106873-7320 ZEXEL 9 400 611 038 BOSCH INJECTION-PUMP ASSEMBLY 9400611038 1068737320 me162638


106873-7320 INJECTION-PUMP ASSEMBLY
Rating:
34
Buy INJECTION-PUMP ASSEMBLY 106873-7320 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

BOSCH 9 400 611 038 9400611038
ZEXEL 106873-7320 1068737320
MITSUBISHI ME162638 me162638

Service parts 106873-7320 INJECTION-PUMP ASSEMBLY:

1. _
2. FUEL INJECTION PUMP 106080-5790
3. GOVERNOR 105923-1710
4. SUPPLY PUMP 105237-4770
5. AUTOM. ADVANCE MECHANIS 105691-3930
6. COUPLING PLATE 105664-2020
7. COUPLING PLATE
8. _
9. _
10. NOZZLE AND HOLDER ASSY 105110-7391
11. Nozzle and Holder ME161933
12. Open Pre:MPa(Kqf/cm2) 15.7{160}/24.5{250}
13. NOZZLE-HOLDER 105041-4101
14. NOZZLE
15. NOZZLE SET 105019-0380

Include in #1:

106873-7320 as INJECTION-PUMP ASSEMBLY

Cross reference number

BOSCH 9 400 611 038 9400611038
ZEXEL 106873-7320 1068737320
MITSUBISHI ME162638 me162638


Zexel num
Bosch num
Firm num
Name
106873-7320 
106873-7450 
9 400 611 038 
ME162638  MITSUBISHI
INJECTION-PUMP ASSEMBLY
8M20 K

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil
  ISO4113 or {SAEJ967d}
Test oil temperature degC   40 40 45
Nozzle and nozzle holder   105780-8250
Bosch type code   1 688 901 101
Nozzle   105780-0120
Bosch type code   1 688 901 990
Nozzle holder   105780-2190
Opening pressure MPa   20.7
Opening pressure kgf/cm2   211
Injection pipe
Outer diameter - inner diameter - length (mm)
mm   8-3-600
Overflow valve   131425-0220
Overflow valve opening pressure kPa   157 123 191
Overflow valve opening pressure kgf/cm2   1.6 1.25 1.95
Tester oil delivery pressure kPa   255 255 255
Tester oil delivery pressure kgf/cm2   2.6 2.6 2.6
Direction of rotation (viewed from drive side)
Right
  R
Injection timing adjustment
Direction of rotation (viewed from drive side)
Right
  R
Injection order   1-2-7-3- 4-5-6-8
Pre-stroke mm   3.9 3.85 3.95
Beginning of injection position
Governor side
  NO.1
Difference between angles 1
Cyl.1-2
deg.   45 44.5 45.5
Difference between angles 2
Cal 1-7
deg.   90 89.5 90.5
Difference between angles 3
Cal 1-3
deg.   135 134.5 135.5
Difference between angles 4
Cal 1-4
deg.   180 179.5 180.5
Difference between angles 5
Cal 1-5
deg.   225 224.5 225.5
Difference between angles 6
Cal 1-6
deg.   270 269.5 270.5
Difference between angles 7
Cal 1-8
deg.   315 314.5 315.5
Injection quantity adjustment
Adjusting point   -
Rack position   12.6
Pump speed r/min   700 700 700
Each cylinder's injection qty mm3/st.   142 137.7 146.3
Basic   *
Fixing the rack   *
Standard for adjustment of the maximum variation between cylinders   *
Injection quantity adjustment_02
Adjusting point   Z
Rack position   8+-0.5
Pump speed r/min   445 445 445
Each cylinder's injection qty mm3/st.   16.5 14 19
Fixing the rack   *
Standard for adjustment of the maximum variation between cylinders   *
Injection quantity adjustment_03
Adjusting point   A
Rack position   R1(12.6)
Pump speed r/min   700 700 700
Average injection quantity mm3/st.   142 141 143
Basic   *
Fixing the lever   *
Injection quantity adjustment_04
Adjusting point   B
Rack position   R1+1.05
Pump speed r/min   1100 1100 1100
Average injection quantity mm3/st.   140 136 144
Fixing the lever   *
Injection quantity adjustment_05
Adjusting point   C
Rack position   (R1-0.8)
Pump speed r/min   500 500 500
Average injection quantity mm3/st.   138 134 142
Fixing the lever   *

Test data Ex:

Governor adjustment

Test data 106873-7320
N:Pump speed R:Rack position (mm) (1)Torque cam stamping: T1 (2)Tolerance for racks not indicated: +-0.05mm. (3)Damper spring setting
----------
T1=AC95
----------

Timer adjustment

Test data 106873-7320
(1)Adjusting range (2)Step response time (N): Speed of the pump (L): Load (theta) Advance angle (Srd1) Step response time 1 (Srd2) Step response time 2 1. Adjusting conditions for the variable timer (1)Adjust the clearance between the pickup and the protrusion to L.
----------
L=1-0.2mm N2=800r/min C2=(10)deg t1=2.5--sec. t2=2.5--sec.
----------
N1=750++r/min P1=0kPa(0kgf/cm2) P2=392kPa(4kgf/cm2) C1=10+-0.3deg R01=0/4load R02=4/4load

Speed control lever angle

Test data 106873-7320
F:Full speed I:Idle (1)Use the hole at R = aa (2)Stopper bolt set position 'H' (3)Viewed from feed pump side.
----------
aa=37.5mm
----------
a=30deg+-5deg b=35deg+-3deg

Stop lever angle

Test data 106873-7320
N:Pump normal S:Stop the pump. (1)Use the hole at R = aa (2)Set the stopper bolt so that speed = bb and rack position = cc. (Confirm non-injection.) (3)Normal engine position (Rack position corresponding to dd)
----------
aa=54mm bb=1100r/min cc=3.5+-0.3mm dd=18mm
----------
a=41deg+-5deg b=5.5deg+-5deg c=(31deg)

0000001501 RACK SENSOR

Test data 106873-7320
(VR) measurement voltage (I) Part number of the control unit (G) Apply red paint. (H): End surface of the pump 1. Rack sensor adjustment (-0620) (1)Fix the speed control lever at the full position (2)Set the speed to N1 r/min. (If the boost compensator is provided, apply boost pressure.) (3)Adjust the bobbin (A) so that the rack sensor's output voltage is VR+-0.01. (4)At that time, rack position must be Ra. (5)Apply G at two places. Connecting part between the joint (B) and the nut (F) Connecting part between the joint (B) and the end surface of the pump (H)
----------
N1=1100r/min Ra=R1(12.6)+1.05mm
----------

Timing setting

Test data 106873-7320
(1)Pump vertical direction (2)Coupling's key groove position at No 1 cylinder's beginning of injection (3)B.T.D.C.: aa (4)-
----------
aa=6deg
----------
a=(50deg)




Have questions with 106873-7320?





Group cross 106873-7320 ZEXEL

Mitsubishi 

9 400 611 037 
ME094239 
INJECTION-PUMP ASSEMBLY
8DC9
 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

9 400 618 482 
ME094240 
INJECTION-PUMP ASSEMBLY
8DC9
106873-7320  

106873-7450 
9 400 611 038 
ME162638 
INJECTION-PUMP ASSEMBLY
8M20
9 400 618 483 
ME162639 
INJECTION-PUMP ASSEMBLY
8M20
 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

9 400 618 484 
ME094377 
INJECTION-PUMP ASSEMBLY
8DC9
F 019 Z10 210 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

9 400 618 485 
ME094288 
INJECTION-PUMP ASSEMBLY
8DC9
9 400 619 422 
ME354502 
INJECTION-PUMP ASSEMBLY
8DC9
9 400 619 465 
 
INJECTION-PUMP ASSEMBLY
9 400 619 466 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

9 400 618 486 
ME094376 
INJECTION-PUMP ASSEMBLY
8DC9T2
9 400 618 487 
ME162789 
INJECTION-PUMP ASSEMBLY
8M20
 
 
INJECTION-PUMP ASSEMBLY
 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

9 400 618 488 
ME094420 
INJECTION-PUMP ASSEMBLY
8DC9T2
9 400 611 039 
ME098734 
INJECTION-PUMP ASSEMBLY
8DC9T2
F 019 Z10 233 
ME443024 
INJECTION-PUMP ASSEMBLY
8DC9T2
Back to top