106891-1551 ZEXEL 9 400 619 918 BOSCH INJECTION-PUMP ASSEMBLY 9400619918 1068911551 1156032051

Information Cross number Calibration Data Calibration Data Ex

Price: query
Buy now
Add to cart Go to cart

Rating:

Buy INJECTION-PUMP ASSEMBLY 106891-1551 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

BOSCH 9 400 619 918 9400619918

ZEXEL 106891-1551 1068911551

ISUZU 1156032051 1156032051

Service parts 106891-1551 INJECTION-PUMP ASSEMBLY:

1. _

2. FUEL INJECTION PUMP 106089-9250

3. GOVERNOR 105488-2181

4. SUPPLY PUMP 105237-5150

5. AUTOM. ADVANCE MECHANIS 105687-0740

6. COUPLING PLATE

7. COUPLING PLATE

8. _

9. _

10. NOZZLE AND HOLDER ASSY 105100-7851

11. Nozzle and Holder

12. Open Pre:MPa(Kqf/cm2) 15.7{160}/22.1{225}

13. NOZZLE-HOLDER 105031-4831

14. NOZZLE

105015-8200

15. NOZZLE SET

Include in #1:

106891-1551 as INJECTION-PUMP ASSEMBLY

Cross reference number

BOSCH 9 400 619 918 9400619918

ZEXEL 106891-1551 1068911551

ISUZU 1156032051 1156032051

Zexel num

Bosch num

Firm num

Name

106891-1551
106891-1552

9 400 619 918

1156032051 ISUZU

INJECTION-PUMP ASSEMBLY
8PE1 * K 14CD PE8P PE

Calibration Data:

Adjustment conditions

Test oil
1404 Test oil ISO4113 or {SAEJ967d}

Test oil temperature degC 40 40 45

Nozzle and nozzle holder 105780-8140

Bosch type code EF8511/9A

Nozzle 105780-0000

Bosch type code DN12SD12T

Nozzle holder 105780-2080

Bosch type code EF8511/9

Opening pressure MPa 17.2

Opening pressure kgf/cm2 175

Injection pipe
Outer diameter - inner diameter - length (mm) mm 8-3-600

Overflow valve 134424-4320

Overflow valve opening pressure kPa 255 221 289

Overflow valve opening pressure kgf/cm2 2.6 2.25 2.95

Tester oil delivery pressure kPa 157 157 157

Tester oil delivery pressure kgf/cm2 1.6 1.6 1.6

Direction of rotation (viewed from drive side)
Right R

Injection timing adjustment

Direction of rotation (viewed from drive side)
Right R

Injection order 1-8-7-3- 6-5-4-2

Pre-stroke mm 4.2 4.17 4.23

Rack position
Point A R=A

Beginning of injection position
Governor side NO.1

Difference between angles 1
Cal 1-8 deg. 45 44.75 45.25

Difference between angles 2
Cal 1-7 deg. 90 89.75 90.25

Difference between angles 3
Cal 1-3 deg. 135 134.75 135.25

Difference between angles 4
Cal 1-6 deg. 180 179.75 180.25

Difference between angles 5
Cal 1-5 deg. 225 224.75 225.25

Difference between angles 6
Cal 1-4 deg. 270 269.75 270.25

Difference between angles 7
Cyl.1-2 deg. 315 314.75 315.25

Injection quantity adjustment

Adjusting point A

Rack position 7.8

Pump speed r/min 800 800 800

Average injection quantity mm3/st. 101 99.5 102.5

Max. variation between cylinders % 0 -2 2

Basic *

Fixing the lever *

Injection quantity adjustment_02

Adjusting point C

Rack position 8.8

Pump speed r/min 350 350 350

Average injection quantity mm3/st. 100 96 104

Fixing the lever *

Injection quantity adjustment_03

Adjusting point D

Rack position 4.7+-0.5

Pump speed r/min 265 265 265

Average injection quantity mm3/st. 10 8.7 11.3

Max. variation between cylinders % 0 -13 13

Basic *

Fixing the rack *

Timer adjustment

Pump speed r/min 800--

Advance angle deg. 0 0 0

Remarks
Start

Timer adjustment_02

Pump speed r/min 750

Advance angle deg. 0.3

Timer adjustment_03

Pump speed r/min 1100

Advance angle deg. 3.5 3 4

Remarks
Finish

Test data Ex:

Governor adjustment

N:Pump speed R:Rack position (mm) (1)Lever ratio: RT (2)Target shim dimension: TH (3)Tolerance for racks not indicated: +-0.05mm. (4)Damper spring setting: DL
----------
RT=0.8 TH=1.7mm DL=3.7-0.2mm
----------

Speed control lever angle

F:Full speed
----------

----------
a=7deg+-5deg

0000000901

F:Full load I:Idle (1)Stopper bolt setting
----------

----------
a=10deg+-5deg b=29.5deg+-3deg

Stop lever angle

N:Pump normal S:Stop the pump. (1)Use the pin at R = aa (2)Drive side
----------
aa=23.5mm
----------
a=73deg+-5deg b=40deg+-5deg

0000001501 ACS

(A) Set screw 1. Aneroid compensator unit adjustment Screw in (A) to obtain L1. 2. Adjustment following governor installation (1)Set the speed of the pump to N1 r/min and fix the control lever at the full set position. (2)Screw in the aneroid compensator to obtain the performance shown in the graph above.
----------
N1=1150r/min L1=(0.1~0.5)mm
----------
R1=7.8mm R2=7.1mm P1=(89.8)kPa((674)mmHg) P2=69.8+-0.7kPa(524+-5mmHg) Q1=120.5+-4cm3/1000st Q2=104+-10cm3/1000st

Timing setting

(1)Pump vertical direction (2)Position of "Z" mark at the No 1 cylinder's beginning of injection (governor side) (3)B.T.D.C.: aa (4)-
----------
aa=12deg
----------
a=(170deg)