106675-4452 ZEXEL 9 400 617 397 BOSCH INJECTION-PUMP ASSEMBLY 9400617397 1066754452


106675-4452 INJECTION-PUMP ASSEMBLY
Rating:
20
Buy INJECTION-PUMP ASSEMBLY 106675-4452 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

BOSCH 9 400 617 397 9400617397
ZEXEL 106675-4452 1066754452

Service parts 106675-4452 INJECTION-PUMP ASSEMBLY:

1. _
2. FUEL INJECTION PUMP 106067-1351
3. GOVERNOR 105407-6542
4. SUPPLY PUMP 105207-1700
5. AUTOM. ADVANCE MECHANIS
6. COUPLING PLATE 105663-0470
7. COUPLING PLATE
8. _
9. _
10. NOZZLE AND HOLDER ASSY
11. Nozzle and Holder
12. Open Pre:MPa(Kqf/cm2)
13. NOZZLE-HOLDER
14. NOZZLE
15. NOZZLE SET

Include in #1:

106675-4452 as INJECTION-PUMP ASSEMBLY

Cross reference number

BOSCH 9 400 617 397 9400617397
ZEXEL 106675-4452 1066754452


Zexel num
Bosch num
Firm num
Name
106675-4452 
9 400 617 397 
  DAEWOO
INJECTION-PUMP ASSEMBLY
D2366T K

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil
  ISO4113 or {SAEJ967d}
Test oil temperature degC   40 40 45
Nozzle and nozzle holder   105780-8140
Bosch type code   EF8511/9A
Nozzle   105780-0000
Bosch type code   DN12SD12T
Nozzle holder   105780-2080
Bosch type code   EF8511/9
Opening pressure MPa   17.2
Opening pressure kgf/cm2   175
Injection pipe
Outer diameter - inner diameter - length (mm)
mm   8-3-600
Overflow valve   131424-4420
Overflow valve opening pressure kPa   157 123 191
Overflow valve opening pressure kgf/cm2   1.6 1.25 1.95
Tester oil delivery pressure kPa   157 157 157
Tester oil delivery pressure kgf/cm2   1.6 1.6 1.6
Direction of rotation (viewed from drive side)
Right
  R
Injection timing adjustment
Direction of rotation (viewed from drive side)
Right
  R
Injection order   1-5-3-6- 2-4
Pre-stroke mm   4.3 4.25 4.35
Beginning of injection position
Governor side
  NO.1
Difference between angles 1
Cal 1-5
deg.   60 59.5 60.5
Difference between angles 2
Cal 1-3
deg.   120 119.5 120.5
Difference between angles 3
Cal 1-6
deg.   180 179.5 180.5
Difference between angles 4
Cyl.1-2
deg.   240 239.5 240.5
Difference between angles 5
Cal 1-4
deg.   300 299.5 300.5
Injection quantity adjustment
Adjusting point   A
Rack position   10.8
Pump speed r/min   1100 1100 1100
Average injection quantity mm3/st.   145 143 147
Max. variation between cylinders %   0 -2 2
Basic   *
Fixing the lever   *
Boost pressure kPa   80 80
Boost pressure mmHg   600 600
Injection quantity adjustment_02
Adjusting point   B
Rack position   4.9+-0.5
Pump speed r/min   400 400 400
Average injection quantity mm3/st.   15.5 14 17
Max. variation between cylinders %   0 -15 15
Fixing the rack   *
Boost pressure kPa   0 0 0
Boost pressure mmHg   0 0 0
Injection quantity adjustment_03
Adjusting point   E
Rack position   -
Pump speed r/min   100 100 100
Average injection quantity mm3/st.   146 146 156
Fixing the lever   *
Boost pressure kPa   0 0 0
Boost pressure mmHg   0 0 0
Rack limit   *
Boost compensator adjustment
Pump speed r/min   500 500 500
Rack position   R1-1.6
Boost pressure kPa   13.3 11.3 15.3
Boost pressure mmHg   100 85 115
Boost compensator adjustment_02
Pump speed r/min   500 500 500
Rack position   R1-1
Boost pressure kPa   32 28 36
Boost pressure mmHg   240 210 270
Boost compensator adjustment_03
Pump speed r/min   500 500 500
Rack position   R1(10.8)
Boost pressure kPa   66.7 66.7 66.7
Boost pressure mmHg   500 500 500

Test data Ex:

Governor adjustment

Test data 106675-4452
N:Pump speed R:Rack position (mm) (1)Target notch: K (2)Tolerance for racks not indicated: +-0.05mm. (3)Deliver without the torque control spring operating. (4)RACK LIMIT (5)Boost compensator stroke: BCL (6)Set idle sub-spring
----------
K=7 BCL=1.6+-0.1mm
----------

Speed control lever angle

Test data 106675-4452
F:Full speed I:Idle (1)Stopper bolt setting
----------

----------
a=10deg+-5deg b=27deg+-5deg

Stop lever angle

Test data 106675-4452
N:Pump normal S:Stop the pump. (1)Pump speed aa and rack position bb (to be sealed at delivery)
----------
aa=0r/min bb=1-0.5mm
----------
a=32deg+-5deg b=70deg+-5deg

0000001501 TAMPER PROOF

Test data 106675-4452
Tamperproofing-equipped boost compensator cover installation procedure (A) After adjusting the boost compensator, tighten the bolts to remove the heads. (1)Before adjusting the governor and the boost compensator, tighten the screw to the specified torque. (Tightening torque T = T1 maximum) (2)After adjusting the governor and the boost compensator, tighten to the specified torque to break off the bolt heads. (Tightening torque T = T2)
----------
T1=2.5N-m(0.25kgf-m) T2=2.9~4.4N-m(0.3~0.45kgf-m)
----------

Timing setting

Test data 106675-4452
(1)Pump vertical direction (2)Coupling's key groove position at No 1 cylinder's beginning of injection (3)- (4)-
----------

----------
a=(70deg)




Have questions with 106675-4452?





Group cross 106675-4452 ZEXEL

 
 
INJECTION-PUMP ASSEMBLY

Komatsu 

9 400 617 394 
6211721310 
INJECTION-PUMP ASSEMBLY
S6D140
 
6211711490 
INJECTION-PUMP ASSEMBLY
S6D140
 
6211711491 
INJECTION-PUMP ASSEMBLY
S6D140
 
 
INJECTION-PUMP ASSEMBLY
S6D140

Komatsu 

9 400 617 395 
6211711492 
INJECTION-PUMP ASSEMBLY
S6D140
F 01G 09U 1C6 
 
INJECTION-PUMP ASSEMBLY

Komatsu 

9 400 611 536 
6211721470 
INJECTION-PUMP ASSEMBLY
S6D140
 
6152721240 
INJECTION-PUMP ASSEMBLY
SA6D125
9 400 612 703 
6152721241 
INJECTION-PUMP ASSEMBLY
SA6D125
 
 
INJECTION-PUMP ASSEMBLY
F 019 Z20 141 
 
INJECTION-PUMP ASSEMBLY
S6D140

Komatsu 

9 400 617 396 
6211721320 
INJECTION-PUMP ASSEMBLY
S6D140

Daewoo 

 
 
INJECTION-PUMP ASSEMBLY
D2366T
 
 
INJECTION-PUMP ASSEMBLY
D2366T
106675-4452  
9 400 617 397 
 
INJECTION-PUMP ASSEMBLY
D2366T

Komatsu 

 
6211711750 
INJECTION-PUMP ASSEMBLY
S6D140
9 400 617 398 
6211711751 
INJECTION-PUMP ASSEMBLY
S6D140
9 400 619 775 
 
INJECTION-PUMP ASSEMBLY
SA6D125E

Komatsu 

9 400 617 399 
6152721410 
INJECTION-PUMP ASSEMBLY
SA6D125E
 
 
INJECTION-PUMP ASSEMBLY

Komatsu 

 
6152721150 
INJECTION-PUMP ASSEMBLY
SA6D125
9 400 617 400 
6152721151 
INJECTION-PUMP ASSEMBLY
SA6D125
 
 
INJECTION-PUMP ASSEMBLY
 
 
INJECTION-PUMP ASSEMBLY
 
 
INJECTION-PUMP ASSEMBLY
SA6D125
 
 
INJECTION-PUMP ASSEMBLY

Komatsu 

9 400 617 401 
6152712750 
INJECTION-PUMP ASSEMBLY
SA6D125
Back to top