106673-2883 ZEXEL 9 400 610 911 BOSCH INJECTION-PUMP ASSEMBLY 9400610911 1066732883 me157870


106673-2883 INJECTION-PUMP ASSEMBLY
Rating:
11
Buy INJECTION-PUMP ASSEMBLY 106673-2883 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

BOSCH 9 400 610 911 9400610911
ZEXEL 106673-2883 1066732883
MITSUBISHI ME157870 me157870

Service parts 106673-2883 INJECTION-PUMP ASSEMBLY:

1. _
2. FUEL INJECTION PUMP 106067-0391
3. GOVERNOR 105407-5641
4. SUPPLY PUMP 105207-1210
5. AUTOM. ADVANCE MECHANIS 105636-1880
6. COUPLING PLATE 105662-0710
7. COUPLING PLATE
8. _
9. _
10. NOZZLE AND HOLDER ASSY 105100-7110
11. Nozzle and Holder ME056473
12. Open Pre:MPa(Kqf/cm2) 17.7{180}/21.6{220}
13. NOZZLE-HOLDER 105031-4530
14. NOZZLE 105015-6150
15. NOZZLE SET

Include in #1:

106673-2883 as INJECTION-PUMP ASSEMBLY

Cross reference number

BOSCH 9 400 610 911 9400610911
ZEXEL 106673-2883 1066732883
MITSUBISHI ME157870 me157870


Zexel num
Bosch num
Firm num
Name
106673-2883 
9 400 610 911 
ME157870  MITSUBISHI
INJECTION-PUMP ASSEMBLY
6D22TC * K 14CA INJECTION PUMP ASSY PE6P,6PD PE

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil
  ISO4113 or {SAEJ967d}
Test oil temperature degC   40 40 45
Nozzle and nozzle holder   105780-8140
Bosch type code   EF8511/9A
Nozzle   105780-0000
Bosch type code   DN12SD12T
Nozzle holder   105780-2080
Bosch type code   EF8511/9
Opening pressure MPa   17.2
Opening pressure kgf/cm2   175
Injection pipe
Outer diameter - inner diameter - length (mm)
mm   8-3-600
Overflow valve   131424-4620
Overflow valve opening pressure kPa   255 221 289
Overflow valve opening pressure kgf/cm2   2.6 2.25 2.95
Tester oil delivery pressure kPa   157 157 157
Tester oil delivery pressure kgf/cm2   1.6 1.6 1.6
Direction of rotation (viewed from drive side)
Right
  R
Injection timing adjustment
Direction of rotation (viewed from drive side)
Right
  R
Injection order   1-5-3-6- 2-4
Pre-stroke mm   4.8 4.75 4.85
Beginning of injection position
Governor side
  NO.1
Difference between angles 1
Cal 1-5
deg.   60 59.5 60.5
Difference between angles 2
Cal 1-3
deg.   120 119.5 120.5
Difference between angles 3
Cal 1-6
deg.   180 179.5 180.5
Difference between angles 4
Cyl.1-2
deg.   240 239.5 240.5
Difference between angles 5
Cal 1-4
deg.   300 299.5 300.5
Injection quantity adjustment
Adjusting point   A
Rack position   9.9
Pump speed r/min   1000 1000 1000
Average injection quantity mm3/st.   149.5 146.5 152.5
Max. variation between cylinders %   0 -3 3
Basic   *
Fixing the lever   *
Boost pressure kPa   85.3 85.3
Boost pressure mmHg   640 640
Injection quantity adjustment_02
Adjusting point   B
Rack position   5.2+-0.5
Pump speed r/min   425 425 425
Average injection quantity mm3/st.   21 18.4 23.6
Max. variation between cylinders %   0 -15 15
Fixing the rack   *
Boost pressure kPa   0 0 0
Boost pressure mmHg   0 0 0
Injection quantity adjustment_03
Adjusting point   E
Rack position   -
Pump speed r/min   100 100 100
Average injection quantity mm3/st.   165 145 185
Fixing the lever   *
Boost pressure kPa   0 0 0
Boost pressure mmHg   0 0 0
Rack limit   *
Boost compensator adjustment
Pump speed r/min   850 850 850
Rack position   R1-1.2
Boost pressure kPa   34.7 32 37.4
Boost pressure mmHg   260 240 280
Boost compensator adjustment_02
Pump speed r/min   850 850 850
Rack position   R1(9.9)
Boost pressure kPa   72 65.3 78.7
Boost pressure mmHg   540 490 590
Timer adjustment
Pump speed r/min   (N1+50)- -
Advance angle deg.   0 0 0
Remarks
Start
 
Timer adjustment_02
Pump speed r/min   N1
Advance angle deg.   0.5
Remarks
Measure the actual speed.
 
Timer adjustment_03
Pump speed r/min   1000
Remarks
Measure the actual advance angle.
 
Timer adjustment_04
Pump speed r/min   -
Advance angle deg.   2 2 2
Remarks
Measure the actual speed, stop
 

Test data Ex:

Governor adjustment

Test data 106673-2883
N:Pump speed R:Rack position (mm) (1)Target notch: K (2)Tolerance for racks not indicated: +-0.05mm. (3)RACK LIMIT (4)Main spring setting (5)Set idle sub-spring (6)Boost compensator stroke (7)Rack difference between N = N1 and N = N2 (8)Rack difference between N = N3 and N = N4
----------
K=12 N1=1000r/min N2=700r/min N3=1000r/min N4=300r/min
----------

Speed control lever angle

Test data 106673-2883
F:Full speed I:Idle (1)Stopper bolt setting
----------

----------
a=28deg+-5deg b=8deg+-5deg

Stop lever angle

Test data 106673-2883
N:Pump normal S:Stop the pump. (1)Pump speed aa and rack position bb (to be sealed at delivery) (2)Stopper bolt setting
----------
aa=0r/min bb=1-0.5mm
----------
a=35deg+-5deg b=70deg+-5deg

Timing setting

Test data 106673-2883
(1)Pump vertical direction (2)Coupling's key groove position at No 1 cylinder's beginning of injection (3)- (4)-
----------

----------
a=(7deg)




Have questions with 106673-2883?





Group cross 106673-2883 ZEXEL

F 019 Z10 418 
 
INJECTION-PUMP ASSEMBLY
F 019 Z10 419 
 
INJECTION-PUMP ASSEMBLY
F 019 Z10 420 
 
INJECTION-PUMP ASSEMBLY
F 019 Z10 421 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

9 400 617 267 
ME150598 
INJECTION-PUMP ASSEMBLY
6D22T3
9 400 617 268 
ME150602 
INJECTION-PUMP ASSEMBLY
6D22T3
F 019 Z10 422 
 
INJECTION-PUMP ASSEMBLY
F 019 Z10 019 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

9 400 617 269 
ME150593 
INJECTION-PUMP ASSEMBLY
E81XT1
F 019 Z10 020 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

9 400 617 270 
ME150594 
INJECTION-PUMP ASSEMBLY
E81XT2
9 400 617 271 
ME150724 
INJECTION-PUMP ASSEMBLY
6D22T
9 400 617 272 
ME150668 
INJECTION-PUMP ASSEMBLY
6D22T2
9 400 617 273 
ME150684 
INJECTION-PUMP ASSEMBLY
6D22T2
 
 
INJECTION-PUMP ASSEMBLY
 
 
INJECTION-PUMP ASSEMBLY
 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

9 400 610 910 
ME157869 
INJECTION-PUMP ASSEMBLY
6D22T
F 01G 09U 08L 
 
INJECTION-PUMP ASSEMBLY
F 01G 09U 08M 
 
INJECTION-PUMP ASSEMBLY
F 01G 09U 08N 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

106673-2883  
9 400 610 911 
ME157870 
INJECTION-PUMP ASSEMBLY
6D22TC
F 01G 09U 08P 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

9 400 617 274 
ME150753 
INJECTION-PUMP ASSEMBLY
6D22T2
Back to top