106671-0150 ZEXEL INJECTION-PUMP ASSEMBLY Calibration Data 1066710150


106671-0150 INJECTION-PUMP ASSEMBLY
Rating:
13
Buy INJECTION-PUMP ASSEMBLY 106671-0150 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

ZEXEL 106671-0150 1066710150

Service parts 106671-0150 INJECTION-PUMP ASSEMBLY:

1. _
2. FUEL INJECTION PUMP 106060-5430
3. GOVERNOR 105488-9480
4. SUPPLY PUMP 105217-4000
5. AUTOM. ADVANCE MECHANIS 105691-0201
6. COUPLING PLATE 105662-0880
7. COUPLING PLATE
8. _
9. _
10. NOZZLE AND HOLDER ASSY 105100-7130
11. Nozzle and Holder 16600-96514
12. Open Pre:MPa(Kqf/cm2) 17.7{180}/22.6{230}
13. NOZZLE-HOLDER 105031-4630
14. NOZZLE 105015-6340
15. NOZZLE SET

Include in #1:

106671-0150 as INJECTION-PUMP ASSEMBLY

Cross reference number

ZEXEL 106671-0150 1066710150


Zexel num
Bosch num
Firm num
Name
106671-0150 
106671-0152 
 
  NISSAN-DIESEL
INJECTION-PUMP ASSEMBLY
PE6TB *

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil
  ISO4113 or {SAEJ967d}
Test oil temperature degC   40 40 45
Nozzle and nozzle holder   105780-8140
Bosch type code   EF8511/9A
Nozzle   105780-0000
Bosch type code   DN12SD12T
Nozzle holder   105780-2080
Bosch type code   EF8511/9
Opening pressure MPa   17.2
Opening pressure kgf/cm2   175
Injection pipe
Outer diameter - inner diameter - length (mm)
mm   8-3-600
Overflow valve opening pressure kPa   157 123 191
Overflow valve opening pressure kgf/cm2   1.6 1.25 1.95
Tester oil delivery pressure kPa   157 157 157
Tester oil delivery pressure kgf/cm2   1.6 1.6 1.6
Direction of rotation (viewed from drive side)
Right
  R
Injection timing adjustment
Direction of rotation (viewed from drive side)
Right
  R
Injection order   1-4-2-6- 3-5
Pre-stroke mm   3.65 3.6 3.7
Beginning of injection position
Drive side
  NO.1
Difference between angles 1
Cal 1-4
deg.   60 59.5 60.5
Difference between angles 2
Cyl.1-2
deg.   120 119.5 120.5
Difference between angles 3
Cal 1-6
deg.   180 179.5 180.5
Difference between angles 4
Cal 1-3
deg.   240 239.5 240.5
Difference between angles 5
Cal 1-5
deg.   300 299.5 300.5
Injection quantity adjustment
Adjusting point   A
Rack position   R2(12.5)
Pump speed r/min   1100 1100 1100
Average injection quantity mm3/st.   185.6 181.6 189.6
Max. variation between cylinders %   0 -5 5
Fixing the lever   *
Boost pressure kPa   33.3 33.3
Boost pressure mmHg   250 250
Injection quantity adjustment_02
Adjusting point   B
Rack position   12.1
Pump speed r/min   600 600 600
Average injection quantity mm3/st.   171 169 173
Max. variation between cylinders %   0 -4 4
Basic   *
Fixing the lever   *
Boost pressure kPa   33.3 33.3
Boost pressure mmHg   250 250
Injection quantity adjustment_03
Adjusting point   C
Rack position   7.4+-0.5
Pump speed r/min   225 225 225
Average injection quantity mm3/st.   10.1 9.1 11.1
Max. variation between cylinders %   0 -10 10
Fixing the rack   *
Boost pressure kPa   0 0 0
Boost pressure mmHg   0 0 0
Injection quantity adjustment_04
Adjusting point   D
Rack position   R1(10.7)
Pump speed r/min   300 300 300
Average injection quantity mm3/st.   120.6 118.6 122.6
Fixing the lever   *
Boost pressure kPa   0 0 0
Boost pressure mmHg   0 0 0
Injection quantity adjustment_05
Adjusting point   E
Rack position   R2+0.2
Pump speed r/min   300 300 300
Average injection quantity mm3/st.   186.3 176.3 196.3
Fixing the lever   *
Rack limit   *
Boost compensator adjustment
Pump speed r/min   300 300 300
Rack position   R1(10.7)
Boost pressure kPa   4
Boost pressure mmHg   30
Boost compensator adjustment_02
Pump speed r/min   300 300 300
Rack position   R2+0.2
Boost pressure kPa   20 20 20
Boost pressure mmHg   150 150 150

Test data Ex:

Governor adjustment

Test data 106671-0150
N:Pump speed R:Rack position (mm) (1)Lever ratio: RT (2)Target shim dimension: TH (3)Damper spring setting: DL (4)Rack limit using stop lever
----------
RT=1 TH=2.7mm DL=6.4-0.2mm
----------

Timer adjustment

Test data 106671-0150
(1)Adjusting range (2)Step response time (N): Speed of the pump (L): Load (theta) Advance angle (Srd1) Step response time 1 (Srd2) Step response time 2 1. Adjusting conditions for the variable timer (1)Adjust the clearance between the pickup and the protrusion to L.
----------
L=1-0.2mm N2=800r/min C2=(6.5)deg t1=2--sec. t2=2--sec.
----------
N1=1250++r/min P1=0kPa(0kgf/cm2) P2=392kPa(4kgf/cm2) C1=6.5+-0.5deg R01=0/4load R02=4/4load

Speed control lever angle

Test data 106671-0150
F:Full speed
----------

----------
a=30deg+-5deg

0000000901

Test data 106671-0150
F:Full load I:Idle (1)Stopper bolt setting (2)At center of threaded hole above R = aa
----------
aa=17mm
----------
a=22deg+-5deg b=33deg+-3deg

Stop lever angle

Test data 106671-0150
N:Pump normal S:Stop the pump. (1)Rack position = aa (2)Rack position bb, pump speed cc (3)Adjust after setting excess fuel lever.
----------
aa=R2(12.5)+0.2mm bb=1+0.5mm cc=0r/min
----------
a=20.5deg+-5deg b=33.5deg+-5deg

0000001101

Test data 106671-0150
N:Normal B:When boosted (1)Rack position = aa
----------
aa=13mm
----------
a=(18deg) b=(32deg)

0000001501 RACK SENSOR

Test data 106671-0150
V1:Supply voltage V2f:Full side output voltage V2i:Idle side output voltage (A) Black (B) Yellow (C) Red (D) Trimmer (E): Shaft (F) Nut (G) Load lever 1. Load sensor adjustment (1)Connect as shown in the above diagram and apply supply voltage V1. (2)Hold the load lever (G) against the full side. (3)Turn the shaft so that the voltage between (A) and (B) is V2. (4)Hold the load lever (G) against the idle side. (5)Adjust (D) so that the voltage between (A) and (B) is V2i. (6)Repeat the above adjustments. (7)Tighten the nut (F) at the point satisfying the standards. (8)Hold the load lever against the full side stopper and the idle side stopper. (9)At this time, confirm that the full side output voltage is V2f and the idle side output voltage is V2i.
----------
V1= 5+-0.02V V2f=0.3+0.03V V2i=2.2-0.03V
----------

Timing setting

Test data 106671-0150
(1)Pump vertical direction (2)Coupling's key groove position at No 1 cylinder's beginning of injection (3)- (4)-
----------

----------
a=(20deg)




Have questions with 106671-0150?





Group cross 106671-0150 ZEXEL

Nissan-Diesel 

 
 
INJECTION-PUMP ASSEMBLY
PE6TC
 
 
INJECTION-PUMP ASSEMBLY

Nissan-Diesel 

 
1680196504 
INJECTION-PUMP ASSEMBLY
PE6TC
 
 
INJECTION-PUMP ASSEMBLY
PE6TB
 
 
INJECTION-PUMP ASSEMBLY

Nissan-Diesel 

 
1680196505 
INJECTION-PUMP ASSEMBLY
PE6TB
 
 
INJECTION-PUMP ASSEMBLY
PE6T
 
1671396678 
INJECTION-PUMP ASSEMBLY
PE6T
 
 
INJECTION-PUMP ASSEMBLY
PE6T
 
 
INJECTION-PUMP ASSEMBLY

Nissan-Diesel 

 
1680096560 
INJECTION-PUMP ASSEMBLY
PE6T
 
 
INJECTION-PUMP ASSEMBLY
PE6TC
 
 
INJECTION-PUMP ASSEMBLY

Nissan-Diesel 

 
1680096561 
INJECTION-PUMP ASSEMBLY
PE6TC
106671-0150  

106671-0152 
 
 
INJECTION-PUMP ASSEMBLY
PE6TB
 
 
INJECTION-PUMP ASSEMBLY

Nissan-Diesel 

 
1680096562 
INJECTION-PUMP ASSEMBLY
PE6TB
 
 
INJECTION-PUMP ASSEMBLY

Nissan-Diesel 

 
1680096565 
INJECTION-PUMP ASSEMBLY
PE6TB
 
1680196506 
INJECTION-PUMP ASSEMBLY
PE6T
 
1680196507 
INJECTION-PUMP ASSEMBLY
PE6TC
Back to top