106671-1441 ZEXEL INJECTION-PUMP ASSEMBLY Calibration Data 1066711441 1156021421


106671-1441 INJECTION-PUMP ASSEMBLY
Rating:
38
Buy INJECTION-PUMP ASSEMBLY 106671-1441 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

ZEXEL 106671-1441 1066711441
ISUZU 1156021421 1156021421

Cross reference number

ZEXEL 106671-1441 1066711441
ISUZU 1156021421 1156021421


Zexel num
Bosch num
Firm num
Name
106671-1441 
106671-1449 
 
1156021421  ISUZU
INJECTION-PUMP ASSEMBLY
6SD1X *

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil
  ISO4113 or {SAEJ967d}
Test oil temperature degC   40 40 45
Nozzle and nozzle holder   105780-8140
Bosch type code   EF8511/9A
Nozzle   105780-0000
Bosch type code   DN12SD12T
Nozzle holder   105780-2080
Bosch type code   EF8511/9
Opening pressure MPa   17.2
Opening pressure kgf/cm2   175
Injection pipe
Outer diameter - inner diameter - length (mm)
mm   8-3-600
Overflow valve   134424-1920
Overflow valve opening pressure kPa   127 107 147
Overflow valve opening pressure kgf/cm2   1.3 1.1 1.5
Tester oil delivery pressure kPa   157 157 157
Tester oil delivery pressure kgf/cm2   1.6 1.6 1.6
RED3 control unit part number   407910-2 470
RED3 rack sensor specifications mm   15
Direction of rotation (viewed from drive side)
Left
  L
Injection timing adjustment
Direction of rotation (viewed from drive side)
Left
  L
Injection order   1-5-3-6- 2-4
Pre-stroke mm   4.2 4.17 4.23
Beginning of injection position
Governor side
  NO.1
Difference between angles 1
Cal 1-5
deg.   60 59.75 60.25
Difference between angles 2
Cal 1-3
deg.   120 119.75 120.25
Difference between angles 3
Cal 1-6
deg.   180 179.75 180.25
Difference between angles 4
Cyl.1-2
deg.   240 239.75 240.25
Difference between angles 5
Cal 1-4
deg.   300 299.75 300.25
Injection quantity adjustment
Rack position   (12.4)
Vist V   1.53 1.53 1.53
Pump speed r/min   800 800 800
Average injection quantity mm3/st.   151.7 149.7 153.7
Max. variation between cylinders %   0 -3 3
Basic   *
Injection quantity adjustment_02
Rack position   (6+-0.5)
Vist V   2.8 2.7 2.9
Pump speed r/min   225 225 225
Average injection quantity mm3/st.   8.9 5.7 12.1
Max. variation between cylinders %   0 -13 13

Test data Ex:

Governor adjustment

Test data 106671-1441
(1)Adjusting range (2)Step response time (N): Speed of the pump (L): Load (theta) Advance angle (Srd1) Step response time 1 (Srd2) Step response time 2 1. Adjusting conditions for the variable timer (1)Adjust the clearance between the pickup and the protrusion to L.
----------
L=1-0.2mm N2=800r/min C2=(5.5deg) t1=2--sec. t2=2--sec.
----------
N1=800++r/min P1=0kPa(0kgf/cm2) P2=392kPa(4kgf/cm2) C1=5.5+-0.3deg R01=0/4load R02=4/4load

0000000901

Test data 106671-1441
(1)Pump vertical direction (2)Position of timer's threaded hole at No 1 cylinder's beginning of injection (3)- (4)-
----------

----------
a=(40deg)

Stop lever angle

Test data 106671-1441
(Rs) rack sensor specifications (C/U) control unit part number (V) Rack sensor output voltage (R) Rack position (mm) 1. Confirming governor output characteristics (rack 15 mm, span 6 mm) (1)When the output voltages of the rack sensor are V1 and V2, check that the rack positions R1 and R2 in the table above are satisfied.
----------

----------




Have questions with 106671-1441?





Group cross 106671-1441 ZEXEL

Isuzu 

 
1156021420 
INJECTION-PUMP ASSEMBLY
6SD1X
106671-1441  

106671-1449 
 
1156021421 
INJECTION-PUMP ASSEMBLY
6SD1X
 
1156021422 
INJECTION-PUMP ASSEMBLY
6SD1X
 
1156021423 
INJECTION-PUMP ASSEMBLY
6SD1X
 
1156021424 
INJECTION-PUMP ASSEMBLY
6SD1X
 
1156021425 
INJECTION-PUMP ASSEMBLY
6SD1TC
 
1156021426 
INJECTION-PUMP ASSEMBLY
6SD1-TC
 
1156021427 
INJECTION-PUMP ASSEMBLY
6SD1-TC2
 
1156021428 
INJECTION-PUMP ASSEMBLY
6SD1-TC2
9 400 616 707 
1156021429 
INJECTION-PUMP ASSEMBLY
6SD1-TC2
Back to top