106871-8670 ZEXEL INJECTION-PUMP ASSEMBLY Calibration Data 1068718670 220400084a

Information Cross number Calibration Data Calibration Data Ex

Price: query
Buy now
Add to cart Go to cart

Rating:

Buy INJECTION-PUMP ASSEMBLY 106871-8670 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

ZEXEL 106871-8670 1068718670

HINO 220400084A 220400084a

Cross reference number

ZEXEL 106871-8670 1068718670

HINO 220400084A 220400084a

Zexel num

Bosch num

Firm num

Name

106871-8670

220400084A HINO

INJECTION-PUMP ASSEMBLY
F17E * K

Calibration Data:

Adjustment conditions

Test oil
1404 Test oil ISO4113 or {SAEJ967d}

Test oil temperature degC 40 40 45

Nozzle and nozzle holder 105780-8140

Bosch type code EF8511/9A

Nozzle 105780-0000

Bosch type code DN12SD12T

Nozzle holder 105780-2080

Bosch type code EF8511/9

Opening pressure MPa 17.2

Opening pressure kgf/cm2 175

Injection pipe
Outer diameter - inner diameter - length (mm) mm 8-3-600

Overflow valve 134424-0820

Overflow valve opening pressure kPa 127 107 147

Overflow valve opening pressure kgf/cm2 1.3 1.1 1.5

Tester oil delivery pressure kPa 157 157 157

Tester oil delivery pressure kgf/cm2 1.6 1.6 1.6

Direction of rotation (viewed from drive side)
Right R

Injection timing adjustment

Direction of rotation (viewed from drive side)
Right R

Injection order 1-8-6-2- 7-5-4-3

Pre-stroke mm 4.8 4.74 4.8

Beginning of injection position
Drive side NO.1

Difference between angles 1
Cal 1-8 deg. 45 44.75 45.25

Difference between angles 2
Cal 1-6 deg. 90 89.75 90.25

Difference between angles 3
Cyl.1-2 deg. 135 134.75 135.25

Difference between angles 4
Cal 1-7 deg. 180 179.75 180.25

Difference between angles 5
Cal 1-5 deg. 225 224.75 225.25

Difference between angles 6
Cal 1-4 deg. 270 269.75 270.25

Difference between angles 7
Cal 1-3 deg. 315 314.75 315.25

Injection quantity adjustment

Adjusting point A

Rack position 9

Pump speed r/min 700 700 700

Average injection quantity mm3/st. 139 137 141

Max. variation between cylinders % 0 -2 2

Basic *

Fixing the lever *

Injection quantity adjustment_02

Adjusting point B

Rack position 9.2

Pump speed r/min 1100 1100 1100

Average injection quantity mm3/st. 140 137 143

Fixing the lever *

Injection quantity adjustment_03

Adjusting point F

Rack position 3.9+-0.5

Pump speed r/min 225 225 225

Average injection quantity mm3/st. 9.7 6.7 12.7

Max. variation between cylinders % 0 -15 15

Fixing the rack *

Injection quantity adjustment_04

Adjusting point G

Rack position -

Pump speed r/min 100 100 100

Average injection quantity mm3/st. 140 140

Fixing the lever *

Remarks
After startup boost setting

Timer adjustment

Pump speed r/min 710--

Advance angle deg. 0 0 0

Load 1/4

Remarks
Start

Timer adjustment_02

Pump speed r/min 660

Advance angle deg. 0.3

Load 1/4

Timer adjustment_03

Pump speed r/min 800

Advance angle deg. 0.7 0.4 1

Load 4/4

Timer adjustment_04

Pump speed r/min 880

Advance angle deg. 0.7 0.4 1

Load 3/4

Timer adjustment_05

Pump speed r/min 1100

Advance angle deg. 5.25 4.95 5.55

Load 4/4

Remarks
Finish

Test data Ex:

Governor adjustment

N:Pump speed R:Rack position (mm) (1)Tolerance for racks not indicated: +-0.05mm. (2)Supplied with torque spring not set. (3)Set idle at point K (N = N1, R = R1) and confirm that the injection quantity at N = N2 at point J is Q1. (4)Excess fuel setting for starting: SXL (N = N3) (5)Damper spring setting
----------
N1=325r/min R1=3.9mm N2=1100r/min Q1=2mm3/st SXL=10+-0.1mm N3=300r/min
----------

Speed control lever angle

F:Full speed
----------

----------
a=(16deg)+-5deg

0000000901

F:Full load I:Idle (1)Use the hole at R = aa (2)Stopper bolt setting
----------
aa=65mm
----------
a=10deg+-5deg b=44deg+-3deg

Stop lever angle

N:Engine manufacturer's normal use S:Stop the pump. (1)Rack position = aa (2)Rack position bb (3)Set the stopper bolt (apply red paint). (4)Free (at delivery)
----------
aa=12mm bb=2.5-0.5mm
----------
a=1deg+-5deg b=27.5deg+-5deg c=(34deg)

0000001501 RACK SENSOR

(VR) measurement voltage (I) Part number of the control unit (G) Apply red paint. (H): End surface of the pump 1. Rack sensor adjustment (-0620) (1)Fix the speed control lever at the full position (2)Set the speed to N1 r/min. (If the boost compensator is provided, apply boost pressure.) (3)Adjust the bobbin (A) so that the rack sensor's output voltage is VR+-0.01. (4)At that time, rack position must be Ra. (5)Apply G at two places. Connecting part between the joint (B) and the nut (F) Connecting part between the joint (B) and the end surface of the pump (H)
----------
N1=1100r/min Ra=9.2mm
----------