106991-1912 ZEXEL 9 400 612 290 BOSCH INJECTION-PUMP ASSEMBLY 9400612290 1069911912 1156031922


106991-1912 INJECTION-PUMP ASSEMBLY
Rating:
21
Buy INJECTION-PUMP ASSEMBLY 106991-1912 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

BOSCH 9 400 612 290 9400612290
ZEXEL 106991-1912 1069911912
ISUZU 1156031922 1156031922

Service parts 106991-1912 INJECTION-PUMP ASSEMBLY:

1. _
2. FUEL INJECTION PUMP 106099-9670
3. GOVERNOR 105923-2900
4. SUPPLY PUMP 105237-5270
5. AUTOM. ADVANCE MECHANIS 105693-0530
6. COUPLING PLATE
7. COUPLING PLATE
8. _
9. _
10. NOZZLE AND HOLDER ASSY 105101-7750
11. Nozzle and Holder 1-15300-328-0
12. Open Pre:MPa(Kqf/cm2) 15.7{160}/22.1{225}
13. NOZZLE-HOLDER 105030-3540
14. NOZZLE 105025-0090
15. NOZZLE SET

Include in #1:

106991-1912 as INJECTION-PUMP ASSEMBLY

Cross reference number

BOSCH 9 400 612 290 9400612290
ZEXEL 106991-1912 1069911912
ISUZU 1156031922 1156031922


Zexel num
Bosch num
Firm num
Name
106991-1912 
9 400 612 290 
1156031922  ISUZU
INJECTION-PUMP ASSEMBLY
10PE1HRA K 14CE INJECTION PUMP ASSY PE10P PE

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil
  ISO4113 or {SAEJ967d}
Test oil temperature degC   40 40 45
Nozzle and nozzle holder   105780-8250
Bosch type code   1 688 901 101
Nozzle   105780-0120
Bosch type code   1 688 901 990
Nozzle holder   105780-2190
Opening pressure MPa   20.7
Opening pressure kgf/cm2   211
Injection pipe
Outer diameter - inner diameter - length (mm)
mm   8-3-600
Overflow valve   134424-4320
Overflow valve opening pressure kPa   255 221 289
Overflow valve opening pressure kgf/cm2   2.6 2.25 2.95
Tester oil delivery pressure kPa   255 255 255
Tester oil delivery pressure kgf/cm2   2.6 2.6 2.6
Direction of rotation (viewed from drive side)
Right
  R
Injection timing adjustment
Direction of rotation (viewed from drive side)
Right
  R
Injection order   1-8-7-6- 5-4-3-10 -9-2
Pre-stroke mm   5.5 5.47 5.53
Rack position
Point A
  R=A
Beginning of injection position
Governor side
  NO.1
Difference between angles 1
Cal 1-8
deg.   27 26.75 27.25
Difference between angles 2
Cal 1-7
deg.   72 71.75 72.25
Difference between angles 3
Cal 1-6
deg.   99 98.75 99.25
Difference between angles 4
Cal 1-5
deg.   144 143.75 144.25
Difference between angles 5
Cal 1-4
deg.   171 170.75 171.25
Difference between angles 6
Cal 1-3
deg.   216 215.75 216.25
Difference between angles 7
Cal 1-10
deg.   243 242.75 243.25
Difference between angles 8
Cal 1-9
deg.   288 287.75 288.25
Difference between angles 9
Cyl.1-2
deg.   315 314.75 315.25
Injection quantity adjustment
Adjusting point   -
Rack position   11.4
Pump speed r/min   700 700 700
Average injection quantity mm3/st.   148 146.4 149.6
Max. variation between cylinders %   0 -3 3
Basic   *
Fixing the rack   *
Standard for adjustment of the maximum variation between cylinders   *
Injection quantity adjustment_02
Adjusting point   Z
Rack position   6.6+-0.5
Pump speed r/min   405 405 405
Average injection quantity mm3/st.   13.5 11.5 15.5
Max. variation between cylinders %   0 -13 13
Fixing the rack   *
Standard for adjustment of the maximum variation between cylinders   *
Injection quantity adjustment_03
Adjusting point   A
Rack position   R1(11.4)
Pump speed r/min   700 700 700
Average injection quantity mm3/st.   148 147 149
Basic   *
Fixing the lever   *
Injection quantity adjustment_04
Adjusting point   B
Rack position   R1+0.95
Pump speed r/min   1150 1150 1150
Average injection quantity mm3/st.   142 138 146
Fixing the lever   *

Test data Ex:

Governor adjustment

Test data 106991-1912
N:Pump speed R:Rack position (mm) (1)Torque cam stamping: T1 (2)Tolerance for racks not indicated: +-0.05mm. (3)Damper spring setting
----------
T1=AD65
----------

Timer adjustment

Test data 106991-1912
(1)Adjusting range (2)Step response time (N): Speed of the pump (L): Load (theta) Advance angle (Srd1) Step response time 1 (Srd2) Step response time 2 1. Adjusting conditions for the variable timer (1)Adjust the clearance between the pickup and the protrusion to L.
----------
L=1-0.2mm N2=800r/min C2=(8)deg t1=1.5--sec. t2=1.5--sec.
----------
N1=950++r/min P1=0kPa(0kgf/cm2) P2=392kPa(4kgf/cm2) C1=8+-0.3deg R01=0/4load R02=4/4load

Speed control lever angle

Test data 106991-1912
F:Full speed I:Idle (1)Use the pin at R = aa (2)Stopper bolt set position 'H'
----------
aa=41mm
----------
a=25.5deg+-5deg b=(34deg)+-3deg

Stop lever angle

Test data 106991-1912
N:Pump normal S:Stop the pump. (1)Use the pin at R = aa (2)Set the stopper bolt so that speed = bb and rack position = cc. (Confirm non-injection.)
----------
aa=40mm bb=0r/min cc=1.5+-0.3mm
----------
a=20deg+-5deg b=43deg+-5deg

0000001501 RACK SENSOR

Test data 106991-1912
Rack sensor adjustment 1. Flange type rack sensor (rack sensor adjustment -5*20) (1)These types of rack sensors do not need adjustment. Confirm the performance with the following procedures. (2)Mount the rack sensor main body to the pump main body. (3)Fix the pump lever at full. (4)At supply voltage V1, pump speed N1 and rack position Ra, confirm that the amp's output voltage is Vist. (5)Move the pump lever two or three times. (6)Set again to full. (7)Confirm that the amplifier output voltage is Vist. (8)Fix the caution plate to the upper part of the rack sensor. (For those without the caution plate instructions, make sure the nameplate of the rack sensor carries the "Don't hold here" caution.) (9)Apply red paint to the rack sensor mounting bolts (2 places).
----------
V1=5+-0.01V N1=740r/min Ra=R1(11.4)+0.05mm Vist=1.66+-0.14V
----------

Timing setting

Test data 106991-1912
(1)Pump vertical direction (2)Position of "Z" mark at the No 1 cylinder's beginning of injection (governor side) (3)B.T.D.C.: aa (4)-
----------
aa=4deg
----------
a=(180deg)




Have questions with 106991-1912?





Group cross 106991-1912 ZEXEL

Isuzu 

 
1156031910 
INJECTION-PUMP ASSEMBLY
10PE1-N
 
1156031911 
INJECTION-PUMP ASSEMBLY
10PE1-N
9 400 618 798 
1156031912 
INJECTION-PUMP ASSEMBLY
10PE1-N
F 01G 09U 0CR 
1156031920 
INJECTION-PUMP ASSEMBLY
10PE1HRA
F 01G 09U 0CS 
1156031921 
INJECTION-PUMP ASSEMBLY
10PE1HRA
106991-1912  
9 400 612 290 
1156031922 
INJECTION-PUMP ASSEMBLY
10PE1HRA
F 01G 09U 0CT 
1156031930 
INJECTION-PUMP ASSEMBLY
10PE1NRA
9 400 611 725 
1156031931 
INJECTION-PUMP ASSEMBLY
10PE1NRA
9 400 618 799 
1156031932 
INJECTION-PUMP ASSEMBLY
10PE1NRA
 
1156031680 
INJECTION-PUMP ASSEMBLY
10PE1HRA
 
1156031681 
INJECTION-PUMP ASSEMBLY
10PE1HRA
9 400 618 800 
1156031682 
INJECTION-PUMP ASSEMBLY
10PE1HRA
 
1156031690 
INJECTION-PUMP ASSEMBLY
10PE1-N
 
1156031691 
INJECTION-PUMP ASSEMBLY
10PE1-N
9 400 618 801 
1156031692 
INJECTION-PUMP ASSEMBLY
10PE1-N
F 01G 09U 0CU 
1156031830 
INJECTION-PUMP ASSEMBLY
10PE1HRA
F 01G 09U 0CV 
1156031831 
INJECTION-PUMP ASSEMBLY
10PE1HRA
9 400 618 802 
1156031832 
INJECTION-PUMP ASSEMBLY
10PE1HRA
 
1156031840 
INJECTION-PUMP ASSEMBLY
10PE1NRA
 
1156031841 
INJECTION-PUMP ASSEMBLY
10PE1NRA
9 400 618 803 
1156031842 
INJECTION-PUMP ASSEMBLY
10PE1NRA
9 400 611 088 
1156032010 
INJECTION-PUMP ASSEMBLY
10PE1-S
9 400 612 552 
1156032011 
INJECTION-PUMP ASSEMBLY
10PE1-S
9 400 618 804 
1156032012 
INJECTION-PUMP ASSEMBLY
10PE1-S
9 400 611 089 
1156032020 
INJECTION-PUMP ASSEMBLY
10PE1-C
9 400 612 509 
1156032021 
INJECTION-PUMP ASSEMBLY
10PE1-C
9 400 618 805 
1156032022 
INJECTION-PUMP ASSEMBLY
10PE1-C
9 400 611 090 
1156032030 
INJECTION-PUMP ASSEMBLY
10PE1-S
9 400 612 791 
1156032031 
INJECTION-PUMP ASSEMBLY
10PE1-S
9 400 618 806 
1156032032 
INJECTION-PUMP ASSEMBLY
10PE1-S
Back to top