106871-4340 ZEXEL INJECTION-PUMP ASSEMBLY Calibration Data 1068714340

Information Cross number Calibration Data Calibration Data Ex

Price: query
Buy now
Add to cart Go to cart

Rating:

Buy INJECTION-PUMP ASSEMBLY 106871-4340 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

ZEXEL 106871-4340 1068714340

Cross reference number

ZEXEL 106871-4340 1068714340

Zexel num

Bosch num

Firm num

Name

106871-4340
106871-4341

DPICO

INJECTION-PUMP ASSEMBLY
RF8 * Q

Calibration Data:

Adjustment conditions

Test oil
1404 Test oil ISO4113 or {SAEJ967d}

Test oil temperature degC 40 40 45

Nozzle and nozzle holder 105780-8140

Bosch type code EF8511/9A

Nozzle 105780-0000

Bosch type code DN12SD12T

Nozzle holder 105780-2080

Bosch type code EF8511/9

Opening pressure MPa 17.2

Opening pressure kgf/cm2 175

Injection pipe
Outer diameter - inner diameter - length (mm) mm 8-3-600

Overflow valve 132424-0620

Overflow valve opening pressure kPa 157 157 157

Overflow valve opening pressure kgf/cm2 1.6 1.6 1.6

Tester oil delivery pressure kPa 157 157 157

Tester oil delivery pressure kgf/cm2 1.6 1.6 1.6

Direction of rotation (viewed from drive side)
Right R

Injection timing adjustment

Direction of rotation (viewed from drive side)
Right R

Injection order 1-8-7-5- 4-3-6-2

Pre-stroke mm 3.65 3.6 3.7

Beginning of injection position
Governor side No.1

Difference between angles 1
Cal 1-8 deg. 45 44.5 45.5

Difference between angles 2
Cal 1-7 deg. 90 89.5 90.5

Difference between angles 3
Cal 1-5 deg. 135 134.5 135.5

Difference between angles 4
Cal 1-4 deg. 180 179.5 180.5

Difference between angles 5
Cal 1-3 deg. 225 224.5 225.5

Difference between angles 6
Cal 1-6 deg. 270 269.5 270.5

Difference between angles 7
Cyl.1-2 deg. 315 314.5 315.5

Injection quantity adjustment

Adjusting point A

Rack position 9.7

Pump speed r/min 700 700 700

Average injection quantity mm3/st. 125.5 124.5 126.5

Max. variation between cylinders % 0 -4 4

Basic *

Fixing the lever *

Injection quantity adjustment_02

Adjusting point C

Rack position 6.1+-0.5

Pump speed r/min 280 280 280

Average injection quantity mm3/st. 11.5 9.5 13.5

Max. variation between cylinders % 0 -10 10

Fixing the rack *

Injection quantity adjustment_03

Adjusting point D

Rack position -

Pump speed r/min 100 100 100

Average injection quantity mm3/st. 130 130 150

Fixing the lever *

Remarks
After startup boost setting

Timer adjustment

Pump speed r/min 800--

Advance angle deg. 0 0 0

Remarks
Start

Timer adjustment_02

Pump speed r/min 750

Advance angle deg. 0.3

Timer adjustment_03

Pump speed r/min 1100

Advance angle deg. 4 3.7 4.3

Remarks
Finish

Test data Ex:

Governor adjustment

N:Pump speed R:Rack position (mm) (1)Adjust governor at speed not exceeding N = N1. Output voltage VR+-0.01 (V), speed N1 r/min, governor Vist = V1 (V) (2)Tolerance for racks not indicated: +-0.05mm. (3)Lever ratio: RT (4)Target shim dimension: TH (5)Excess fuel setting for starting: SXL (N = N2) (6)Damper spring setting (7)Variable speed specification: idling adjustment (8)Fix the lever at the full-load position at delivery. (9)Main spring setting
----------
N1=1710r/min RT=1 TH=2.8mm SXL=10.2+-0.1mm N2=400r/min
----------

Speed control lever angle

F:Full speed I:Idle (1)Set the stopper bolt (fixed at full-load position at delivery.) (2)Pump speed = aa
----------
aa=290r/min
----------
a=(6deg)+-5deg b=(17deg)+-5deg

0000000901

F:Full load I:Idle (1)Stopper bolt setting (2)Use the hole at R = aa
----------
aa=64.3mm
----------
a=18.5deg+-5deg b=26.5deg+-3deg

Stop lever angle

N:Pump normal S:Stop the pump. (1)Use the pin at R = aa (2)Drive side
----------
aa=28mm
----------
a=12deg+-5deg b=64deg+-5deg

Timing setting

(1)Pump vertical direction (2)Position of the coupling key groove at the beginning of injection of the No. 8 cylinder.
----------

----------
a=(90deg)