106873-3081 ZEXEL INJECTION-PUMP ASSEMBLY Calibration Data 1068733081 220007791a


106873-3081 INJECTION-PUMP ASSEMBLY
Rating:
65
Buy INJECTION-PUMP ASSEMBLY 106873-3081 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

ZEXEL 106873-3081 1068733081
HINO 220007791A 220007791a

Cross reference number

ZEXEL 106873-3081 1068733081
HINO 220007791A 220007791a


Zexel num
Bosch num
Firm num
Name
106873-3081 
106873-3082 
 
220007791A  HINO
INJECTION-PUMP ASSEMBLY
F20C-B * K

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil
  ISO4113 or {SAEJ967d}
Test oil temperature degC   40 40 45
Nozzle and nozzle holder   105780-8140
Bosch type code   EF8511/9A
Nozzle   105780-0000
Bosch type code   DN12SD12T
Nozzle holder   105780-2080
Bosch type code   EF8511/9
Opening pressure MPa   17.2
Opening pressure kgf/cm2   175
Injection pipe
Outer diameter - inner diameter - length (mm)
mm   8-3-600
Overflow valve   134424-0820
Overflow valve opening pressure kPa   127 107 147
Overflow valve opening pressure kgf/cm2   1.3 1.1 1.5
Tester oil delivery pressure kPa   157 157 157
Tester oil delivery pressure kgf/cm2   1.6 1.6 1.6
Direction of rotation (viewed from drive side)
Right
  R
Injection timing adjustment
Direction of rotation (viewed from drive side)
Right
  R
Injection order   1-8-6-2- 7-5-4-3
Pre-stroke mm   4.5 4.44 4.5
Beginning of injection position
Drive side
  NO.1
Difference between angles 1
Cal 1-8
deg.   45 44.75 45.25
Difference between angles 2
Cal 1-6
deg.   90 89.75 90.25
Difference between angles 3
Cyl.1-2
deg.   135 134.75 135.25
Difference between angles 4
Cal 1-7
deg.   180 179.75 180.25
Difference between angles 5
Cal 1-5
deg.   225 224.75 225.25
Difference between angles 6
Cal 1-4
deg.   270 269.75 270.25
Difference between angles 7
Cal 1-3
deg.   315 314.75 315.25
Injection quantity adjustment
Adjusting point   A
Rack position   9.2
Pump speed r/min   700 700 700
Average injection quantity mm3/st.   157.6 155.6 159.6
Max. variation between cylinders %   0 -2 2
Basic   *
Fixing the lever   *
Injection quantity adjustment_02
Adjusting point   B
Rack position   9.1
Pump speed r/min   500 500 500
Average injection quantity mm3/st.   160.7 157.7 163.7
Fixing the lever   *
Injection quantity adjustment_03
Adjusting point   D
Rack position   9.25+-0. 5
Pump speed r/min   1100 1100 1100
Average injection quantity mm3/st.   143.7 139.7 147.7
Fixing the lever   *
Injection quantity adjustment_04
Adjusting point   E
Rack position   8.5
Pump speed r/min   1200 1200 1200
Average injection quantity mm3/st.   129 126 132
Fixing the lever   *
Injection quantity adjustment_05
Adjusting point   F
Rack position   3.9+-0.5
Pump speed r/min   225 225 225
Average injection quantity mm3/st.   12.6 9.6 15.6
Max. variation between cylinders %   0 -15 15
Fixing the rack   *
Injection quantity adjustment_06
Adjusting point   G
Rack position   9.85+-0. 1
Pump speed r/min   300 300 300
Average injection quantity mm3/st.   178.5 174.5 182.5
Fixing the lever   *
Remarks
Startup boost setting
 
Injection quantity adjustment_07
Adjusting point   H
Rack position   -
Pump speed r/min   100 100 100
Average injection quantity mm3/st.   188 188 208
Fixing the lever   *
Remarks
After startup boost setting
 
Timer adjustment
Pump speed r/min   600--
Advance angle deg.   0 0 0
Load   1/4
Remarks
Start
 
Timer adjustment_02
Pump speed r/min   550
Advance angle deg.   0.3
Load   1/4
Timer adjustment_03
Pump speed r/min   700--
Advance angle deg.   1 0.7 1.3
Load   4/4
Timer adjustment_04
Pump speed r/min   900+50
Advance angle deg.   1 0.7 1.3
Load   3/4
Timer adjustment_05
Pump speed r/min   1100-50
Advance angle deg.   4.75 4.45 5.05
Load   4/4
Remarks
Finish
 

Test data Ex:

Governor adjustment

Test data 106873-3081
N:Pump speed R:Rack position (mm) (1)Tolerance for racks not indicated: +-0.05mm. (2)Set idle at point K (N = N1, R = R1) and confirm that the injection quantity does not exceed Q1 at point J (N = N2). (3)Excess fuel setting for starting: SXL (4)Damper spring setting (5)When air cylinder is operating.
----------
N1=300r/min R1=3.9mm N2=1150r/min Q1=3mm3/st SXL=9.85+-0.1mm
----------

Speed control lever angle

Test data 106873-3081
F:Full speed
----------

----------
a=15.5deg+-5deg

0000000901

Test data 106873-3081
F:Full load I:Idle (1)When setting point K (at air cylinder operation) (2)Use the hole at R = aa (3)Stopper bolt setting
----------
aa=39mm
----------
a=39deg+-5deg b=43.5deg+-3deg c=(5deg)+-5deg

Stop lever angle

Test data 106873-3081
N:Pump normal S:Stop the pump. (1)Rack position = aa (at delivery), set before governor adjustment (2)Set the stopper bolt (apply red paint). (3)Use the pin at R = bb (4)Lever free
----------
aa=12+-0.1mm bb=37mm
----------
a=(9deg)+-5deg b=9deg+-5deg c=35deg+-5deg

0000001501 LEVER

Test data 106873-3081
1. Air cylinder adjustment (1)With the load lever in the idle position, temporarily set the distance between the load lever A and the air cylinder D at approximately L. (2)Set N1 and apply P1 to the air cylinder D. (3)Adjust set bolt (D) to obtain R1 at the same speed. (4)Lock using nut C. (5)Apply positive pressure several times. (6)Confirm that the load lever A returns to the idling position N2 at pressure P2. (7)Also at P1 confirm R1 (N1).
----------
L=(5)mm R1=3.9mm N1=300r/min N2=225r/min P1=392+98kPa(4+1kgf/cm2) P2=0kPa(0kgf/cm2)
----------

Timing setting

Test data 106873-3081
(1)Pump vertical direction (2)Coupling's key groove position at No 1 cylinder's beginning of injection (3)- (4)-
----------

----------
a=(80deg)




Have questions with 106873-3081?





Group cross 106873-3081 ZEXEL

Hino 

 
220007790A 
INJECTION-PUMP ASSEMBLY
F20C-B
106873-3081  

106873-3082 
 
220007791A 
INJECTION-PUMP ASSEMBLY
F20C-B
 
220007792A 
INJECTION-PUMP ASSEMBLY
F20C-B
 
 
INJECTION-PUMP ASSEMBLY

Hino 

 
220007792B 
INJECTION-PUMP ASSEMBLY
F20C-B
9 400 618 413 
220007792C 
INJECTION-PUMP ASSEMBLY
F20C-B
Back to top