106671-3570 ZEXEL INJECTION-PUMP ASSEMBLY Calibration Data 1066713570 220201860a

Information Cross number Calibration Data Calibration Data Ex

Price: query
Buy now
Add to cart Go to cart

Rating:

Buy INJECTION-PUMP ASSEMBLY 106671-3570 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

ZEXEL 106671-3570 1066713570

HINO 220201860A 220201860a

Cross reference number

ZEXEL 106671-3570 1066713570

HINO 220201860A 220201860a

Zexel num

Bosch num

Firm num

Name

106671-3570
106671-3571

220201860A HINO

INJECTION-PUMP ASSEMBLY
EP100 *

Calibration Data:

Adjustment conditions

Test oil
1404 Test oil ISO4113 or {SAEJ967d}

Test oil temperature degC 40 40 45

Nozzle and nozzle holder 105780-8140

Bosch type code EF8511/9A

Nozzle 105780-0000

Bosch type code DN12SD12T

Nozzle holder 105780-2080

Bosch type code EF8511/9

Opening pressure MPa 17.2

Opening pressure kgf/cm2 175

Injection pipe
Outer diameter - inner diameter - length (mm) mm 8-3-600

Overflow valve (drive side) 134424-1420

Overflow valve opening pressure (drive side) kPa 162 147 177

Overflow valve opening pressure (drive side) kgf/cm2 1.65 1.5 1.8

Overflow valve (governor side) 134424-1720

Overflow valve opening pressure (governor side) kPa 162 147 177

Overflow valve opening pressure (governor side) kgf/cm2 1.65 1.5 1.8

Tester oil delivery pressure kPa 157 157 157

Tester oil delivery pressure kgf/cm2 1.6 1.6 1.6

Direction of rotation (viewed from drive side)
Right R

Injection timing adjustment

Direction of rotation (viewed from drive side)
Right R

Injection order 1-4-2-6- 3-5

Pre-stroke mm 4.5 4.4 4.5

Beginning of injection position
Drive side NO.1

Difference between angles 1
Cal 1-4 deg. 60 59.5 60.5

Difference between angles 2
Cyl.1-2 deg. 120 119.5 120.5

Difference between angles 3
Cal 1-6 deg. 180 179.5 180.5

Difference between angles 4
Cal 1-3 deg. 240 239.5 240.5

Difference between angles 5
Cal 1-5 deg. 300 299.5 300.5

Injection quantity adjustment

Adjusting point A

Rack position 7.5

Pump speed r/min 800 800 800

Average injection quantity mm3/st. 101 99 103

Max. variation between cylinders % 0 -2 2

Basic *

Fixing the lever *

Injection quantity adjustment_02

Adjusting point B

Rack position 5.3+-0.5

Pump speed r/min 360 360 360

Average injection quantity mm3/st. 10 7 13

Max. variation between cylinders % 0 -15 15

Fixing the rack *

Injection quantity adjustment_03

Adjusting point C

Rack position 10.5

Pump speed r/min 100 100 100

Average injection quantity mm3/st. 140 130 150

Fixing the lever *

Rack limit *

Timer adjustment

Pump speed r/min (925)

Advance angle deg. 0.3

Timer adjustment_02

Pump speed r/min 1000

Advance angle deg. 0.8 0.3 1.3

Timer adjustment_03

Pump speed r/min -

Advance angle deg. 2.5 2.2 2.8

Remarks
Measure the actual speed, stop

Test data Ex:

Governor adjustment

N:Pump speed R:Rack position (mm) (1)Target notch: K (2)RACK LIMIT: RAL
----------
K=10 RAL=10.5+-0.1mm
----------

Speed control lever angle

F:Full speed I:Idle
----------

----------
a=8deg+-5deg b=17deg+-5deg

Stop lever angle

N:Pump normal S:Stop the pump.
----------

----------
a=27deg+-5deg b=53deg+-5deg

0000001501 LEVER

(F) P/N: Part number of the shim L1:Thickness (mm) 1. Adjustment of the control lever (1)Perform idling with the control lever (A) contacting the pushrod (B). At this time, confirm that the spring (C) is not compressed by control lever (A)'s operating torque. (2)To set the stop position, compress spring (C) using the control lever (A) and adjust the rack so that it contacts the guide screw (D) at position L2. Then, set and fix using the lock nut (E). Adjust the rack position L2 at this time using the shim (F). (3)Confirm that the control lever (A) returns to the idling position when pulled in the stop direction and then released.
----------
L2=0.2~2mm
----------