106691-6791 ZEXEL INJECTION-PUMP ASSEMBLY Calibration Data 1066916791 1156009901

Information Cross number Calibration Data Calibration Data Ex

Price: query
Buy now
Add to cart Go to cart

Rating:

Buy INJECTION-PUMP ASSEMBLY 106691-6791 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

ZEXEL 106691-6791 1066916791

ISUZU 1156009901 1156009901

Cross reference number

ZEXEL 106691-6791 1066916791

ISUZU 1156009901 1156009901

Zexel num

Bosch num

Firm num

Name

106691-6791
106691-6792

1156009901 ISUZU

INJECTION-PUMP ASSEMBLY
6RA1 *

Calibration Data:

Adjustment conditions

Test oil
1404 Test oil ISO4113 or {SAEJ967d}

Test oil temperature degC 40 40 45

Nozzle and nozzle holder 105780-8140

Bosch type code EF8511/9A

Nozzle 105780-0000

Bosch type code DN12SD12T

Nozzle holder 105780-2080

Bosch type code EF8511/9

Opening pressure MPa 17.2

Opening pressure kgf/cm2 175

Injection pipe
Outer diameter - inner diameter - length (mm) mm 8-3-600

Overflow valve 132424-0620

Overflow valve opening pressure kPa 157 123 191

Overflow valve opening pressure kgf/cm2 1.6 1.25 1.95

Tester oil delivery pressure kPa 157 157 157

Tester oil delivery pressure kgf/cm2 1.6 1.6 1.6

Direction of rotation (viewed from drive side)
Right R

Injection timing adjustment

Direction of rotation (viewed from drive side)
Right R

Injection order 1-4-2-6- 3-5

Pre-stroke mm 3 2.95 3.05

Beginning of injection position
Drive side NO.1

Difference between angles 1
Cal 1-4 deg. 60 59.5 60.5

Difference between angles 2
Cyl.1-2 deg. 120 119.5 120.5

Difference between angles 3
Cal 1-6 deg. 180 179.5 180.5

Difference between angles 4
Cal 1-3 deg. 240 239.5 240.5

Difference between angles 5
Cal 1-5 deg. 300 299.5 300.5

Injection quantity adjustment

Adjusting point A

Rack position 7.7

Pump speed r/min 700 700 700

Average injection quantity mm3/st. 105.7 103.7 107.7

Max. variation between cylinders % 0 -3 3

Basic *

Fixing the lever *

Injection quantity adjustment_02

Adjusting point B

Rack position 5.5+-0.5

Pump speed r/min 225 225 225

Average injection quantity mm3/st. 12.6 9.4 15.8

Max. variation between cylinders % 0 -13 13

Fixing the rack *

Injection quantity adjustment_03

Adjusting point D

Rack position 7.3

Pump speed r/min 700 700 700

Average injection quantity mm3/st. 93 89 97

Max. variation between cylinders % 0 -3 3

Fixing the lever *

Remarks
At absolute pressure 74kPa {555 mmHg}

Injection quantity adjustment_04

Adjusting point E

Rack position 7.7

Pump speed r/min 1150 1150 1150

Average injection quantity mm3/st. 115.2 109.2 121.2

Max. variation between cylinders % 0 -3 3

Fixing the lever *

Timer adjustment

Pump speed r/min 700

Advance angle deg. 0.5

Timer adjustment_02

Pump speed r/min 800

Advance angle deg. 0.7 0.2 1.2

Timer adjustment_03

Pump speed r/min 1000

Advance angle deg. 2.7 2.2 3.2

Timer adjustment_04

Pump speed r/min 1150

Advance angle deg. 4 3.5 4.5

Timer adjustment_05

Pump speed r/min -

Advance angle deg. 4.5 4 5

Remarks
Measure the actual speed, stop

Test data Ex:

Governor adjustment

N:Pump speed R:Rack position (mm) (1)Beginning of damper spring operation: DL (2)Excess fuel setting for starting: SXL (3)Aneroid compensator absolute pressure: at P1
----------
DL=5-0.5mm SXL=7.7+0.2mm P1=74+-0.7kPa(555+-5mmHg)
----------

0000000901

F:Full load I:Idle S:Stop (1)Attach the return spring to the upper hole and adjust. (2)Set the load lever's stop position so that R = aa (N = 0).
----------
aa=5mm
----------
a=6.5deg+-5deg b=8deg+-5deg c=27deg+-3deg

Stop lever angle

N:Pump normal S:Stop the pump.
----------

----------
a=32deg+-5deg b=64deg+-5deg

0000001501 ACS

(A) Set screw (B) Push rod 1 1. Aneroid compensator unit adjustment (1)Screw in (A) to obtain L1. 2. Adjustment following governor installation (1)Set the speed of the pump to N1 r/min and fix the control lever at the full set position. (2)Screw in the aneroid compensator to obtain the performance shown in the graph above.
----------
N1=700r/min L1=(0.6~0.9)mm
----------
R1=7.7mm R2=7.3mm P1=(90.6)kPa((680)mmHg) P2=74+-0.7kPa(555+-5mmHg) Q1=105.7+-2cm3/1000st Q2=(93)+-2cm3/1000st

Timing setting

(1)Pump vertical direction (2)Position of timer's threaded hole at No 1 cylinder's beginning of injection (3)B.T.D.C.: aa (4)-
----------
aa=19deg
----------
a=(70deg)