106671-6580 ZEXEL 9 400 612 274 BOSCH INJECTION-PUMP ASSEMBLY 9400612274 1066716580 1156034290


106671-6580 INJECTION-PUMP ASSEMBLY
Rating:
36
Buy INJECTION-PUMP ASSEMBLY 106671-6580 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

BOSCH 9 400 612 274 9400612274
ZEXEL 106671-6580 1066716580
ISUZU 1156034290 1156034290

Service parts 106671-6580 INJECTION-PUMP ASSEMBLY:

1. _
2. FUEL INJECTION PUMP 106067-6300
3. GOVERNOR 105407-7970
4. SUPPLY PUMP 105237-4420
5. AUTOM. ADVANCE MECHANIS 105681-6000
6. COUPLING PLATE 105664-2011
7. COUPLING PLATE
8. _
9. _
10. NOZZLE AND HOLDER ASSY 105110-8191
11. Nozzle and Holder 1-15300-414-0
12. Open Pre:MPa(Kqf/cm2) 18.1{185}/22.1{225}
13. NOZZLE-HOLDER 105041-2082
14. NOZZLE
15. NOZZLE SET 105019-2720

Include in #1:

106671-6580 as INJECTION-PUMP ASSEMBLY

Cross reference number

BOSCH 9 400 612 274 9400612274
ZEXEL 106671-6580 1066716580
ISUZU 1156034290 1156034290


Zexel num
Bosch num
Firm num
Name
106671-6580 
106671-6581 
9 400 612 274 
1156034290  ISUZU
INJECTION-PUMP ASSEMBLY
6HK1-T * K 14CA PE6P,6PD PE

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil
  ISO4113 or {SAEJ967d}
Test oil temperature degC   40 40 45
Nozzle and nozzle holder   105780-8140
Bosch type code   EF8511/9A
Nozzle   105780-0000
Bosch type code   DN12SD12T
Nozzle holder   105780-2080
Bosch type code   EF8511/9
Opening pressure MPa   17.2
Opening pressure kgf/cm2   175
Injection pipe
Outer diameter - inner diameter - length (mm)
mm   8-3-600
Overflow valve   134424-4320
Overflow valve opening pressure kPa   255 221 289
Overflow valve opening pressure kgf/cm2   2.6 2.25 2.95
Tester oil delivery pressure kPa   255 255 255
Tester oil delivery pressure kgf/cm2   2.6 2.6 2.6
Direction of rotation (viewed from drive side)
Left
  L
Injection timing adjustment
Direction of rotation (viewed from drive side)
Left
  L
Injection order   1-5-3-6- 2-4
Pre-stroke mm   3.6 3.57 3.63
Beginning of injection position
Governor side
  NO.1
Difference between angles 1
Cal 1-5
deg.   60 59.75 60.25
Difference between angles 2
Cal 1-3
deg.   120 119.75 120.25
Difference between angles 3
Cal 1-6
deg.   180 179.75 180.25
Difference between angles 4
Cyl.1-2
deg.   240 239.75 240.25
Difference between angles 5
Cal 1-4
deg.   300 299.75 300.25
Injection quantity adjustment
Adjusting point   A
Rack position   11
Pump speed r/min   1100 1100 1100
Average injection quantity mm3/st.   110 109 111
Max. variation between cylinders %   0 -3 3
Basic   *
Fixing the lever   *
Boost pressure kPa   133 133
Boost pressure mmHg   1000 1000
Injection quantity adjustment_02
Adjusting point   -
Rack position   7.6+-0.5
Pump speed r/min   425 425 425
Average injection quantity mm3/st.   13.5 10.3 16.7
Max. variation between cylinders %   0 -15 15
Fixing the rack   *
Boost pressure kPa   0 0 0
Boost pressure mmHg   0 0 0
Remarks
Adjust only variation between cylinders; adjust governor according to governor specifications.
 
Injection quantity adjustment_03
Adjusting point   E
Rack position   11.2++
Pump speed r/min   100 100 100
Average injection quantity mm3/st.   130 120 140
Fixing the lever   *
Boost pressure kPa   0 0 0
Boost pressure mmHg   0 0 0
Rack limit   *
Boost compensator adjustment
Pump speed r/min   500 500 500
Rack position   R1-1.9
Boost pressure kPa   20 16 24
Boost pressure mmHg   150 120 180
Boost compensator adjustment_02
Pump speed r/min   500 500 500
Rack position   R1(11)
Boost pressure kPa   120 120 120
Boost pressure mmHg   900 900 900
Timer adjustment
Pump speed r/min   1200++
Advance angle deg.   0 0 0
Remarks
Do not advance until starting N = 1200.
 
Timer adjustment_02
Pump speed r/min   -
Advance angle deg.   0.7 0.7 0.7
Remarks
Measure the actual speed, stop
 

Test data Ex:

Governor adjustment

Test data 106671-6580
N:Pump speed R:Rack position (mm) (1)Target notch: K (2)Tolerance for racks not indicated: +-0.05mm. (3)Deliver with positive torque control spring not operating (4)RACK LIMIT (5)Boost compensator stroke: BCL
----------
K=13 BCL=1.9+-0.1mm
----------

Speed control lever angle

Test data 106671-6580
F:Full speed I:Idle S:Stop (1)Use the hole at R = aa
----------
aa=70mm
----------
a=10deg+-5deg b=23deg+-5deg c=31deg+-3deg

Stop lever angle

Test data 106671-6580
N:Pump normal S:Stop the pump. (1)Normal (2)Use the hole at R = aa (3)Rack position bb, pump speed cc (seal at delivery)
----------
aa=23mm bb=1-0.5mm cc=0r/min
----------
a=15deg+-5deg b=70deg+-5deg

0000001501 TAMPER PROOF

Test data 106671-6580
Tamperproofing-equipped boost compensator cover installation procedure (A) After adjusting the boost compensator, tighten the bolts to remove the heads. (1)Before adjusting the governor and the boost compensator, tighten the screw to the specified torque. (Tightening torque T = T1 maximum) (2)After adjusting the governor and the boost compensator, tighten to the specified torque to break off the bolt heads. (Tightening torque T = T2)
----------
T1=2.5N-m(0.25kgf-m) T2=2.9~4.4N-m(0.3~0.45kgf-m)
----------

Timing setting

Test data 106671-6580
(1)Pump vertical direction (2)Position of timer's threaded installation hole at No 1 cylinder's beginning of injection (3)B.T.D.C.: aa (4)-
----------
aa=7deg
----------
a=(50deg)




Have questions with 106671-6580?





Group cross 106671-6580 ZEXEL

Isuzu 

9 400 612 040 
1156033890 
INJECTION-PUMP ASSEMBLY
6HK1-T
9 400 612 041 
1156033940 
INJECTION-PUMP ASSEMBLY
6HK1-T
9 400 612 273 
 
INJECTION-PUMP ASSEMBLY

Isuzu 

9 400 616 911 
1156033570 
INJECTION-PUMP ASSEMBLY
6HK1-XQB
9 400 616 912 
1156033590 
INJECTION-PUMP ASSEMBLY
6SD1-TCE
9 400 616 913 
1156034080 
INJECTION-PUMP ASSEMBLY
6SD1-TCE
9 400 612 222 
1156034170 
INJECTION-PUMP ASSEMBLY
6HK1-T
9 400 612 307 
1156034171 
INJECTION-PUMP ASSEMBLY
6HK1-T
9 400 613 010 
1156034172 
INJECTION-PUMP ASSEMBLY
6HK1-T
9 400 612 223 
1156034180 
INJECTION-PUMP ASSEMBLY
6HK1-T
 
1156034260 
INJECTION-PUMP ASSEMBLY
6WG1-T
9 400 612 426 
1156034261 
INJECTION-PUMP ASSEMBLY
6WG1-T
106671-6580  

106671-6581 
9 400 612 274 
1156034290 
INJECTION-PUMP ASSEMBLY
6HK1-T
9 400 616 914 
1156034291 
INJECTION-PUMP ASSEMBLY
6HK1-T
9 400 612 464 
1156034300 
INJECTION-PUMP ASSEMBLY
6HE1-TMC
Back to top