106873-7721 ZEXEL INJECTION-PUMP ASSEMBLY Calibration Data 1068737721


106873-7721 INJECTION-PUMP ASSEMBLY
Rating:
14
Buy INJECTION-PUMP ASSEMBLY 106873-7721 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

ZEXEL 106873-7721 1068737721

Service parts 106873-7721 INJECTION-PUMP ASSEMBLY:

1. _
2. FUEL INJECTION PUMP 106080-7091
3. GOVERNOR 105923-2991
4. SUPPLY PUMP 105237-5020
5. AUTOM. ADVANCE MECHANIS 105691-4040
6. COUPLING PLATE 105664-2020
7. COUPLING PLATE
8. _
9. _
10. NOZZLE AND HOLDER ASSY 105110-7391
11. Nozzle and Holder ME161933
12. Open Pre:MPa(Kqf/cm2) 15.7{160}/24.5{250}
13. NOZZLE-HOLDER 105041-4101
14. NOZZLE
15. NOZZLE SET 105019-0380

Include in #1:

106873-7721 as INJECTION-PUMP ASSEMBLY

Cross reference number

ZEXEL 106873-7721 1068737721


Zexel num
Bosch num
Firm num
Name
106873-7721 
 
   
INJECTION-PUMP ASSEMBLY

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil
  ISO4113 or {SAEJ967d}
Test oil temperature degC   40 40 45
Nozzle and nozzle holder   105780-8250
Bosch type code   1 688 901 101
Nozzle   105780-0120
Bosch type code   1 688 901 990
Nozzle holder   105780-2190
Opening pressure MPa   20.7
Opening pressure kgf/cm2   211
Injection pipe
Outer diameter - inner diameter - length (mm)
mm   8-3-600
Overflow valve   131425-0220
Overflow valve opening pressure kPa   157 123 191
Overflow valve opening pressure kgf/cm2   1.6 1.25 1.95
Tester oil delivery pressure kPa   255 255 255
Tester oil delivery pressure kgf/cm2   2.6 2.6 2.6
Direction of rotation (viewed from drive side)
Right
  R
Injection timing adjustment
Direction of rotation (viewed from drive side)
Right
  R
Injection order   1-2-7-3- 4-5-6-8
Pre-stroke mm   3.9 3.85 3.95
Beginning of injection position
Governor side
  NO.1
Difference between angles 1
Cyl.1-2
deg.   45 44.5 45.5
Difference between angles 2
Cal 1-7
deg.   90 89.5 90.5
Difference between angles 3
Cal 1-3
deg.   135 134.5 135.5
Difference between angles 4
Cal 1-4
deg.   180 179.5 180.5
Difference between angles 5
Cal 1-5
deg.   225 224.5 225.5
Difference between angles 6
Cal 1-6
deg.   270 269.5 270.5
Difference between angles 7
Cal 1-8
deg.   315 314.5 315.5
Injection quantity adjustment
Adjusting point   -
Rack position   12.7
Pump speed r/min   700 700 700
Each cylinder's injection qty mm3/st.   144 139.7 148.3
Basic   *
Fixing the rack   *
Standard for adjustment of the maximum variation between cylinders   *
Injection quantity adjustment_02
Adjusting point   Z
Rack position   8+-0.5
Pump speed r/min   445 445 445
Each cylinder's injection qty mm3/st.   16.5 14 19
Fixing the rack   *
Standard for adjustment of the maximum variation between cylinders   *
Injection quantity adjustment_03
Adjusting point   A
Rack position   R1(12.7)
Pump speed r/min   700 700 700
Average injection quantity mm3/st.   144 143 145
Basic   *
Fixing the lever   *
Injection quantity adjustment_04
Adjusting point   B
Rack position   R1+0.8
Pump speed r/min   1100 1100 1100
Average injection quantity mm3/st.   139 135 143
Fixing the lever   *
Injection quantity adjustment_05
Adjusting point   C
Rack position   (R1-0.8)
Pump speed r/min   500 500 500
Average injection quantity mm3/st.   139.5 135.5 143.5
Fixing the lever   *

Test data Ex:

Governor adjustment

Test data 106873-7721
N:Pump speed R:Rack position (mm) (1)Torque cam stamping: T1 (2)Tolerance for racks not indicated: +-0.05mm. (3)Damper spring setting
----------
T1=AD95
----------

Timer adjustment

Test data 106873-7721
(1)Adjusting range (2)Step response time (N): Speed of the pump (L): Load (theta) Advance angle (Srd1) Step response time 1 (Srd2) Step response time 2 1. Adjusting conditions for the variable timer (1)Adjust the clearance between the pickup and the protrusion to L.
----------
L=1-0.2mm N2=800r/min C2=(10deg) t1=2.5--sec. t2=2.5--sec.
----------
N1=750++r/min P1=0kPa(0kgf/cm2) P2=392kPa(4kgf/cm2) C1=10+-0.3deg R01=0/4load R02=4/4load

Speed control lever angle

Test data 106873-7721
F:Full speed I:Idle (1)Use the hole at R = aa (2)Stopper bolt set position 'H' (3)Viewed from feed pump side.
----------
aa=37.5mm
----------
a=30deg+-5deg b=(37deg)+-3deg

Stop lever angle

Test data 106873-7721
N:Pump normal S:Stop the pump. (1)Use the hole at R = aa (2)Set the stopper bolt so that speed = bb and rack position = cc. (Confirm non-injection.) (3)Normal engine position (Rack position corresponding to dd)
----------
aa=54mm bb=1100r/min cc=3.5+-0.3mm dd=18mm
----------
a=41deg+-5deg b=5.5deg+-5deg c=(31deg)

0000001501 RACK SENSOR

Test data 106873-7721
(VR) measurement voltage (I) Part number of the control unit (G) Apply red paint. (H): End surface of the pump 1. Rack sensor adjustment (-0620) (1)Fix the speed control lever at the full position (2)Set the speed to N1 r/min. (If the boost compensator is provided, apply boost pressure.) (3)Adjust the bobbin (A) so that the rack sensor's output voltage is VR+-0.01. (4)At that time, rack position must be Ra. (5)Apply G at two places. Connecting part between the joint (B) and the nut (F) Connecting part between the joint (B) and the end surface of the pump (H)
----------
N1=1100r/min Ra=R1(12.7)+0.8mm
----------

Timing setting

Test data 106873-7721
(1)Pump vertical direction (2)Coupling's key groove position at No 1 cylinder's beginning of injection (3)B.T.D.C.: aa (4)-
----------
aa=6deg
----------
a=(50deg)




Have questions with 106873-7721?





Group cross 106873-7721 ZEXEL

Mitsubishi 

9 400 611 047 
ME094940 
INJECTION-PUMP ASSEMBLY
8DC9
 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

9 400 618 510 
ME094943 
INJECTION-PUMP ASSEMBLY
8DC9T2
 
 
INJECTION-PUMP ASSEMBLY
106873-7721  
 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

9 400 618 511 
ME163507 
INJECTION-PUMP ASSEMBLY
8M20
9 400 611 048 
ME094931 
INJECTION-PUMP ASSEMBLY
8DC9
 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

9 400 618 512 
ME094941 
INJECTION-PUMP ASSEMBLY
8DC9
 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

9 400 618 513 
ME094942 
INJECTION-PUMP ASSEMBLY
8DC9
F 01G 09U 0BH 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

9 400 618 514 
ME094944 
INJECTION-PUMP ASSEMBLY
8DC9T2
 
 
INJECTION-PUMP ASSEMBLY
 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

9 400 611 799 
ME163508 
INJECTION-PUMP ASSEMBLY
8M20
9 400 611 474 
ME094929 
INJECTION-PUMP ASSEMBLY
8DC91
 
ME359469 
INJECTION-PUMP ASSEMBLY
8DC91TC
9 400 618 515 
ME094930 
INJECTION-PUMP ASSEMBLY
8DC91
Back to top