106873-3101 ZEXEL INJECTION-PUMP ASSEMBLY Calibration Data 1068733101 220007881a

Information Cross number Calibration Data Calibration Data Ex

Price: query
Buy now
Add to cart Go to cart

Rating:

Buy INJECTION-PUMP ASSEMBLY 106873-3101 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

ZEXEL 106873-3101 1068733101

HINO 220007881A 220007881a

Cross reference number

ZEXEL 106873-3101 1068733101

HINO 220007881A 220007881a

Zexel num

Bosch num

Firm num

Name

106873-3101
106873-3102

220007881A HINO

INJECTION-PUMP ASSEMBLY
F17E-B * K

Calibration Data:

Adjustment conditions

Test oil
1404 Test oil ISO4113 or {SAEJ967d}

Test oil temperature degC 40 40 45

Nozzle and nozzle holder 105780-8140

Bosch type code EF8511/9A

Nozzle 105780-0000

Bosch type code DN12SD12T

Nozzle holder 105780-2080

Bosch type code EF8511/9

Opening pressure MPa 17.2

Opening pressure kgf/cm2 175

Injection pipe
Outer diameter - inner diameter - length (mm) mm 8-3-600

Overflow valve 134424-0820

Overflow valve opening pressure kPa 127 107 147

Overflow valve opening pressure kgf/cm2 1.3 1.1 1.5

Tester oil delivery pressure kPa 157 157 157

Tester oil delivery pressure kgf/cm2 1.6 1.6 1.6

Direction of rotation (viewed from drive side)
Right R

Injection timing adjustment

Direction of rotation (viewed from drive side)
Right R

Injection order 1-8-6-2- 7-5-4-3

Pre-stroke mm 4.8 4.74 4.8

Beginning of injection position
Drive side NO.1

Difference between angles 1
Cal 1-8 deg. 45 44.75 45.25

Difference between angles 2
Cal 1-6 deg. 90 89.75 90.25

Difference between angles 3
Cyl.1-2 deg. 135 134.75 135.25

Difference between angles 4
Cal 1-7 deg. 180 179.75 180.25

Difference between angles 5
Cal 1-5 deg. 225 224.75 225.25

Difference between angles 6
Cal 1-4 deg. 270 269.75 270.25

Difference between angles 7
Cal 1-3 deg. 315 314.75 315.25

Injection quantity adjustment

Adjusting point A

Rack position 8.9

Pump speed r/min 700 700 700

Average injection quantity mm3/st. 139.3 137.3 141.3

Max. variation between cylinders % 0 -2 2

Basic *

Fixing the lever *

Injection quantity adjustment_02

Adjusting point B

Rack position 8.95+-0. 5

Pump speed r/min 1100 1100 1100

Average injection quantity mm3/st. 133.1 129.1 137.1

Fixing the lever *

Injection quantity adjustment_03

Adjusting point F

Rack position 3.8+-0.5

Pump speed r/min 225 225 225

Average injection quantity mm3/st. 10.4 7.4 13.4

Max. variation between cylinders % 0 -15 15

Fixing the rack *

Injection quantity adjustment_04

Adjusting point G

Rack position -

Pump speed r/min 100 100 100

Average injection quantity mm3/st. 139 139

Fixing the lever *

Remarks
After startup boost setting

Timer adjustment

Pump speed r/min 750--

Advance angle deg. 0 0 0

Load 1/4

Remarks
Start

Timer adjustment_02

Pump speed r/min 700

Advance angle deg. 0.3

Load 1/4

Timer adjustment_03

Pump speed r/min 820--

Advance angle deg. 0.7 0.4 1

Load 4/4

Timer adjustment_04

Pump speed r/min 900+50

Advance angle deg. 0.7 0.4 1

Load 3/4

Timer adjustment_05

Pump speed r/min 1100-50

Advance angle deg. 5.25 4.95 5.55

Load 4/4

Remarks
Finish

Test data Ex:

Governor adjustment

N:Pump speed R:Rack position (mm) (1)Tolerance for racks not indicated: +-0.05mm. (2)Set idle at point K (N = N1, R = R1) and confirm that the injection quantity does not exceed Q1 at point J (N = N2). (3)Excess fuel setting for starting: SXL (4)Damper spring setting
----------
N1=325r/min R1=3.8mm N2=1100r/min Q1=3mm3/st SXL=10.25+-0.1mm
----------

Speed control lever angle

F:Full speed
----------

----------
a=15.5deg+-5deg

0000000901

F:Full load I:Idle (1)Use the hole at R = aa (2)Stopper bolt setting
----------
aa=39mm
----------
a=39deg+-5deg b=43.5deg+-3deg

Stop lever angle

N:Pump normal S:Stop the pump. (1)Rack position = aa (at delivery), set before governor adjustment (2)Set the stopper bolt (apply red paint). (3)Use the pin at R = bb (4)Lever free
----------
aa=12+-0.1mm bb=37mm
----------
a=(9deg)+-5deg b=9deg+-5deg c=35deg+-5deg