106671-1582 ZEXEL INJECTION-PUMP ASSEMBLY Calibration Data 1066711582 1156025174

Information Cross number Calibration Data Calibration Data Ex

Price: query
Buy now
Add to cart Go to cart

Rating:

Buy INJECTION-PUMP ASSEMBLY 106671-1582 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

ZEXEL 106671-1582 1066711582

ISUZU 1156025174 1156025174

Service parts 106671-1582 INJECTION-PUMP ASSEMBLY:

1. _

2. FUEL INJECTION PUMP 106061-5370

3. GOVERNOR 105952-0461

4. SUPPLY PUMP 105237-1920

5. AUTOM. ADVANCE MECHANIS 105691-3461

6. COUPLING PLATE 105663-0410

7. COUPLING PLATE

8. _

9. _

10. NOZZLE AND HOLDER ASSY 105101-6051

11. Nozzle and Holder 1-15300-244-1

12. Open Pre:MPa(Kqf/cm2) 22.1{225}

13. NOZZLE-HOLDER 105030-4271

14. NOZZLE 105015-8110

15. NOZZLE SET

Include in #1:

106671-1582 as INJECTION-PUMP ASSEMBLY

Cross reference number

ZEXEL 106671-1582 1066711582

ISUZU 1156025174 1156025174

Zexel num

Bosch num

Firm num

Name

106671-1582
106671-1583

1156025174 ISUZU

INJECTION-PUMP ASSEMBLY
6RB1-TC1 * K 14CA PE6P,6PD PE

Calibration Data:

Adjustment conditions

Test oil
1404 Test oil ISO4113 or {SAEJ967d}

Test oil temperature degC 40 40 45

Nozzle and nozzle holder 105780-8140

Bosch type code EF8511/9A

Nozzle 105780-0000

Bosch type code DN12SD12T

Nozzle holder 105780-2080

Bosch type code EF8511/9

Opening pressure MPa 17.2

Opening pressure kgf/cm2 175

Injection pipe
Outer diameter - inner diameter - length (mm) mm 8-3-600

Overflow valve 134424-1920

Overflow valve opening pressure kPa 157 123 191

Overflow valve opening pressure kgf/cm2 1.6 1.25 1.95

Tester oil delivery pressure kPa 255 255 255

Tester oil delivery pressure kgf/cm2 2.6 2.6 2.6

RED3 control unit part number 407910-2 470

RED3 rack sensor specifications mm 15

Direction of rotation (viewed from drive side)
Right R

Injection timing adjustment

Direction of rotation (viewed from drive side)
Right R

Injection order 1-4-2-6- 3-5

Pre-stroke mm 3.2 3.17 3.23

Beginning of injection position
Drive side NO.1

Difference between angles 1
Cal 1-4 deg. 60 59.75 60.25

Difference between angles 2
Cyl.1-2 deg. 120 119.75 120.25

Difference between angles 3
Cal 1-6 deg. 180 179.75 180.25

Difference between angles 4
Cal 1-3 deg. 240 239.75 240.25

Difference between angles 5
Cal 1-5 deg. 300 299.75 300.25

Injection quantity adjustment

Rack position (12.2)

Vist V 1.56 1.56 1.56

Pump speed r/min 800 800 800

Average injection quantity mm3/st. 149 147.5 150.5

Max. variation between cylinders % 0 -3 3

Basic *

Injection quantity adjustment_02

Rack position (7.2)

Vist V 2.6 2.5 2.7

Pump speed r/min 225 225 225

Average injection quantity mm3/st. 8.5 6.5 10.5

Max. variation between cylinders % 0 -13 13

Test data Ex:

Governor adjustment

(1)Adjusting range (2)Step response time (N): Speed of the pump (L): Load (theta) Advance angle (Srd1) Step response time 1 (Srd2) Step response time 2 1. Adjusting conditions for the variable timer (1)Adjust the clearance between the pickup and the protrusion to L.
----------
L=1-0.2mm N2=800r/min C2=(8)deg t1=1.7--sec. t2=1.7--sec.
----------
N1=950++r/min P1=0kPa(0kgf/cm2) P2=392kPa(4kgf/cm2) C1=8+-0.3deg R01=0/4load R02=4/4load

0000000901

(1)Pump vertical direction (2)Position of timer's threaded hole at No 1 cylinder's beginning of injection (3)B.T.D.C.: aa (4)-
----------
aa=11deg
----------
a=(70deg)

Stop lever angle

(Rs) rack sensor specifications (C/U) control unit part number (V) Rack sensor output voltage (R) Rack position (mm) 1. Confirming governor output characteristics (rack 15 mm, span 6 mm) (1)When the output voltages of the rack sensor are V1 and V2, check that the rack positions R1 and R2 in the table above are satisfied.
----------

----------