106682-9401 ZEXEL INJECTION-PUMP ASSEMBLY Calibration Data 1066829401


106682-9401 INJECTION-PUMP ASSEMBLY
Rating:
31
Buy INJECTION-PUMP ASSEMBLY 106682-9401 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

ZEXEL 106682-9401 1066829401

Service parts 106682-9401 INJECTION-PUMP ASSEMBLY:

1. _
2. FUEL INJECTION PUMP 106068-2890
3. GOVERNOR 105447-1741
4. SUPPLY PUMP 105237-1541
5. AUTOM. ADVANCE MECHANIS
6. COUPLING PLATE 105664-0390
7. COUPLING PLATE
8. _
9. _
10. NOZZLE AND HOLDER ASSY 105111-4640
11. Nozzle and Holder 6162-15-3100
12. Open Pre:MPa(Kqf/cm2) 26.0{265}
13. NOZZLE-HOLDER 105041-7140
14. NOZZLE 105025-0870
15. NOZZLE SET

Include in #1:

106682-9401 as INJECTION-PUMP ASSEMBLY

Cross reference number

ZEXEL 106682-9401 1066829401


Zexel num
Bosch num
Firm num
Name
106682-9401 
 
   
INJECTION-PUMP ASSEMBLY
14CA PE6P,6PD PE

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil
  ISO4113 or {SAEJ967d}
Test oil temperature degC   40 40 45
Nozzle and nozzle holder   105780-8130
Bosch type code   EFEP215A
Nozzle   105780-0050
Bosch type code   DN6TD119NP1T
Nozzle holder   105780-2090
Bosch type code   EFEP215
Opening pressure MPa   17.2
Opening pressure kgf/cm2   175
Injection pipe
Outer diameter - inner diameter - length (mm)
mm   8-4-1000
Overflow valve   131425-1620
Overflow valve opening pressure kPa   255 221 289
Overflow valve opening pressure kgf/cm2   2.6 2.25 2.95
Tester oil delivery pressure kPa   157 157 157
Tester oil delivery pressure kgf/cm2   1.6 1.6 1.6
Direction of rotation (viewed from drive side)
Left
  L
Injection timing adjustment
Direction of rotation (viewed from drive side)
Left
  L
Injection order   1-5-3-6- 2-4
Pre-stroke mm   2.8 2.75 2.85
Beginning of injection position
Drive side
  NO.1
Difference between angles 1
Cal 1-5
deg.   60 59.5 60.5
Difference between angles 2
Cal 1-3
deg.   120 119.5 120.5
Difference between angles 3
Cal 1-6
deg.   180 179.5 180.5
Difference between angles 4
Cyl.1-2
deg.   240 239.5 240.5
Difference between angles 5
Cal 1-4
deg.   300 299.5 300.5
Injection quantity adjustment
Adjusting point   A
Rack position   14
Pump speed r/min   850 850 850
Average injection quantity mm3/st.   505 500 510
Max. variation between cylinders %   0 -3 3
Basic   *
Fixing the lever   *
Boost pressure kPa   60 60
Boost pressure mmHg   450 450
Injection quantity adjustment_02
Adjusting point   C
Rack position   6.8+-0.5
Pump speed r/min   365 365 365
Average injection quantity mm3/st.   12.5 7.5 17.5
Max. variation between cylinders %   0 -15 15
Fixing the rack   *
Boost pressure kPa   0 0 0
Boost pressure mmHg   0 0 0
Boost compensator adjustment
Pump speed r/min   600 600 600
Rack position   R1-3.4
Boost pressure kPa   6.7 4 9.4
Boost pressure mmHg   50 30 70
Boost compensator adjustment_02
Pump speed r/min   600 600 600
Rack position   R1(14.5)
Boost pressure kPa   46.7 40 53.4
Boost pressure mmHg   350 300 400

Test data Ex:

Governor adjustment

Test data 106682-9401
N:Pump speed R:Rack position (mm) (1)Target notch: K (2)Boost compensator stroke: BCL (3)Rack difference between N = N1 and N = N2
----------
K=20 BCL=3.4+-0.1mm N1=850r/min N2=650r/min
----------

Speed control lever angle

Test data 106682-9401
F:Full speed I:Idle S:Stop (1)Use the hole at R = aa
----------
aa=90mm
----------
a=18deg+-5deg b=24deg+-5deg c=52deg+-3deg

0000001501 LEVER

Test data 106682-9401
1. Adjustment of the control lever (1)Perform idling with the speed lever (a) contacting the pushrod (b) At this time, confirm that the spring (c) is not compressed by speed lever (a)'s operating torque. (2)To set the stop position, compress spring (c) using the speed lever (a) and adjust the rack so that it contacts the guide screw at position L1. Then, set and fix using the lock nut (e). Adjust rack position at this time using shim (f). (3)After pulling the speed lever (a) in the stop direction and releasing it, confirm that it returns to the idle position.
----------
L1=0.2~2mm
----------

Timing setting

Test data 106682-9401
(1)Pump vertical direction (2)Coupling's key groove position at No 1 cylinder's beginning of injection (3)- (4)-
----------

----------
a=(40deg)




Have questions with 106682-9401?





Group cross 106682-9401 ZEXEL

Komatsu 

 
6162752130 
INJECTION-PUMP ASSEMBLY
SA6D170
106682-9401  
 
 
INJECTION-PUMP ASSEMBLY
 
 
INJECTION-PUMP ASSEMBLY

Komatsu 

9 400 617 617 
6162752131 
INJECTION-PUMP ASSEMBLY
SA6D170
 
6162752220 
INJECTION-PUMP ASSEMBLY
SA6D170
 
 
INJECTION-PUMP ASSEMBLY
 
 
INJECTION-PUMP ASSEMBLY
 
 
INJECTION-PUMP ASSEMBLY

Komatsu 

9 400 611 343 
6162752221 
INJECTION-PUMP ASSEMBLY
SA6D170
 
6212721420 
INJECTION-PUMP ASSEMBLY
SAA6D140
 
 
INJECTION-PUMP ASSEMBLY
 
 
INJECTION-PUMP ASSEMBLY
9 400 611 539 
 
INJECTION-PUMP ASSEMBLY

Komatsu 

9 400 617 618 
6212721421 
INJECTION-PUMP ASSEMBLY
SAA6D140
9 400 612 129 
6162752230 
INJECTION-PUMP ASSEMBLY
S6D170
 
 
INJECTION-PUMP ASSEMBLY
 
 
INJECTION-PUMP ASSEMBLY
 
 
INJECTION-PUMP ASSEMBLY

Komatsu 

9 400 612 381 
6162752120 
INJECTION-PUMP ASSEMBLY
SA6D170
 
6152721970 
INJECTION-PUMP ASSEMBLY
SAA6D125
9 400 610 979 
6152721971 
INJECTION-PUMP ASSEMBLY
SAA6D125
F 019 Z10 203 
6152721980 
INJECTION-PUMP ASSEMBLY
SAA6D125
9 400 617 619 
6152721981 
INJECTION-PUMP ASSEMBLY
SAA6D125
 
 
INJECTION-PUMP ASSEMBLY

Komatsu 

9 400 611 668 
6215711850 
INJECTION-PUMP ASSEMBLY
SA12V140
 
 
INJECTION-PUMP ASSEMBLY
SA12V140
 
 
INJECTION-PUMP ASSEMBLY

Komatsu 

9 400 617 620 
6215711851 
INJECTION-PUMP ASSEMBLY
SA12V140
9 400 611 845 
6162751950 
INJECTION-PUMP ASSEMBLY
SA6D170
 
 
INJECTION-PUMP ASSEMBLY

Komatsu 

9 400 617 621 
6215711290 
INJECTION-PUMP ASSEMBLY
SA12V140
Back to top