106673-7160 ZEXEL 9 400 610 922 BOSCH INJECTION-PUMP ASSEMBLY 9400610922 1066737160 me158044


106673-7160 INJECTION-PUMP ASSEMBLY
Rating:
11
Buy INJECTION-PUMP ASSEMBLY 106673-7160 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

BOSCH 9 400 610 922 9400610922
ZEXEL 106673-7160 1066737160
MITSUBISHI ME158044 me158044

Service parts 106673-7160 INJECTION-PUMP ASSEMBLY:

1. _
2. FUEL INJECTION PUMP 106061-5030
3. GOVERNOR 105407-5710
4. SUPPLY PUMP 105207-1210
5. AUTOM. ADVANCE MECHANIS 105636-1880
6. COUPLING PLATE 105662-0710
7. COUPLING PLATE
8. _
9. _
10. NOZZLE AND HOLDER ASSY 105101-5990
11. Nozzle and Holder ME050883
12. Open Pre:MPa(Kqf/cm2) 21.6{220}
13. NOZZLE-HOLDER 105031-3970
14. NOZZLE 105015-6150
15. NOZZLE SET

Include in #1:

106673-7160 as INJECTION-PUMP ASSEMBLY

Cross reference number

BOSCH 9 400 610 922 9400610922
ZEXEL 106673-7160 1066737160
MITSUBISHI ME158044 me158044


Zexel num
Bosch num
Firm num
Name
106673-7160 
9 400 610 922 
ME158044  MITSUBISHI
INJECTION-PUMP ASSEMBLY
6D22TC K

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil
  ISO4113 or {SAEJ967d}
Test oil temperature degC   40 40 45
Nozzle and nozzle holder   105780-8140
Bosch type code   EF8511/9A
Nozzle   105780-0000
Bosch type code   DN12SD12T
Nozzle holder   105780-2080
Bosch type code   EF8511/9
Opening pressure MPa   17.2
Opening pressure kgf/cm2   175
Injection pipe
Outer diameter - inner diameter - length (mm)
mm   8-3-600
Overflow valve   131424-4620
Overflow valve opening pressure kPa   255 221 289
Overflow valve opening pressure kgf/cm2   2.6 2.25 2.95
Tester oil delivery pressure kPa   157 157 157
Tester oil delivery pressure kgf/cm2   1.6 1.6 1.6
Direction of rotation (viewed from drive side)
Right
  R
Injection timing adjustment
Direction of rotation (viewed from drive side)
Right
  R
Injection order   1-5-3-6- 2-4
Pre-stroke mm   4.8 4.75 4.85
Beginning of injection position
Governor side
  NO.1
Difference between angles 1
Cal 1-5
deg.   60 59.5 60.5
Difference between angles 2
Cal 1-3
deg.   120 119.5 120.5
Difference between angles 3
Cal 1-6
deg.   180 179.5 180.5
Difference between angles 4
Cyl.1-2
deg.   240 239.5 240.5
Difference between angles 5
Cal 1-4
deg.   300 299.5 300.5
Injection quantity adjustment
Adjusting point   A
Rack position   10.5
Pump speed r/min   800 800 800
Average injection quantity mm3/st.   145.3 142.3 148.3
Max. variation between cylinders %   0 -3 3
Basic   *
Fixing the lever   *
Boost pressure kPa   49.3 49.3
Boost pressure mmHg   370 370
Injection quantity adjustment_02
Adjusting point   B
Rack position   5.8+-0.5
Pump speed r/min   275 275 275
Average injection quantity mm3/st.   15 12.4 17.6
Fixing the rack   *
Boost pressure kPa   0 0 0
Boost pressure mmHg   0 0 0
Remarks
(check)
 
Injection quantity adjustment_03
Adjusting point   C
Rack position   5.2+-0.5
Pump speed r/min   500 500 500
Average injection quantity mm3/st.   15 12.4 17.6
Max. variation between cylinders %   0 -15 15
Fixing the rack   *
Boost pressure kPa   0 0 0
Boost pressure mmHg   0 0 0
Injection quantity adjustment_04
Adjusting point   D
Rack position   -
Pump speed r/min   100 100 100
Average injection quantity mm3/st.   142 122 162
Fixing the lever   *
Boost pressure kPa   0 0 0
Boost pressure mmHg   0 0 0
Rack limit   *
Boost compensator adjustment
Pump speed r/min   600 600 600
Rack position   R1-1.2
Boost pressure kPa   6.7 5.4 8
Boost pressure mmHg   50 40 60
Boost compensator adjustment_02
Pump speed r/min   600 600 600
Rack position   R1(10.5)
Boost pressure kPa   36 29.3 42.7
Boost pressure mmHg   270 220 320
Timer adjustment
Pump speed r/min   1050--
Advance angle deg.   0 0 0
Remarks
Start
 
Timer adjustment_02
Pump speed r/min   1000
Advance angle deg.   0.5
Timer adjustment_03
Pump speed r/min   1100
Advance angle deg.   1.5 1 2
Timer adjustment_04
Pump speed r/min   -
Advance angle deg.   2 2 2
Remarks
Measure the actual speed, stop
 

Test data Ex:

Governor adjustment

Test data 106673-7160
N:Pump speed R:Rack position (mm) (1)Target notch: K (2)Tolerance for racks not indicated: +-0.05mm. (3)RACK LIMIT (4)Main spring setting (5)Set idle sub-spring (6)Boost compensator stroke (7)Set at delivery (8)Rack difference between N = N1 and N = N2 (9)Damper spring setting: DL
----------
K=9 N1=800r/min N2=300r/min DL=5.8-0.2mm
----------

Speed control lever angle

Test data 106673-7160
F:Full speed I:Idle (1)Stopper bolt setting (2)At delivery (3)Set the pump speed at aa (4)Set the pump speed at bb.
----------
aa=1115r/min bb=915r/min
----------
a=29deg+-5deg b=(2deg) c=11deg+-5deg d=8deg+-5deg

Stop lever angle

Test data 106673-7160
N:Pump normal S:Stop the pump. (1)Pump speed aa and rack position bb (to be sealed at delivery) (2)Stopper bolt setting
----------
aa=0r/min bb=1-0.2mm
----------
a=50deg+-5deg b=70deg+-5deg

Timing setting

Test data 106673-7160
(1)Pump vertical direction (2)Coupling's key groove position at No 1 cylinder's beginning of injection (3)- (4)-
----------

----------
a=(10deg)




Have questions with 106673-7160?





Group cross 106673-7160 ZEXEL

Mitsubishi 

9 400 611 459 
ME158037 
INJECTION-PUMP ASSEMBLY
6D22T
9 400 617 325 
ME151383 
INJECTION-PUMP ASSEMBLY
6D22T3
 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

9 400 617 326 
ME151381 
INJECTION-PUMP ASSEMBLY
6D24T1
 
 
INJECTION-PUMP ASSEMBLY
 
 
INJECTION-PUMP ASSEMBLY
 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

9 400 617 327 
ME151380 
INJECTION-PUMP ASSEMBLY
6D24T1
9 400 617 328 
ME158068 
INJECTION-PUMP ASSEMBLY
6D24T
9 400 617 329 
ME151542 
INJECTION-PUMP ASSEMBLY
6D22T3
106673-7160  
9 400 610 922 
ME158044 
INJECTION-PUMP ASSEMBLY
6D22TC
9 400 617 330 
ME151466 
INJECTION-PUMP ASSEMBLY
6D22T6
 
 
INJECTION-PUMP ASSEMBLY
 
 
INJECTION-PUMP ASSEMBLY
 
 
INJECTION-PUMP ASSEMBLY
9 400 610 923 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

9 400 612 006 
ME158081 
INJECTION-PUMP ASSEMBLY
6D24T
 
 
INJECTION-PUMP ASSEMBLY
 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

9 400 611 460 
ME158086 
INJECTION-PUMP ASSEMBLY
6D24TC
Back to top