106871-1152 ZEXEL 9 400 612 915 BOSCH INJECTION-PUMP ASSEMBLY 9400612915 1068711152 1156031792


106871-1152 INJECTION-PUMP ASSEMBLY
Rating:
8
Buy INJECTION-PUMP ASSEMBLY 106871-1152 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

BOSCH 9 400 612 915 9400612915
ZEXEL 106871-1152 1068711152
ISUZU 1156031792 1156031792

Service parts 106871-1152 INJECTION-PUMP ASSEMBLY:

1. _
2. FUEL INJECTION PUMP 106081-9090
3. GOVERNOR 105923-2850
4. SUPPLY PUMP 105237-5280
5. AUTOM. ADVANCE MECHANIS 105693-0550
6. COUPLING PLATE
7. COUPLING PLATE
8. _
9. _
10. NOZZLE AND HOLDER ASSY 105101-7750
11. Nozzle and Holder 1-15300-328-0
12. Open Pre:MPa(Kqf/cm2) 15.7{160}/22.1{225}
13. NOZZLE-HOLDER 105030-3540
14. NOZZLE 105025-0090
15. NOZZLE SET

Include in #1:

106871-1152 as INJECTION-PUMP ASSEMBLY

Cross reference number

BOSCH 9 400 612 915 9400612915
ZEXEL 106871-1152 1068711152
ISUZU 1156031792 1156031792


Zexel num
Bosch num
Firm num
Name
106871-1152 
9 400 612 915 
1156031792  ISUZU
INJECTION-PUMP ASSEMBLY
8PE1-S K 14CD INJECTION PUMP ASSY PE8P PE

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil
  ISO4113 or {SAEJ967d}
Test oil temperature degC   40 40 45
Nozzle and nozzle holder   105780-8250
Bosch type code   1 688 901 101
Nozzle   105780-0120
Bosch type code   1 688 901 990
Nozzle holder   105780-2190
Opening pressure MPa   20.7
Opening pressure kgf/cm2   211
Injection pipe
Outer diameter - inner diameter - length (mm)
mm   8-3-600
Overflow valve   134424-4320
Overflow valve opening pressure kPa   255 255 255
Overflow valve opening pressure kgf/cm2   2.6 2.6 2.6
Tester oil delivery pressure kPa   255 255 255
Tester oil delivery pressure kgf/cm2   2.6 2.6 2.6
Direction of rotation (viewed from drive side)
Right
  R
Injection timing adjustment
Direction of rotation (viewed from drive side)
Right
  R
Injection order   1-8-7-3- 6-5-4-2
Pre-stroke mm   5.5 5.47 5.53
Rack position
Point A
  R=A
Beginning of injection position
Governor side
  NO.1
Difference between angles 1
Cal 1-8
deg.   45 44.75 45.25
Difference between angles 2
Cal 1-7
deg.   90 89.75 90.25
Difference between angles 3
Cal 1-3
deg.   135 134.75 135.25
Difference between angles 4
Cal 1-6
deg.   180 179.75 180.25
Difference between angles 5
Cal 1-5
deg.   225 224.75 225.25
Difference between angles 6
Cal 1-4
deg.   270 269.75 270.25
Difference between angles 7
Cyl.1-2
deg.   315 314.75 315.25
Injection quantity adjustment
Adjusting point   -
Rack position   12.1
Pump speed r/min   700 700 700
Average injection quantity mm3/st.   145 143.4 146.6
Max. variation between cylinders %   0 -3 3
Basic   *
Fixing the rack   *
Standard for adjustment of the maximum variation between cylinders   *
Injection quantity adjustment_02
Adjusting point   Z
Rack position   6.7+-0.5
Pump speed r/min   420 420 420
Average injection quantity mm3/st.   13.5 11.5 15.5
Max. variation between cylinders %   0 -13 13
Fixing the rack   *
Standard for adjustment of the maximum variation between cylinders   *
Injection quantity adjustment_03
Adjusting point   A
Rack position   R1(12.1)
Pump speed r/min   700 700 700
Average injection quantity mm3/st.   145 144 146
Basic   *
Fixing the lever   *

Test data Ex:

Governor adjustment

Test data 106871-1152
N:Pump speed R:Rack position (mm) (1)Torque cam stamping: T1 (2)Tolerance for racks not indicated: +-0.05mm. (3)Damper spring setting
----------
T1=AD63
----------

Timer adjustment

Test data 106871-1152
(1)Adjusting range (2)Step response time (N): Speed of the pump (L): Load (theta) Advance angle (Srd1) Step response time 1 (Srd2) Step response time 2 1. Adjusting conditions for the variable timer (1)Adjust the clearance between the pickup and the protrusion to L.
----------
L=1-0.2mm N2=800r/min C2=(8)deg t1=1.5--sec. t2=1.5--sec.
----------
N1=950++r/min P1=0kPa(0kgf/cm2) P2=392kPa(4kgf/cm2) C1=8+-0.3deg R01=0/4load R02=4/4load

Speed control lever angle

Test data 106871-1152
F:Full speed I:Idle (1)Use the pin at R = aa (2)Stopper bolt setting
----------
aa=42.5mm
----------
a=23deg+-5deg b=(32deg)+-3deg

Stop lever angle

Test data 106871-1152
N:Pump normal S:Stop the pump. (1)Use the pin at R = aa (2)Set the stopper bolt so that speed = bb and rack position = cc. (Confirm non-injection.)
----------
aa=40mm bb=0r/min cc=1.5+-0.3mm
----------
a=20deg+-5deg b=43deg+-5deg

0000001501 RACK SENSOR

Test data 106871-1152
Rack sensor adjustment 1. Flange type rack sensor (rack sensor adjustment -5*20) (1)These types of rack sensors do not need adjustment. Confirm the performance with the following procedures. (2)Mount the rack sensor main body to the pump main body. (3)Fix the pump lever at full. (4)At supply voltage V1, pump speed N1 and rack position Ra, confirm that the amp's output voltage is Vist. (5)Move the pump lever two or three times. (6)Set again to full. (7)Confirm that the amplifier output voltage is Vist. (8)Fix the caution plate to the upper part of the rack sensor. (For those without the caution plate instructions, make sure the nameplate of the rack sensor carries the "Don't hold here" caution.) (9)Apply red paint to the rack sensor mounting bolts (2 places).
----------
V1=5+-0.01V N1=1050r/min Ra=R1(12.1)+0.85mm Vist=1.35+-0.14V
----------

Timing setting

Test data 106871-1152
(1)Pump vertical direction (2)Position of "Z" mark at the No 1 cylinder's beginning of injection (governor side) (3)B.T.D.C.: aa (4)-
----------
aa=4deg
----------
a=(180deg)




Have questions with 106871-1152?





Group cross 106871-1152 ZEXEL

9 400 611 014 
 
INJECTION-PUMP ASSEMBLY
8PE1-RA

Isuzu 

9 400 611 014 
1156029700 
INJECTION-PUMP ASSEMBLY
8PE1-RA
 
1156030310 
INJECTION-PUMP ASSEMBLY
8PE1-S
 
1156030311 
INJECTION-PUMP ASSEMBLY
8PE1-S
 
1156030312 
INJECTION-PUMP ASSEMBLY
8PE1-S
9 400 618 071 
1156030313 
INJECTION-PUMP ASSEMBLY
8PE1-S
 
 
INJECTION-PUMP ASSEMBLY

Isuzu 

 
1156029840 
INJECTION-PUMP ASSEMBLY
8PE1
 
1156029841 
INJECTION-PUMP ASSEMBLY
8PE1
 
1156029842 
INJECTION-PUMP ASSEMBLY
8PE1
 
 
INJECTION-PUMP ASSEMBLY

Isuzu 

9 400 612 957 
1156029843 
INJECTION-PUMP ASSEMBLY
8PE1
 
 
INJECTION-PUMP ASSEMBLY

Isuzu 

 
1156030320 
INJECTION-PUMP ASSEMBLY
8PE1-S
 
1156030321 
INJECTION-PUMP ASSEMBLY
8PE1-S
 
1156030322 
INJECTION-PUMP ASSEMBLY
8PE1-S
 
1156030323 
INJECTION-PUMP ASSEMBLY
8PE1-S
 
1156030324 
INJECTION-PUMP ASSEMBLY
8PE1-S
F 01G 09U 09H 
1156031660 
INJECTION-PUMP ASSEMBLY
8PE1-S
F 01G 09U 09J 
1156031661 
INJECTION-PUMP ASSEMBLY
8PE1-S
9 400 618 072 
1156031662 
INJECTION-PUMP ASSEMBLY
8PE1-S
 
1156031790 
INJECTION-PUMP ASSEMBLY
8PE1-S
 
1156031791 
INJECTION-PUMP ASSEMBLY
8PE1-S
106871-1152  
9 400 612 915 
1156031792 
INJECTION-PUMP ASSEMBLY
8PE1-S
F 01G 09U 09K 
1156031800 
INJECTION-PUMP ASSEMBLY
8PE1-S
F 01G 09U 09L 
1156031801 
INJECTION-PUMP ASSEMBLY
8PE1-S
9 400 618 073 
1156031802 
INJECTION-PUMP ASSEMBLY
8PE1-S
 
1156031810 
INJECTION-PUMP ASSEMBLY
8PE1-S
F 019 Z10 208 
1156031811 
INJECTION-PUMP ASSEMBLY
8PE1-S
9 400 618 074 
1156031812 
INJECTION-PUMP ASSEMBLY
8PE1-S
F 01G 09U 09M 
1156031890 
INJECTION-PUMP ASSEMBLY
8PE1-S
9 400 611 545 
1156031891 
INJECTION-PUMP ASSEMBLY
8PE1-S
F 01G 09U 09N 
1156031892 
INJECTION-PUMP ASSEMBLY
8PE1-S
9 400 618 075 
1156031893 
INJECTION-PUMP ASSEMBLY
8PE1-S
 
1156031990 
INJECTION-PUMP ASSEMBLY
8PE1
 
1156031991 
INJECTION-PUMP ASSEMBLY
8PE1
9 400 611 723 
1156031992 
INJECTION-PUMP ASSEMBLY
8PE1
9 400 618 076 
1156031993 
INJECTION-PUMP ASSEMBLY
8PE1
Back to top