106971-1230 ZEXEL 9 400 611 290 BOSCH INJECTION-PUMP ASSEMBLY 9400611290 1069711230 1156033700

Information Cross number Calibration Data Calibration Data Ex

Price: query
Buy now
Add to cart Go to cart

Rating:

Buy INJECTION-PUMP ASSEMBLY 106971-1230 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

BOSCH 9 400 611 290 9400611290

ZEXEL 106971-1230 1069711230

ISUZU 1156033700 1156033700

Service parts 106971-1230 INJECTION-PUMP ASSEMBLY:

1. _

2. FUEL INJECTION PUMP 106091-9140

3. GOVERNOR 105923-4730

4. SUPPLY PUMP 105237-5280

5. AUTOM. ADVANCE MECHANIS 105687-0570

6. COUPLING PLATE

7. COUPLING PLATE

8. _

9. _

10. NOZZLE AND HOLDER ASSY 105101-7750

11. Nozzle and Holder 1-15300-328-0

12. Open Pre:MPa(Kqf/cm2) 15.7{160}/22.1{225}

13. NOZZLE-HOLDER 105030-3540

14. NOZZLE 105025-0090

15. NOZZLE SET

Include in #1:

106971-1230 as INJECTION-PUMP ASSEMBLY

Cross reference number

BOSCH 9 400 611 290 9400611290

ZEXEL 106971-1230 1069711230

ISUZU 1156033700 1156033700

Zexel num

Bosch num

Firm num

Name

106971-1230
106971-1231

9 400 611 290

1156033700 ISUZU

INJECTION-PUMP ASSEMBLY
10PE1 * K

Calibration Data:

Adjustment conditions

Test oil
1404 Test oil ISO4113 or {SAEJ967d}

Test oil temperature degC 40 40 45

Nozzle and nozzle holder 105780-8250

Bosch type code 1 688 901 101

Nozzle 105780-0120

Bosch type code 1 688 901 990

Nozzle holder 105780-2190

Opening pressure MPa 20.7

Opening pressure kgf/cm2 211

Injection pipe
Outer diameter - inner diameter - length (mm) mm 8-3-600

Overflow valve 134424-4320

Overflow valve opening pressure kPa 255 221 289

Overflow valve opening pressure kgf/cm2 2.6 2.25 2.95

Tester oil delivery pressure kPa 255 255 255

Tester oil delivery pressure kgf/cm2 2.6 2.6 2.6

Direction of rotation (viewed from drive side)
Right R

Injection timing adjustment

Direction of rotation (viewed from drive side)
Right R

Injection order 1-8-7-6- 5-4-3-10 -9-2

Pre-stroke mm 5.5 5.47 5.53

Rack position
Point A R=A

Beginning of injection position
Governor side NO.1

Difference between angles 1
Cal 1-8 deg. 27 26.75 27.25

Difference between angles 2
Cal 1-7 deg. 72 71.75 72.25

Difference between angles 3
Cal 1-6 deg. 99 98.75 99.25

Difference between angles 4
Cal 1-5 deg. 144 143.75 144.25

Difference between angles 5
Cal 1-4 deg. 171 170.75 171.25

Difference between angles 6
Cal 1-3 deg. 216 215.75 216.25

Difference between angles 7
Cal 1-10 deg. 243 242.75 243.25

Difference between angles 8
Cal 1-9 deg. 288 287.75 288.25

Difference between angles 9
Cyl.1-2 deg. 315 314.75 315.25

Injection quantity adjustment

Adjusting point -

Rack position 11.1

Pump speed r/min 800 800 800

Average injection quantity mm3/st. 122 120.4 123.6

Max. variation between cylinders % 0 -3 3

Basic *

Fixing the rack *

Standard for adjustment of the maximum variation between cylinders *

Injection quantity adjustment_02

Adjusting point Z

Rack position 6.7+-0.5

Pump speed r/min 420 420 420

Average injection quantity mm3/st. 13.5 11.5 15.5

Max. variation between cylinders % 0 -13 13

Fixing the rack *

Standard for adjustment of the maximum variation between cylinders *

Injection quantity adjustment_03

Adjusting point A

Rack position R1(11.1)

Pump speed r/min 800 800 800

Average injection quantity mm3/st. 122 121 123

Basic *

Fixing the lever *

Injection quantity adjustment_04

Adjusting point B

Rack position R1+1.5

Pump speed r/min 1150 1150 1150

Average injection quantity mm3/st. 133 129 137

Fixing the lever *

Timer adjustment

Pump speed r/min 500--

Advance angle deg. 0 0 0

Remarks
Start

Timer adjustment_02

Pump speed r/min 450

Advance angle deg. 0.3

Timer adjustment_03

Pump speed r/min 700

Advance angle deg. 2 1.5 2.5

Remarks
Finish

Test data Ex:

Governor adjustment

N:Pump speed R:Rack position (mm) (1)Torque cam stamping: T1 (2)Tolerance for racks not indicated: +-0.05mm. (3)Damper spring setting
----------
T1=AD98
----------

Speed control lever angle

F:Full speed I:Idle (1)Use the pin at R = aa (2)Stopper bolt set position 'H'
----------
aa=42.5mm
----------
a=22.5deg+-5deg b=30deg+-3deg

Stop lever angle

N:Pump normal S:Stop the pump. (1)Use the pin at R = aa (2)Set the stopper bolt so that speed = bb and rack position = cc. (Confirm non-injection.)
----------
aa=40mm bb=0r/min cc=1.5+-0.3mm
----------
a=20deg+-5deg b=43deg+-5deg

0000001501 ACS

(A) Set screw (B) Push rod 1 (C) Push rod 2 (D) Lever 1. Aneroid compensator unit adjustment (1)Screw in (A) to obtain L1. (2)Select C so that dimension L2 can be obtained. 2. Adjustment when mounting the governor. (1)Set the speed of the pump to N1 r/min and fix the control lever at the full set position. (2)Set to full boost. (3)Screw in the aneroid compensator body to obtain the performance shown in the graph above. (4)As there is hysterisis, measure when the absolute pressure drops. (5)Hysterisis must not exceed rack position = h1.
----------
N1=1150r/min L1=1.5+-0.5mm L2=36+-0.5mm h1=0.15mm
----------
Ra=R3(R1+1.5)mm Rb=- Rc=R3-0.8mm P1=(89.8)+-2.7kPa((674)+-20mmHg) P2=- P3=65.2+-0.7kPa(489+-5mmHg) Q1=(133)+-2cm3/1000st Q2=- Q3=(119)cm3/1000st

0000001601 TAMPER PROOF

(A): Rotation tamper proof (B): Full-speed setting 1. Back off the full-speed set bolt. 2. Confirm that the tamper setting position is N1, R1, Q1. 3. At that time, record the angle of the speed lever. 4. After confirming the above setting, set full speed.
----------
N1=(1490)r/min R1=6.8+-0.1mm Q1=-
----------

Timing setting

(1)Pump vertical direction (2)Position of "Z" mark at the No 1 cylinder's beginning of injection (governor side) (3)B.T.D.C.: aa (4)-
----------
aa=10deg
----------
a=(170deg)