106671-8292 ZEXEL INJECTION-PUMP ASSEMBLY Calibration Data 1066718292 220006552a

Information Cross number Calibration Data Calibration Data Ex

Price: query
Buy now
Add to cart Go to cart

Rating:

Buy INJECTION-PUMP ASSEMBLY 106671-8292 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

ZEXEL 106671-8292 1066718292

HINO 220006552A 220006552a

Cross reference number

ZEXEL 106671-8292 1066718292

HINO 220006552A 220006552a

Zexel num

Bosch num

Firm num

Name

106671-8292
106671-8294

220006552A HINO

INJECTION-PUMP ASSEMBLY
K13D *

Calibration Data:

Adjustment conditions

Test oil
1404 Test oil ISO4113 or {SAEJ967d}

Test oil temperature degC 40 40 45

Nozzle and nozzle holder 105780-8140

Bosch type code EF8511/9A

Nozzle 105780-0000

Bosch type code DN12SD12T

Nozzle holder 105780-2080

Bosch type code EF8511/9

Opening pressure MPa 17.2

Opening pressure kgf/cm2 175

Injection pipe
Outer diameter - inner diameter - length (mm) mm 8-3-600

Overflow valve 134424-1420

Overflow valve opening pressure kPa 162 147 177

Overflow valve opening pressure kgf/cm2 1.65 1.5 1.8

Tester oil delivery pressure kPa 157 157 157

Tester oil delivery pressure kgf/cm2 1.6 1.6 1.6

Direction of rotation (viewed from drive side)
Left L

Injection timing adjustment

Direction of rotation (viewed from drive side)
Left L

Injection order 1-4-2-6- 3-5

Pre-stroke mm 4.6 4.54 4.6

Beginning of injection position
Drive side NO.1

Difference between angles 1
Cal 1-4 deg. 60 59.75 60.25

Difference between angles 2
Cyl.1-2 deg. 120 119.75 120.25

Difference between angles 3
Cal 1-6 deg. 180 179.75 180.25

Difference between angles 4
Cal 1-3 deg. 240 239.75 240.25

Difference between angles 5
Cal 1-5 deg. 300 299.75 300.25

Injection quantity adjustment

Adjusting point A

Rack position 7.2

Pump speed r/min 500 500 500

Average injection quantity mm3/st. 141.4 138.4 144.4

Fixing the lever *

Injection quantity adjustment_02

Adjusting point B

Rack position 7.5

Pump speed r/min 700 700 700

Average injection quantity mm3/st. 149.7 147.7 151.7

Max. variation between cylinders % 0 -2 2

Basic *

Fixing the lever *

Injection quantity adjustment_03

Adjusting point C

Rack position 7.7

Pump speed r/min 1075 1075 1075

Average injection quantity mm3/st. 155.8 152.8 158.8

Fixing the lever *

Injection quantity adjustment_04

Adjusting point D

Rack position 3.7+-0.5

Pump speed r/min 225 225 225

Average injection quantity mm3/st. 8.8 5.8 11.8

Max. variation between cylinders % 0 -15 15

Fixing the rack *

Injection quantity adjustment_05

Adjusting point F

Rack position -

Pump speed r/min 100 100 100

Average injection quantity mm3/st. 160 160 180

Fixing the lever *

Remarks
After startup boost setting

Timer adjustment

Pump speed r/min 695--

Advance angle deg. 0 0 0

Load 1/4

Remarks
Start

Timer adjustment_02

Pump speed r/min 645

Advance angle deg. 0.3

Load 1/4

Timer adjustment_03

Pump speed r/min 800

Advance angle deg. 1 0.7 1.3

Load 4/4

Timer adjustment_04

Pump speed r/min 860

Advance angle deg. 1 0.7 1.3

Load 3/4

Timer adjustment_05

Pump speed r/min 1075

Advance angle deg. 5.5 5.2 5.8

Load 4/4

Remarks
Finish

Test data Ex:

Governor adjustment

N:Pump speed R:Rack position (mm) (1)Lever ratio: RT (2)Target shim dimension: TH (3)Tolerance for racks not indicated: +-0.05mm. (4)Excess fuel setting for starting: SXL (N = N1) (5)Damper spring setting (6)Set idle at point K (N = N2, R = R1) and confirm that the injection quantity at N = N3 at point J is Q1.
----------
RT=0.8 TH=2.8mm SXL=8+-0.1mm N1=350r/min N2=325r/min R1=3.7mm N3=1000r/min Q1=0mm3/st
----------

Speed control lever angle

F:Full speed
----------

----------
a=(12deg)+-5deg

0000000901

F:Full load I:Idle (1)Use the hole at R = aa (2)Stopper bolt setting
----------
aa=50mm
----------
a=16deg+-5deg b=36deg+-3deg

Stop lever angle

N:Pump normal S:Stop the pump.
----------

----------
a=15deg+-5deg b=64deg+-5deg

0000001501 RACK SENSOR

(VR) measurement voltage (I) Part number of the control unit (G) Apply red paint. (H): End surface of the pump 1. Rack sensor adjustment (-0620) (1)Fix the speed control lever at the full position (2)Set the speed to N1 r/min. (If the boost compensator is provided, apply boost pressure.) (3)Adjust the bobbin (A) so that the rack sensor's output voltage is VR+-0.01. (4)At that time, rack position must be Ra. (5)Apply G at two places. Connecting part between the joint (B) and the nut (F) Connecting part between the joint (B) and the end surface of the pump (H)
----------
N1=900r/min Ra=7.7mm
----------