106672-3900 ZEXEL F 019 Z10 127 BOSCH INJECTION-PUMP ASSEMBLY f019z10127 1066723900 220801860a


106672-3900 INJECTION-PUMP ASSEMBLY
Rating:
36
Buy INJECTION-PUMP ASSEMBLY 106672-3900 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

BOSCH F 019 Z10 127 f019z10127
ZEXEL 106672-3900 1066723900
HINO 220801860A 220801860a

Service parts 106672-3900 INJECTION-PUMP ASSEMBLY:

1. _
2. FUEL INJECTION PUMP 106067-6780
3. GOVERNOR 105952-2850
4. SUPPLY PUMP 105237-5040
5. AUTOM. ADVANCE MECHANIS
6. COUPLING PLATE 105663-0620
7. COUPLING PLATE 156643-7020
8. _
9. _
10. NOZZLE AND HOLDER ASSY 105101-7366
11. Nozzle and Holder
12. Open Pre:MPa(Kqf/cm2) 16.7{170}/23.5(240)
13. NOZZLE-HOLDER 105030-3482
14. NOZZLE
15. NOZZLE SET 105019-0161

Include in #1:

106672-3900 as INJECTION-PUMP ASSEMBLY

Cross reference number

BOSCH F 019 Z10 127 f019z10127
ZEXEL 106672-3900 1066723900
HINO 220801860A 220801860a


Zexel num
Bosch num
Firm num
Name
106672-3900 
F 019 Z10 127 
220801860A  HINO
INJECTION-PUMP ASSEMBLY
K13C-TI K 14CA INJECTION PUMP ASSY PE6P,6PD PE

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil
  ISO4113 or {SAEJ967d}
Test oil temperature degC   40 40 45
Nozzle and nozzle holder   105780-8140
Bosch type code   EF8511/9A
Nozzle   105780-0000
Bosch type code   DN12SD12T
Nozzle holder   105780-2080
Bosch type code   EF8511/9
Opening pressure MPa   17.2
Opening pressure kgf/cm2   175
Injection pipe
Outer diameter - inner diameter - length (mm)
mm   8-3-600
Overflow valve   134424-4420
Overflow valve opening pressure kPa   162 147 177
Overflow valve opening pressure kgf/cm2   1.65 1.5 1.8
Tester oil delivery pressure kPa   157 157 157
Tester oil delivery pressure kgf/cm2   1.6 1.6 1.6
RED3 control unit part number   407910-3 960
RED3 rack sensor specifications mm   19
Direction of rotation (viewed from drive side)
Left
  L
Injection timing adjustment
Direction of rotation (viewed from drive side)
Left
  L
Injection order   1-4-2-6- 3-5
Pre-stroke mm   4.4 4.34 4.4
Beginning of injection position
Drive side
  NO.1
Difference between angles 1
Cal 1-4
deg.   60 59.75 60.25
Difference between angles 2
Cyl.1-2
deg.   120 119.75 120.25
Difference between angles 3
Cal 1-6
deg.   180 179.75 180.25
Difference between angles 4
Cal 1-3
deg.   240 239.75 240.25
Difference between angles 5
Cal 1-5
deg.   300 299.75 300.25
Injection quantity adjustment
Rack position   (11)
Vist V   2.2 2.2 2.2
Pump speed r/min   900 900 900
Average injection quantity mm3/st.   143.5 141.5 145.5
Max. variation between cylinders %   0 -2 2
Basic   *
Injection quantity adjustment_02
Rack position   (6.9)
Vist V   2.82 2.72 2.92
Pump speed r/min   360 360 360
Average injection quantity mm3/st.   11.1 8.1 14.1
Max. variation between cylinders %   0 -15 15

Test data Ex:

Speed control lever angle

Test data 106672-3900
N:Pump normal S:Stop the pump. (1)Rack position = aa (2)Rack position bb
----------
aa=20mm bb=1mm
----------
a=27deg+-5deg b=37deg+-5deg

0000000901

Test data 106672-3900
(1)Pump vertical direction (2)Coupling's key groove position at No 1 cylinder's beginning of injection (3)- (4)-
----------

----------
a=(0deg)

Stop lever angle

Test data 106672-3900
(Rs) rack sensor specifications (C/U) control unit part number (V) Rack sensor output voltage (R) Rack position (mm) 1. Confirming governor output characteristics (rack 19 mm, span 6 mm) (1)When the output voltages of the rack sensor are V1 and V2, check that the rack positions R1 and R2 in the table above are satisfied.
----------

----------




Have questions with 106672-3900?





Group cross 106672-3900 ZEXEL

Hino 

106672-3900  
F 019 Z10 127 
220801860A 
INJECTION-PUMP ASSEMBLY
K13C-TI
F 019 Z20 114 
220801880A 
INJECTION-PUMP ASSEMBLY
K13C-TI
Back to top