106673-2280 ZEXEL 9 400 617 225 BOSCH INJECTION-PUMP ASSEMBLY 9400617225 1066732280 me056821


106673-2280 INJECTION-PUMP ASSEMBLY
Rating:
20
Buy INJECTION-PUMP ASSEMBLY 106673-2280 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

BOSCH 9 400 617 225 9400617225
ZEXEL 106673-2280 1066732280
MITSUBISHI ME056821 me056821

Service parts 106673-2280 INJECTION-PUMP ASSEMBLY:

1. _
2. FUEL INJECTION PUMP 106061-5040
3. GOVERNOR 105487-4660
4. SUPPLY PUMP 105207-1330
5. AUTOM. ADVANCE MECHANIS 105636-0920
6. COUPLING PLATE 105662-0710
7. COUPLING PLATE
8. _
9. _
10. NOZZLE AND HOLDER ASSY 105100-5820
11. Nozzle and Holder ME056329
12. Open Pre:MPa(Kqf/cm2) 17.7{180}/21.6{220}
13. NOZZLE-HOLDER 105031-4530
14. NOZZLE 105015-5390
15. NOZZLE SET

Include in #1:

106673-2280 as INJECTION-PUMP ASSEMBLY

Cross reference number

BOSCH 9 400 617 225 9400617225
ZEXEL 106673-2280 1066732280
MITSUBISHI ME056821 me056821


Zexel num
Bosch num
Firm num
Name
106673-2280 
106673-2250 
9 400 617 225 
ME056821  MITSUBISHI
INJECTION-PUMP ASSEMBLY
6D22 K 14CA INJECTION PUMP ASSY PE6P,6PD PE

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil
  ISO4113 or {SAEJ967d}
Test oil temperature degC   40 40 45
Nozzle and nozzle holder   105780-8140
Bosch type code   EF8511/9A
Nozzle   105780-0000
Bosch type code   DN12SD12T
Nozzle holder   105780-2080
Bosch type code   EF8511/9
Opening pressure MPa   17.2
Opening pressure kgf/cm2   175
Injection pipe
Outer diameter - inner diameter - length (mm)
mm   8-3-600
Overflow valve   131424-4620
Overflow valve opening pressure kPa   255 221 289
Overflow valve opening pressure kgf/cm2   2.6 2.25 2.95
Tester oil delivery pressure kPa   157 157 157
Tester oil delivery pressure kgf/cm2   1.6 1.6 1.6
Direction of rotation (viewed from drive side)
Right
  R
Injection timing adjustment
Direction of rotation (viewed from drive side)
Right
  R
Injection order   1-5-3-6- 2-4
Pre-stroke mm   4.8 4.75 4.85
Beginning of injection position
Governor side
  NO.1
Difference between angles 1
Cal 1-5
deg.   60 59.5 60.5
Difference between angles 2
Cal 1-3
deg.   120 119.5 120.5
Difference between angles 3
Cal 1-6
deg.   180 179.5 180.5
Difference between angles 4
Cyl.1-2
deg.   240 239.5 240.5
Difference between angles 5
Cal 1-4
deg.   300 299.5 300.5
Injection quantity adjustment
Adjusting point   -
Rack position   8.1
Pump speed r/min   700 700 700
Each cylinder's injection qty mm3/st.   109 106.3 111.7
Basic   *
Fixing the rack   *
Standard for adjustment of the maximum variation between cylinders   *
Injection quantity adjustment_02
Adjusting point   F
Rack position   5+-0.5
Pump speed r/min   500 500 500
Each cylinder's injection qty mm3/st.   16.5 14 19
Fixing the rack   *
Standard for adjustment of the maximum variation between cylinders   *
Injection quantity adjustment_03
Adjusting point   A
Rack position   R1(8.1)
Pump speed r/min   700 700 700
Average injection quantity mm3/st.   109 108 110
Basic   *
Fixing the lever   *
Injection quantity adjustment_04
Adjusting point   B
Rack position   R1(8.1)
Pump speed r/min   1100 1100 1100
Average injection quantity mm3/st.   123 119 127
Difference in delivery mm3/st.   8 8 8
Fixing the lever   *
Injection quantity adjustment_05
Adjusting point   C
Rack position   5.7+-0.5
Pump speed r/min   225 225 225
Each cylinder's injection qty mm3/st.   16.5 14 19
Fixing the rack   *
Remarks
(check)
 
Injection quantity adjustment_06
Adjusting point   E
Rack position   -
Pump speed r/min   100 100 100
Average injection quantity mm3/st.   150 110 190
Fixing the lever   *
Remarks
After startup boost setting
 
Timer adjustment
Pump speed r/min   950
Advance angle deg.   0.5
Timer adjustment_02
Pump speed r/min   1050
Advance angle deg.   2.2 1.7 2.7
Timer adjustment_03
Pump speed r/min   1150
Advance angle deg.   5.5 5 6
Remarks
Finish
 

Test data Ex:

Governor adjustment

Test data 106673-2280
N:Pump speed R:Rack position (mm) (1)Lever ratio: RT (2)Target shim dimension: TH (3)Excess fuel setting for starting: SXL (4)Damper spring setting: DL
----------
RT=1 TH=2.1mm SXL=R1+1+0.8mm DL=4.5-0.2mm
----------

Speed control lever angle

Test data 106673-2280
F:Full speed
----------

----------
a=27deg+-5deg

0000000901

Test data 106673-2280
F:Full load I:Idle (1)Stopper bolt setting
----------

----------
a=21.5deg+-3deg b=24deg+-5deg

Stop lever angle

Test data 106673-2280
N:Pump normal S:Stop the pump. (1)Rack position = aa (2)Rack position = bb, set the stopper bolt. (3)Free (at shipping)
----------
aa=16.6mm bb=4.1-0.5mm
----------
a=35deg+-5deg b=61.5deg+7deg-5deg c=(6deg)

0000001501 MICRO SWITCH

Adjustment of the micro-switch Adjust the bolt to obtain the following lever position when the micro-switch is ON. (1)Speed N1 (2)Rack position Ra
----------
N1=325+-5r/min Ra=5.4mm
----------

0000001601 LEVER

Test data 106673-2280
(1)Viewed from top of pump. (2)Pump side (3)Load control lever (4)Adjusting bolt (5)Nut 1. Idle increase link mechanism adjustment (1)After completing pump and governor adjustment, fix the load control lever in the idle position. (2)Adjust using the bolt (4) so that the idle-increase link mechanism's lever angle is a, then fix using the nut (5).
----------

----------
a=8.5deg+-3deg

Timing setting

Test data 106673-2280
(1)Pump vertical direction (2)Coupling's key groove position at No 1 cylinder's beginning of injection (3)- (4)-
----------

----------
a=(7deg)




Have questions with 106673-2280?





Group cross 106673-2280 ZEXEL

Mitsubishi 

9 400 617 220 
ME056840 
INJECTION-PUMP ASSEMBLY
6D22T2
 
 
INJECTION-PUMP ASSEMBLY
 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

9 400 617 221 
ME120515 
INJECTION-PUMP ASSEMBLY
6D40T1
9 400 617 222 
ME056812 
INJECTION-PUMP ASSEMBLY
6D22
9 400 617 223 
ME056819 
INJECTION-PUMP ASSEMBLY
6D22
F 01G 09U 08G 
ME056847 
INJECTION-PUMP ASSEMBLY
6D22
9 400 617 224 
ME056848 
INJECTION-PUMP ASSEMBLY
6D22
F 01G 09U 08H 
ME056849 
INJECTION-PUMP ASSEMBLY
6D22
F 01G 09U 08J 
ME056820 
INJECTION-PUMP ASSEMBLY
6D22
106673-2280  

106673-2250 
9 400 617 225 
ME056821 
INJECTION-PUMP ASSEMBLY
6D22
9 400 617 226 
ME157217 
INJECTION-PUMP ASSEMBLY
6D22TC
Back to top