106671-1701 ZEXEL INJECTION-PUMP ASSEMBLY Calibration Data 1066711701 1156027341

Information Cross number Calibration Data Calibration Data Ex

Price: query
Buy now
Add to cart Go to cart

Rating:

Buy INJECTION-PUMP ASSEMBLY 106671-1701 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

ZEXEL 106671-1701 1066711701

ISUZU 1156027341 1156027341

Service parts 106671-1701 INJECTION-PUMP ASSEMBLY:

1. _

2. FUEL INJECTION PUMP 106061-7320

3. GOVERNOR 105489-3310

4. SUPPLY PUMP 105237-1430

5. AUTOM. ADVANCE MECHANIS 105636-1580

6. COUPLING PLATE 105663-0220

7. COUPLING PLATE

8. _

9. _

10. NOZZLE AND HOLDER ASSY 105100-6991

11. Nozzle and Holder 1-15300-159-1

12. Open Pre:MPa(Kqf/cm2) 19.6{200}

13. NOZZLE-HOLDER 105030-4271

14. NOZZLE 105015-6660

15. NOZZLE SET

Include in #1:

106671-1701 as INJECTION-PUMP ASSEMBLY

Cross reference number

ZEXEL 106671-1701 1066711701

ISUZU 1156027341 1156027341

Zexel num

Bosch num

Firm num

Name

106671-1701
106671-1702

1156027341 ISUZU

INJECTION-PUMP ASSEMBLY
6RB1-TC * K

Calibration Data:

Adjustment conditions

Test oil
1404 Test oil ISO4113 or {SAEJ967d}

Test oil temperature degC 40 40 45

Nozzle and nozzle holder 105780-8140

Bosch type code EF8511/9A

Nozzle 105780-0000

Bosch type code DN12SD12T

Nozzle holder 105780-2080

Bosch type code EF8511/9

Opening pressure MPa 17.2

Opening pressure kgf/cm2 175

Injection pipe
Outer diameter - inner diameter - length (mm) mm 8-3-600

Overflow valve 134424-1920

Overflow valve opening pressure kPa 127 107 147

Overflow valve opening pressure kgf/cm2 1.3 1.1 1.5

Tester oil delivery pressure kPa 157 157 157

Tester oil delivery pressure kgf/cm2 1.6 1.6 1.6

Direction of rotation (viewed from drive side)
Right R

Injection timing adjustment

Direction of rotation (viewed from drive side)
Right R

Injection order 1-4-2-6- 3-5

Pre-stroke mm 3.8 3.77 3.83

Beginning of injection position
Drive side NO.1

Difference between angles 1
Cal 1-4 deg. 60 59.75 60.25

Difference between angles 2
Cyl.1-2 deg. 120 119.75 120.25

Difference between angles 3
Cal 1-6 deg. 180 179.75 180.25

Difference between angles 4
Cal 1-3 deg. 240 239.75 240.25

Difference between angles 5
Cal 1-5 deg. 300 299.75 300.25

Injection quantity adjustment

Adjusting point B

Rack position 8.6

Pump speed r/min 600 600 600

Average injection quantity mm3/st. 151 149 153

Max. variation between cylinders % 0 -3 3

Basic *

Fixing the lever *

Boost pressure kPa 28.7 28.7

Boost pressure mmHg 215 215

Injection quantity adjustment_02

Adjusting point C

Rack position 5.5+-0.5

Pump speed r/min 225 225 225

Average injection quantity mm3/st. 10 6.8 13.2

Max. variation between cylinders % 0 -13 13

Fixing the rack *

Boost pressure kPa 0 0 0

Boost pressure mmHg 0 0 0

Injection quantity adjustment_03

Adjusting point D

Rack position -

Pump speed r/min 150 150 150

Average injection quantity mm3/st. 96 96

Fixing the lever *

Boost pressure kPa 0 0 0

Boost pressure mmHg 0 0 0

Boost compensator adjustment

Pump speed r/min 500 500 500

Rack position 7.35

Boost pressure kPa 6.7 5.4 8

Boost pressure mmHg 50 40 60

Boost compensator adjustment_02

Pump speed r/min 500 500 500

Rack position 8.6

Boost pressure kPa 15.3 15.3 15.3

Boost pressure mmHg 115 115 115

Timer adjustment

Pump speed r/min 750--

Advance angle deg. 0 0 0

Remarks
Start

Timer adjustment_02

Pump speed r/min 700

Advance angle deg. 0.5

Timer adjustment_03

Pump speed r/min 1000

Advance angle deg. 1 0.5 1.5

Remarks
Finish

Test data Ex:

Governor adjustment

N:Pump speed R:Rack position (mm) (1)Tolerance for racks not indicated: +-0.05mm. (2)Damper spring setting (3)Boost compensator stroke: BCL
----------
BCL=1.25+-0.1mm
----------

Speed control lever angle

F:Full speed
----------

----------
a=3.5deg+-5deg

0000000901

F:Full load I:Idle (1)Use the hole at R = aa (2)Stopper bolt setting
----------
aa=32mm
----------
a=30deg+-5deg b=37deg+-3deg

Stop lever angle

N:Pump normal S:Stop the pump.
----------

----------
a=32deg+-5deg b=64deg+-5deg

Timing setting

(1)Pump vertical direction (2)Position of timer's threaded hole at No 1 cylinder's beginning of injection (3)B.T.D.C.: aa (4)-
----------
aa=18deg
----------
a=(70deg)