Rating:
Information injection-pump assembly
ZEXEL
104760-2320
1047602320
Cross reference number
ZEXEL
104760-2320
1047602320
Zexel num
Bosch num
Firm num
Name
Calibration Data:
Adjustment conditions
Test oil
1404 Test oil ISO4113orSAEJ967d
1404 Test oil ISO4113orSAEJ967d
Test oil temperature
degC
45
45
50
Nozzle
105780-0060
Bosch type code
NP-DN0SD1510
Nozzle holder
105780-2150
Opening pressure
MPa
13
13
13.3
Opening pressure
kgf/cm2
133
133
136
Injection pipe
157805-7320
Injection pipe
Inside diameter - outside diameter - length (mm) mm 2-6-450
Inside diameter - outside diameter - length (mm) mm 2-6-450
Joint assembly
157641-4720
Tube assembly
157641-4020
Transfer pump pressure
kPa
20
20
20
Transfer pump pressure
kgf/cm2
0.2
0.2
0.2
Direction of rotation (viewed from drive side)
Right R
Right R
Injection timing adjustment
Pump speed
r/min
900
900
900
Average injection quantity
mm3/st.
32.3
32.1
32.5
Difference in delivery
mm3/st.
2
Basic
*
Injection timing adjustment_02
Pump speed
r/min
2600
2600
2600
Average injection quantity
mm3/st.
27
24.5
29.5
Injection timing adjustment_03
Pump speed
r/min
2500
2500
2500
Average injection quantity
mm3/st.
31.7
29.6
33.8
Injection timing adjustment_04
Pump speed
r/min
2300
2300
2300
Average injection quantity
mm3/st.
31.4
29.4
33.4
Injection timing adjustment_05
Pump speed
r/min
1800
1800
1800
Average injection quantity
mm3/st.
33.1
31.1
35.1
Injection timing adjustment_06
Pump speed
r/min
1200
1200
1200
Average injection quantity
mm3/st.
32.1
30.6
33.6
Injection timing adjustment_07
Pump speed
r/min
900
900
900
Average injection quantity
mm3/st.
32.3
31.6
33
Injection timing adjustment_08
Pump speed
r/min
600
600
600
Average injection quantity
mm3/st.
32.9
31.1
34.7
Injection quantity adjustment
Pump speed
r/min
2600
2600
2600
Average injection quantity
mm3/st.
27
25
29
Difference in delivery
mm3/st.
4.5
Basic
*
Injection quantity adjustment_02
Pump speed
r/min
2800
2800
2800
Average injection quantity
mm3/st.
6.5
Governor adjustment
Pump speed
r/min
290
290
290
Average injection quantity
mm3/st.
9
8
10
Difference in delivery
mm3/st.
1.7
Basic
*
Governor adjustment_02
Pump speed
r/min
290
290
290
Average injection quantity
mm3/st.
9
8
10
Governor adjustment_03
Pump speed
r/min
500
500
500
Average injection quantity
mm3/st.
3
Boost compensator adjustment
Pump speed
r/min
600
600
600
Average injection quantity
mm3/st.
16.9
10.9
22.9
Remarks
Refer to additional devices.
Refer to additional devices.
Timer adjustment
Pump speed
r/min
100
100
100
Average injection quantity
mm3/st.
40
40
Difference in delivery
mm3/st.
15
Basic
*
Speed control lever angle
Pump speed
r/min
290
290
290
Average injection quantity
mm3/st.
4
Remarks
Magnet OFF
Magnet OFF
Speed control lever angle_02
Pump speed
r/min
900
900
900
Average injection quantity
mm3/st.
0
0
0
Remarks
Magnet OFF
Magnet OFF
0000000901
Pump speed
r/min
900
900
900
Overflow quantity
cm3/min
390
258
522
Stop lever angle
Pump speed
r/min
900
900
900
Pressure
kPa
372.5
343
402
Pressure
kgf/cm2
3.8
3.5
4.1
Basic
*
Stop lever angle_02
Pump speed
r/min
900
900
900
Pressure
kPa
372.5
343
402
Pressure
kgf/cm2
3.8
3.5
4.1
Stop lever angle_03
Pump speed
r/min
1800
1800
1800
Pressure
kPa
578.5
549
608
Pressure
kgf/cm2
5.9
5.6
6.2
Stop lever angle_04
Pump speed
r/min
2500
2500
2500
Pressure
kPa
745.5
716
775
Pressure
kgf/cm2
7.6
7.3
7.9
0000001101
Pump speed
r/min
900
900
900
Timer stroke
mm
3.2
3
3.4
Basic
*
_02
Pump speed
r/min
900
900
900
Timer stroke
mm
3.2
3
3.4
_03
Pump speed
r/min
1200
1200
1200
Timer stroke
mm
4.9
4.5
5.3
_04
Pump speed
r/min
1800
1800
1800
Timer stroke
mm
8.5
7.9
9.1
_05
Pump speed
r/min
2300
2300
2300
Timer stroke
mm
9.75
9.3
10.2
0000001201
Max. applied voltage
V
8
8
8
Test voltage
V
13
12
14
Timing setting
K dimension
mm
3.3
3.2
3.4
KF dimension
mm
7.24
7.14
7.34
MS dimension
mm
1.8
1.7
1.9
Control lever angle alpha
deg.
25
21
29
Control lever angle beta
deg.
42
37
47
Control lever angle gamma
deg.
11
10.5
11.5
Test data Ex:
0000001801 W-CSD ADJUSTMENT
Adjustment of the W-CSD
Adjust the timer stroke using the screw so that it is as determined from the graph.
Caution: The temperature of the wax at adjustment must not exceed a.
A:Screw
B:Timer stroke graph
X:Temperature t
Y:Timer stroke TA
----------
a=30degC
----------
----------
a=30degC
----------
0000001901 DASHPOT ADJUSTMENT
Adjustment of the dash pot
1. Insert a block gauge L1 (thickness gauge) between the idle set screw (C) and the control lever (D).
2. In the above condition, adjust the position of the dash pot so that the dash pot adjustment screw (A) contacts the push rod and then fix the screw using the nut (B).
TT
Note:
(1)Confirm that the dashpot and control lever contact faces are smooth.
(2)Confirm that the control lever returns to the idling position.
ISC actuator installation
1. Maintain the control lever in the idling position.
2. Fix actuator bracket (F) so that the gap between the control lever and the ISC lever's roller (E) is L2.
----------
T=6~7N-m(0.6~0.7kgf-m) L1=2.7+-0.05mm L2=1.0+1.0-0.5mm
----------
L1=2.7+-0.05mm L2=1.0+1.0-0.5mm
----------
T=6~7N-m(0.6~0.7kgf-m) L1=2.7+-0.05mm L2=1.0+1.0-0.5mm
----------
L1=2.7+-0.05mm L2=1.0+1.0-0.5mm
0000002001 POTENTIOMETER ADJUSTMENT
Adjustment of the potentiometer
In the following condition, change the installation position of the potentiometer to adjust the output voltage to within the specified values.
Measure the injection quantity at control lever position a (shim thickness = approximately L mm) at N = N1 r/min, determine the voltage using the formula, and adjust the potentiometer.
A:Performance standards
C:Position of the control lever
N:Pump speed
Vo:Output voltage
E:Conversion formula
G:Idling
H:Full speed
K:Applied voltage
X:Injection quantity (cm3/1,000st)
Y:Voltage (V)
R:At target value Q1cm3/1,000 st, set voltage at V3 (V).
M:The switch voltage specification is the value when the full lever position is V6.
B:Conversion point
B1:ON-->OFF
B2:OFF-->ON
D:Lever opening (from idle)
----------
N1=600r/min a=10.3deg L=5.6mm Q1=-cm3/1,000st V3=-V V6=-V
----------
V1=0.5 or more V V2=9.6 or less V V4=-V V5=-V K=10V D1=5.0+-2.5deg D2=23.5 or more deg J:V+-0.03=0.0459X+2.4219
----------
N1=600r/min a=10.3deg L=5.6mm Q1=-cm3/1,000st V3=-V V6=-V
----------
V1=0.5 or more V V2=9.6 or less V V4=-V V5=-V K=10V D1=5.0+-2.5deg D2=23.5 or more deg J:V+-0.03=0.0459X+2.4219