106871-3190 ZEXEL INJECTION-PUMP ASSEMBLY Calibration Data 1068713190 220001641a

Information Cross number Calibration Data Calibration Data Ex

Price: query
Buy now
Add to cart Go to cart

Rating:

Buy INJECTION-PUMP ASSEMBLY 106871-3190 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

ZEXEL 106871-3190 1068713190

HINO 220001641A 220001641a

Cross reference number

ZEXEL 106871-3190 1068713190

HINO 220001641A 220001641a

Zexel num

Bosch num

Firm num

Name

106871-3190
106871-3191

220001641A HINO

INJECTION-PUMP ASSEMBLY
EF500 *

Calibration Data:

Adjustment conditions

Test oil
1404 Test oil ISO4113 or {SAEJ967d}

Test oil temperature degC 40 40 45

Nozzle and nozzle holder 105780-8140

Bosch type code EF8511/9A

Nozzle 105780-0000

Bosch type code DN12SD12T

Nozzle holder 105780-2080

Bosch type code EF8511/9

Opening pressure MPa 17.2

Opening pressure kgf/cm2 175

Injection pipe
Outer diameter - inner diameter - length (mm) mm 8-3-600

Overflow valve 134424-0820

Overflow valve opening pressure kPa 127 107 147

Overflow valve opening pressure kgf/cm2 1.3 1.1 1.5

Tester oil delivery pressure kPa 157 157 157

Tester oil delivery pressure kgf/cm2 1.6 1.6 1.6

Direction of rotation (viewed from drive side)
Right R

Injection timing adjustment

Direction of rotation (viewed from drive side)
Right R

Injection order 1-8-6-2- 7-5-4-3

Pre-stroke mm 4 3.9 4

Beginning of injection position
Drive side NO.1

Difference between angles 1
Cal 1-8 deg. 45 44.5 45.5

Difference between angles 2
Cal 1-6 deg. 90 89.5 90.5

Difference between angles 3
Cyl.1-2 deg. 135 134.5 135.5

Difference between angles 4
Cal 1-7 deg. 180 179.5 180.5

Difference between angles 5
Cal 1-5 deg. 225 224.5 225.5

Difference between angles 6
Cal 1-4 deg. 270 269.5 270.5

Difference between angles 7
Cal 1-3 deg. 315 314.5 315.5

Injection quantity adjustment

Adjusting point A

Rack position 9.1

Pump speed r/min 500 500 500

Average injection quantity mm3/st. 107.2 104.2 110.2

Max. variation between cylinders % 0 -4 4

Fixing the lever *

Injection quantity adjustment_02

Adjusting point B

Rack position 9.2

Pump speed r/min 700 700 700

Average injection quantity mm3/st. 111 109 113

Max. variation between cylinders % 0 -2 2

Basic *

Fixing the lever *

Injection quantity adjustment_03

Adjusting point C

Rack position 6.4+-0.5

Pump speed r/min 225 225 225

Average injection quantity mm3/st. 13.7 10.7 16.7

Max. variation between cylinders % 0 -15 15

Fixing the rack *

Injection quantity adjustment_04

Adjusting point D

Rack position -

Pump speed r/min 50 50 50

Average injection quantity mm3/st. 122 112 132

Fixing the lever *

Remarks
After startup boost setting

Injection quantity adjustment_05

Adjusting point E

Rack position -

Pump speed r/min 1000 1000 1000

Average injection quantity mm3/st. 0

Fixing the lever *

Timer adjustment

Pump speed r/min 950+-50

Advance angle deg. 0 0 0

Remarks
Start

Timer adjustment_02

Pump speed r/min 1100

Advance angle deg. 1 0.5 1.5

Timer adjustment_03

Pump speed r/min 1200

Advance angle deg. 2 1.5 2.5

Remarks
Finish

Test data Ex:

Governor adjustment

N:Pump speed R:Rack position (mm) (1)Beginning of damper spring operation: DL (2)Set idle at point F (N = N1, R = R1) and confirm that the injection quantity at N = N2 is at point E (or less. (3)Set the load control lever's stop position at R = aa (N = 0). (4)Excess fuel setting for starting: SXL
----------
DL=5.4-0.2mm N1=300r/min R1=5.4mm N2=1000r/min Q1=0mm3st aa=5.8+0.2mm SXL=9.7+0.2mm
----------

Speed control lever angle

F:Full speed
----------

----------
a=0deg+-5deg

0000000901

F:Full load I:Idle S:Stop
----------

----------
a=32deg+-5deg b=33deg+-3deg c=19deg+4deg-5deg

0000001501 MICRO SWITCH

Switch adjustment Adjust the bolt so that the lower lever position is obtained when the switch is turned ON. (1)Speed N1 (2)Rack position Ra
----------
N1=325-25r/min Ra=6.4mm
----------