106991-1540 ZEXEL F 019 Z10 557 BOSCH INJECTION-PUMP ASSEMBLY f019z10557 1069911540


106991-1540 INJECTION-PUMP ASSEMBLY
Rating:
75
Buy INJECTION-PUMP ASSEMBLY 106991-1540 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

BOSCH F 019 Z10 557 f019z10557
ZEXEL 106991-1540 1069911540

Service parts 106991-1540 INJECTION-PUMP ASSEMBLY:

1. _
2. FUEL INJECTION PUMP 106099-9230
3. GOVERNOR 105489-4090
4. SUPPLY PUMP 105237-4420
5. AUTOM. ADVANCE MECHANIS 105693-0271
6. COUPLING PLATE
7. COUPLING PLATE
8. _
9. _
10. NOZZLE AND HOLDER ASSY 105100-7851
11. Nozzle and Holder
12. Open Pre:MPa(Kqf/cm2) 15.7{160}/22.1{225}
13. NOZZLE-HOLDER 105031-4831
14. NOZZLE 105015-8200
15. NOZZLE SET

Include in #1:

106991-1540 as INJECTION-PUMP ASSEMBLY

Cross reference number

BOSCH F 019 Z10 557 f019z10557
ZEXEL 106991-1540 1069911540


Zexel num
Bosch num
Firm num
Name
106991-1540 
106991-1541 
F 019 Z10 557 
   
INJECTION-PUMP ASSEMBLY
* K

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil
  ISO4113 or {SAEJ967d}
Test oil temperature degC   40 40 45
Nozzle and nozzle holder   105780-8140
Bosch type code   EF8511/9A
Nozzle   105780-0000
Bosch type code   DN12SD12T
Nozzle holder   105780-2080
Bosch type code   EF8511/9
Opening pressure MPa   17.2
Opening pressure kgf/cm2   175
Injection pipe
Outer diameter - inner diameter - length (mm)
mm   8-3-600
Overflow valve (drive side)   134424-4320
Overflow valve opening pressure (drive side) kPa   255 221 289
Overflow valve opening pressure (drive side) kgf/cm2   2.6 2.25 2.95
Overflow valve (governor side)   134424-4320
Overflow valve opening pressure (governor side) kPa   255 221 289
Overflow valve opening pressure (governor side) kgf/cm2   2.6 2.25 2.95
Tester oil delivery pressure kPa   157 157 157
Tester oil delivery pressure kgf/cm2   1.6 1.6 1.6
Direction of rotation (viewed from drive side)
Right
  R
Injection timing adjustment
Direction of rotation (viewed from drive side)
Right
  R
Injection order   1-4-9-8- 5-2-11-1 0-3-6-7-
Pre-stroke mm   4.2 4.17 4.23
Rack position
Point A
  R=A
Beginning of injection position
Governor side
  NO.1
Difference between angles 1
Cal 1-4
deg.   15 14.75 15.25
Difference between angles 2
Cal 1-9
deg.   60 59.75 60.25
Difference between angles 3
Cal 1-8
deg.   75 74.75 75.25
Difference between angles 4
Cal 1-5
deg.   120 119.75 120.25
Difference between angles 5
Cyl.1-2
deg.   135 134.75 135.25
Difference between angles 6
Cal 1-11
deg.   180 179.75 180.25
Difference between angles 7
Cal 1-10
deg.   195 194.75 195.25
Difference between angles 8
Cal 1-3
deg.   240 239.75 240.25
Difference between angles 9
Cal 1-6
deg.   255 254.75 255.25
Difference between angles 10
Cal 1-7
deg.   300 299.75 300.25
Difference between angles 11
Cal 1-12
deg.   315 314.75 315.25
Injection quantity adjustment
Adjusting point   A
Rack position   8.9
Pump speed r/min   800 800 800
Average injection quantity mm3/st.   112 110.5 113.5
Max. variation between cylinders %   0 -2 2
Basic   *
Fixing the lever   *
Injection quantity adjustment_02
Adjusting point   C
Rack position   8.15
Pump speed r/min   1150 1150 1150
Average injection quantity mm3/st.   116 114 118
Fixing the lever   *
Injection quantity adjustment_03
Adjusting point   D
Rack position   4.9+-0.5
Pump speed r/min   225 225 225
Average injection quantity mm3/st.   8.8 7.5 10.1
Max. variation between cylinders %   0 -13 13
Fixing the rack   *

Test data Ex:

Governor adjustment

Test data 106991-1540
N:Pump speed R:Rack position (mm) (1)Tolerance for racks not indicated: +-0.05mm. (2)Damper spring setting
----------

----------

Timer adjustment

Test data 106991-1540
(1)Adjusting range (2)Step response time (N): Speed of the pump (L): Load (theta) Advance angle (Srd1) Step response time 1 (Srd2) Step response time 2 1. Adjusting conditions for the variable timer (1)Adjust the clearance between the pickup and the protrusion to L.
----------
L=1-0.2mm N2=800r/min C2=(7)deg t1=1.5--sec. t2=1.5--sec.
----------
N1=1100++r/min P1=0kPa(0kgf/cm2) P2=392kPa(4kgf/cm2) C1=7+-0.3deg R01=0/4load R02=4/4load

Speed control lever angle

Test data 106991-1540
F:Full speed
----------

----------
a=6.5deg+-5deg

0000000901

Test data 106991-1540
F:Full load I:Idle (1)Stopper bolt setting
----------

----------
a=10deg+-5deg b=33deg+-3deg

Stop lever angle

Test data 106991-1540
N:Pump normal S:Stop the pump. (1)Use the hole at R = aa
----------
aa=25mm
----------
a=51deg+-5deg b=64deg+-5deg

0000001501 RACK SENSOR

Rack sensor adjustment (1)These types of rack sensors do not need adjustment. Confirm the output as described below. (2)Mount the rack sensor main body to the pump main body. (3)Measure the Vist at pump speed N1 and rack position Ra.
----------
N1=500r/min Ra=8.75mm
----------

Timing setting

Test data 106991-1540
(1)Pump vertical direction (2)Position of "Z" mark at the No 1 cylinder's beginning of injection (governor side) (3)B.T.D.C.: aa (set timing) (4)-
----------
aa=8deg
----------
a=(180deg)




Have questions with 106991-1540?





Group cross 106991-1540 ZEXEL

Isuzu 

 
1156028360 
INJECTION-PUMP ASSEMBLY
12PD1-C
 
1156028361 
INJECTION-PUMP ASSEMBLY
12PD1-C
 
 
INJECTION-PUMP ASSEMBLY

Isuzu 

 
1156028363 
INJECTION-PUMP ASSEMBLY
12PD1-C
 
1156030130 
INJECTION-PUMP ASSEMBLY
12PD1-C
9 400 618 770 
1156030131 
INJECTION-PUMP ASSEMBLY
12PD1-C
 
1156028370 
INJECTION-PUMP ASSEMBLY
12PD1-C
 
1156028371 
INJECTION-PUMP ASSEMBLY
12PD1-C
 
 
INJECTION-PUMP ASSEMBLY

Isuzu 

 
1156028373 
INJECTION-PUMP ASSEMBLY
12PD1-C
 
1156030140 
INJECTION-PUMP ASSEMBLY
12PD1-C
 
1156030141 
INJECTION-PUMP ASSEMBLY
12PD1-C
 
1156030142 
INJECTION-PUMP ASSEMBLY
12PD1-C
9 400 618 771 
1156030143 
INJECTION-PUMP ASSEMBLY
12PD1-C
 
1156028400 
INJECTION-PUMP ASSEMBLY
12PD1-S
 
1156028401 
INJECTION-PUMP ASSEMBLY
12PD1-S
 
 
INJECTION-PUMP ASSEMBLY

Isuzu 

 
1156028403 
INJECTION-PUMP ASSEMBLY
12PD1-S
 
1156030170 
INJECTION-PUMP ASSEMBLY
12PD1-S
9 400 618 772 
1156030171 
INJECTION-PUMP ASSEMBLY
12PD1-S
 
1156028410 
INJECTION-PUMP ASSEMBLY
12PD1-C
 
1156028411 
INJECTION-PUMP ASSEMBLY
12PD1-C
 
 
INJECTION-PUMP ASSEMBLY

Isuzu 

 
1156028413 
INJECTION-PUMP ASSEMBLY
12PD1-C
 
1156030180 
INJECTION-PUMP ASSEMBLY
12PD1-C
9 400 618 773 
1156030181 
INJECTION-PUMP ASSEMBLY
12PD1-C
106991-1540  

106991-1541 
F 019 Z10 557 
 
INJECTION-PUMP ASSEMBLY

Isuzu 

9 400 618 774 
1156028650 
INJECTION-PUMP ASSEMBLY
12PD1-S
9 400 611 072 
1156029071 
INJECTION-PUMP ASSEMBLY
10PD1
9 400 618 775 
1156029072 
INJECTION-PUMP ASSEMBLY
10PD1
 
1156029930 
INJECTION-PUMP ASSEMBLY
10PD1
9 400 618 776 
1156029931 
INJECTION-PUMP ASSEMBLY
10PD1
9 400 611 073 
1156028690 
INJECTION-PUMP ASSEMBLY
12PE1-N
9 400 611 074 
1156028800 
INJECTION-PUMP ASSEMBLY
10PE1-N
9 400 611 075 
1156029350 
INJECTION-PUMP ASSEMBLY
10PE1-N
Back to top