2. Turn the camshaft as far as the No.1 cylinder's beginning of injection position. 3. Check that the pointer alignment mark of the injection pump and the alignment mark of the flywheel are matching. 4. If they are not matching, erase the alignment mark on the flywheel side, and stamp an alignment mark on the flywheel position that matches with the pointer side alignment mark. 5. Check again that the coupling's key groove position is in the No.1 cylinder's beginning of injection position.
----------

----------

0000001301

Test data 107492-2170
A : Stopper pin B: Connector
----------

----------

0000001401

Test data 107492-2170
C:Shim
----------

----------

0000001501

Test data 107492-2170
A:Sealing position B:Pre-stroke actuator 1. When installing the pre-stroke actuator on the pump, first tighten the installation bolts loosely, then move the actuator fully counterclockwise (viewed from the drive side). Temporary tightening torque: 1 - 1.5 N.m (0.1 - 0.15 kgf.m) 2. Move the actuator in the clockwise direction when viewed from the drive side, and adjust so that it becomes the adjustment point of the adjustment value. Then tighten it. Tightening torque: 7^9 N.m (0.7^0.9 kgf.m) 3. After prestroke actuator installation adjustment, simultaneously stamp both the actuator side and housing side.
----------

----------

0000001701

Test data 107492-2170
(Rs) rack sensor specifications (C/U) control unit part number (V) Rack sensor output voltage (R) Rack position (mm) 1. Confirming governor output characteristics (rack 19 mm, span 6 mm) (1)When the output voltages of the rack sensor are V1 and V2, check that the rack positions R1 and R2 in the table above are satisfied.
----------

----------

0000001901 RACK SENSOR

Test data 107492-2170
(VR) measurement voltage (I) Part number of the control unit (G) Apply red paint. (H): End surface of the pump 1. Rack sensor adjustment (154610-0620) (1)At governor side rack sensor output voltage V1, adjust the bobbin (A) so that the drive side rack sensor output voltage is VR+-0.01. (2)Apply G at two places. Connecting part between the joint (B) and the nut (F) Connecting part between the joint (B) and the end surface of the pump (H)
----------
V1=1.6V
----------




Have questions with 107492-2170?





Group cross 107492-2170 ZEXEL

9 400 612 403 
 
INJECTION-PUMP ASSEMBLY
9 400 612 404 
 
INJECTION-PUMP ASSEMBLY
4D34T3

Mitsubishi 

F 019 Z20 303 
ME015298 
INJECTION-PUMP ASSEMBLY
4D34T3
 
 
INJECTION-PUMP ASSEMBLY
 
 
INJECTION-PUMP ASSEMBLY
9 400 618 851 
 
INJECTION-PUMP ASSEMBLY
4D34T3

Mitsubishi 

F 019 Z20 304 
ME011888 
INJECTION-PUMP ASSEMBLY
4D34T3
 
 
INJECTION-PUMP ASSEMBLY
 
 
INJECTION-PUMP ASSEMBLY
9 400 618 852 
 
INJECTION-PUMP ASSEMBLY
4D34T3

Mitsubishi 

F 019 Z20 305 
ME011889 
INJECTION-PUMP ASSEMBLY
4D34T3
 
 
INJECTION-PUMP ASSEMBLY
 
 
INJECTION-PUMP ASSEMBLY
9 400 618 853 
 
INJECTION-PUMP ASSEMBLY
4D34T3

Mitsubishi 

F 019 Z20 306 
ME011890 
INJECTION-PUMP ASSEMBLY
4D34T3
 
 
INJECTION-PUMP ASSEMBLY
 
 
INJECTION-PUMP ASSEMBLY
9 400 618 854 
 
INJECTION-PUMP ASSEMBLY
4D34T3

Mitsubishi 

F 019 Z20 307 
ME011891 
INJECTION-PUMP ASSEMBLY
4D34T3
 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

9 400 618 855 
ME015138 
INJECTION-PUMP ASSEMBLY
4D34T3
 
 
INJECTION-PUMP ASSEMBLY
 
 
INJECTION-PUMP ASSEMBLY
9 400 618 856 
 
INJECTION-PUMP ASSEMBLY
4D34T3
9 400 619 611 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

9 400 619 945 
ME015066 
INJECTION-PUMP ASSEMBLY
4D34T3
107492-2170  

107492-2171 
9 400 618 857 
 
INJECTION-PUMP ASSEMBLY
4D34T3
 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

9 400 619 946 
ME215068 
INJECTION-PUMP ASSEMBLY
4D34T3
Back to top