106873-3522 ZEXEL 9 400 618 440 BOSCH INJECTION-PUMP ASSEMBLY 9400618440 1068733522 220801771a


106873-3522 INJECTION-PUMP ASSEMBLY
Rating:
8
Buy INJECTION-PUMP ASSEMBLY 106873-3522 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

BOSCH 9 400 618 440 9400618440
ZEXEL 106873-3522 1068733522
HINO 220801771A 220801771a

Cross reference number

BOSCH 9 400 618 440 9400618440
ZEXEL 106873-3522 1068733522
HINO 220801771A 220801771a


Zexel num
Bosch num
Firm num
Name
106873-3522 
9 400 618 440 
220801771A  HINO
INJECTION-PUMP ASSEMBLY
F-2 * K 14CD PE8P PE

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil
  ISO4113 or {SAEJ967d}
Test oil temperature degC   40 40 45
Nozzle and nozzle holder   105780-8140
Bosch type code   EF8511/9A
Nozzle   105780-0000
Bosch type code   DN12SD12T
Nozzle holder   105780-2080
Bosch type code   EF8511/9
Opening pressure MPa   17.2
Opening pressure kgf/cm2   175
Injection pipe
Outer diameter - inner diameter - length (mm)
mm   8-3-600
Overflow valve   131425-0020
Overflow valve opening pressure kPa   127 127 127
Overflow valve opening pressure kgf/cm2   1.3 1.3 1.3
Tester oil delivery pressure kPa   157 157 157
Tester oil delivery pressure kgf/cm2   1.6 1.6 1.6
Direction of rotation (viewed from drive side)
Right
  R
Injection timing adjustment
Direction of rotation (viewed from drive side)
Right
  R
Injection order   1-8-6-2- 7-5-4-3
Pre-stroke mm   4.2 4.14 4.2
Beginning of injection position
Drive side
  NO.1
Difference between angles 1
Cal 1-8
deg.   45 44.75 45.25
Difference between angles 2
Cal 1-6
deg.   90 89.75 90.25
Difference between angles 3
Cyl.1-2
deg.   135 134.75 135.25
Difference between angles 4
Cal 1-7
deg.   180 179.75 180.25
Difference between angles 5
Cal 1-5
deg.   225 224.75 225.25
Difference between angles 6
Cal 1-4
deg.   270 269.75 270.25
Difference between angles 7
Cal 1-3
deg.   315 314.75 315.25
Injection quantity adjustment
Adjusting point   A
Rack position   8
Pump speed r/min   700 700 700
Average injection quantity mm3/st.   143.5 141.5 145.5
Max. variation between cylinders %   0 -3 3
Basic   *
Fixing the lever   *
Injection quantity adjustment_02
Adjusting point   B
Rack position   7.9
Pump speed r/min   500 500 500
Average injection quantity mm3/st.   140 137 143
Fixing the lever   *
Injection quantity adjustment_03
Adjusting point   D
Rack position   8.05
Pump speed r/min   1100 1100 1100
Average injection quantity mm3/st.   136.5 132.5 140.5
Fixing the lever   *
Injection quantity adjustment_04
Adjusting point   E
Rack position   7.6
Pump speed r/min   1200 1200 1200
Average injection quantity mm3/st.   122.5 117.5 127.5
Fixing the lever   *
Injection quantity adjustment_05
Adjusting point   F
Rack position   3.4+-0.5
Pump speed r/min   225 225 225
Average injection quantity mm3/st.   12 9 15
Max. variation between cylinders %   0 -10 10
Fixing the rack   *
Injection quantity adjustment_06
Adjusting point   G
Rack position   8.35+-0. 1
Pump speed r/min   330 330 330
Average injection quantity mm3/st.   149.5 143.5 155.5
Fixing the lever   *
Remarks
Startup boost setting
 
Injection quantity adjustment_07
Adjusting point   H
Rack position   -
Pump speed r/min   100 100 100
Average injection quantity mm3/st.   170 170 190
Fixing the lever   *
Remarks
After startup boost setting
 
Timer adjustment
Pump speed r/min   570--
Advance angle deg.   0 0 0
Load   0/5
Remarks
Start
 
Timer adjustment_02
Pump speed r/min   520
Advance angle deg.   0.3
Load   0/5
Timer adjustment_03
Pump speed r/min   900+50
Advance angle deg.   2 1.7 2.3
Load   4/5
Timer adjustment_04
Pump speed r/min   1100-50
Advance angle deg.   6.75 6.45 7.05
Load   5/5
Remarks
Finish
 

Test data Ex:

Governor adjustment

Test data 106873-3522
N:Pump speed R:Rack position (mm) (1)Lever ratio: RT (2)Target shim dimension: TH (3)Tolerance for racks not indicated: +-0.05mm. (4)Excess fuel setting for starting: SXL (5)Damper spring setting (6)Set idle at point K (N = N1, R = R1) and confirm that the injection quantity does not exceed Q1 at point J (N = N2). (7)Variable speed specification: idling adjustment (8)Main spring setting
----------
RT=0.8 TH=2.8mm SXL=8.35+-0.1mm N1=300r/min R1=3.4mm N2=1100r/min Q1=3mm3/st
----------

Speed control lever angle

Test data 106873-3522
F:Full speed I:Idle (1)Set the pump speed at aa (2)Set the pump speed at bb. (3)Stopper bolt setting (4)Stopper bolt setting
----------
aa=1290r/min bb=700r/min
----------
a=14.5deg+-5deg b=(12deg)+-5deg

0000000901

Test data 106873-3522
F:Full load I:Idle (1)Use the hole at R = aa (2)Stopper bolt setting
----------
aa=42mm
----------
a=39deg+-5deg b=39.5deg+-3deg

Stop lever angle

Test data 106873-3522
N:Pump normal S:Stop the pump. (1)Rack position = aa (set before setting excess fuel for starting) (2)Set the stopper bolt (apply red paint). (3)Use the hole at R = bb
----------
aa=12+0.5mm bb=37mm
----------
a=17.5deg+-5deg b=35deg+-5deg

0000001201

Test data 106873-3522
(1)Minimum - maximum speed specification (2)Variable speed specification
----------

----------
a=(14deg)+-5deg b=(30deg)

0000001501 LEVER

Test data 106873-3522
2-stage changeover lever adjustment (A) Speed lever (B) Load lever (C) 2-stage changeover lever (D) Link (E) Bolt (G) Variable speed specifications (H) Minimum maximum speed specifications F:Full speed I:Idle 1. Minimum-maximum speed specification adjustment (when running) (1)After completing governor adjustment, hold the 2-stage changeover lever (C) so that the speed lever (A) contacts the full speed stopper. (2)In this condition, the load lever is held in the idle position. (3)Adjust bolt (E) so that the clearance between the pin underneath lever (C) and the end of the long groove in link (D) is L. (4)Lock using the nut. 2. Variable speed specification adjustment (at operation) (1)Hold the 2-stage changeover lever (C) so that the load lever (B) contacts the full load stopper. (When the load lever is equipped with a cancel mechanism, move it so that it contacts the stopper without canceling.) (2)In this condition, confirm that the speed lever (A) moves from idle to full speed.
----------
L=1~2mm
----------

Timing setting

Test data 106873-3522
(1)Pump vertical direction (2)Coupling's key groove position at No 1 cylinder's beginning of injection (3)- (4)-
----------

----------
a=(80deg)




Have questions with 106873-3522?





Group cross 106873-3522 ZEXEL

Hino 

F 01G 09U 0B9 
220009360A 
INJECTION-PUMP ASSEMBLY
F-2
F 01G 09U 0BA 
220009360B 
INJECTION-PUMP ASSEMBLY
F-2
9 400 611 028 
220009361A 
INJECTION-PUMP ASSEMBLY
F-2
F 01G 09U 0BB 
220009370A 
INJECTION-PUMP ASSEMBLY
F-2
9 400 619 962 
220009370B 
INJECTION-PUMP ASSEMBLY
F-2
9 400 619 963 
220009371A 
INJECTION-PUMP ASSEMBLY
F-2
9 400 618 439 
220009372A 
INJECTION-PUMP ASSEMBLY
F-2
F 01G 09U 0BC 
220801770A 
INJECTION-PUMP ASSEMBLY
F-2
F 01G 09U 0BD 
220801770B 
INJECTION-PUMP ASSEMBLY
F-2
106873-3522  
9 400 618 440 
220801771A 
INJECTION-PUMP ASSEMBLY
F-2
 
220009380A 
INJECTION-PUMP ASSEMBLY
F-2
F 019 Z10 254 
220009380B 
INJECTION-PUMP ASSEMBLY
F-2
9 400 611 029 
220009381A 
INJECTION-PUMP ASSEMBLY
F-2
9 400 618 441 
220009382A 
INJECTION-PUMP ASSEMBLY
F-2
 
220009390A 
INJECTION-PUMP ASSEMBLY
F-2
 
 
INJECTION-PUMP ASSEMBLY

Hino 

9 400 618 442 
220009391A 
INJECTION-PUMP ASSEMBLY
F-2
 
 
INJECTION-PUMP ASSEMBLY

Hino 

 
220400664A 
INJECTION-PUMP ASSEMBLY
YJ40
 
 
INJECTION-PUMP ASSEMBLY

Hino 

 
220400666A 
INJECTION-PUMP ASSEMBLY
YJ42
 
220400665A 
INJECTION-PUMP ASSEMBLY
YJ41
9 400 618 443 
220009840A 
INJECTION-PUMP ASSEMBLY
YJ41
F 019 Z10 209 
220800068A 
INJECTION-PUMP ASSEMBLY
YJ41
9 400 618 444 
220801800A 
INJECTION-PUMP ASSEMBLY
YJ41
 
220009400A 
INJECTION-PUMP ASSEMBLY
F20C
 
 
INJECTION-PUMP ASSEMBLY

Hino 

9 400 618 445 
220009401A 
INJECTION-PUMP ASSEMBLY
F20C
Back to top