104742-3011 ZEXEL INJECTION-PUMP ASSEMBLY Calibration Data 1047423011 32a6527320


104742-3011 INJECTION-PUMP ASSEMBLY
Rating:
48
Buy INJECTION-PUMP ASSEMBLY 104742-3011 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

ZEXEL 104742-3011 1047423011
MITSUBISHI-HEAV 32A6527320 32a6527320

Cross reference number

ZEXEL 104742-3011 1047423011
MITSUBISHI-HEAV 32A6527320 32a6527320


Zexel num
Bosch num
Firm num
Name
104742-3011 
 
32A6527320  MITSUBISHI-HEAV
INJECTION-PUMP ASSEMBLY
S4S-DT

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil
  ISO4113orSAEJ967d
Test oil temperature degC   45 45 50
Nozzle   105780-0060
Bosch type code   NP-DN0SD1510
Nozzle holder   105780-2150
Opening pressure MPa   13 13 13.3
Opening pressure kgf/cm2   133 133 136
Injection pipe   157805-7320
Injection pipe
Inside diameter - outside diameter - length (mm)
mm   2-6-450
Joint assembly   157641-4720
Tube assembly   157641-4020
Transfer pump pressure kPa   20 20 20
Transfer pump pressure kgf/cm2   0.2 0.2 0.2
Direction of rotation (viewed from drive side)
Right
  R
(Solenoid timer adjustment condition)
With S/T O-ring; S/T OFF.
  OFF
Timer measuring device installation position
Low pressure side
  LOW PRESSURE SIDE
Injection timing adjustment
Pump speed r/min   900 900 900
Average injection quantity mm3/st.   120.7 120.2 121.2
Difference in delivery mm3/st.   11
Basic   *
Oil temperature degC   50 48 52
Injection timing adjustment_02
Pump speed r/min   500 500 500
Average injection quantity mm3/st.   78.2 71.7 84.7
Oil temperature degC   48 46 50
Injection timing adjustment_03
Pump speed r/min   900 900 900
Average injection quantity mm3/st.   120.7 118.2 123.2
Difference in delivery mm3/st.   11.5
Basic   *
Oil temperature degC   50 48 52
Injection timing adjustment_04
Pump speed r/min   1100 1100 1100
Average injection quantity mm3/st.   123.9 118.4 129.4
Oil temperature degC   50 48 52
Injection timing adjustment_05
Pump speed r/min   1250 1250 1250
Average injection quantity mm3/st.   120.1 114.6 125.6
Oil temperature degC   50 48 52
Injection quantity adjustment
Pump speed r/min   1425 1425 1425
Average injection quantity mm3/st.   5
Basic   *
Oil temperature degC   50 48 52
Injection quantity adjustment_02
Pump speed r/min   1425 1425 1425
Average injection quantity mm3/st.   6.5
Basic   *
Oil temperature degC   50 48 52
Injection quantity adjustment_03
Pump speed r/min   1300 1300 1300
Average injection quantity mm3/st.   111 111
Oil temperature degC   50 48 52
Remarks
(check)
 
Governor adjustment
Pump speed r/min   595 595 595
Average injection quantity mm3/st.   6 4 8
Difference in delivery mm3/st.   3
Basic   *
Oil temperature degC   50 48 52
Governor adjustment_02
Pump speed r/min   595 595 595
Average injection quantity mm3/st.   6 3.5 8.5
Difference in delivery mm3/st.   3.5
Basic   *
Oil temperature degC   50 48 52
Timer adjustment
Pump speed r/min   100 100 100
Average injection quantity mm3/st.   100 75 125
Basic   *
Oil temperature degC   48 46 50
Remarks
Full
 
Timer adjustment_02
Pump speed r/min   100 100 100
Average injection quantity mm3/st.   100 75 125
Oil temperature degC   48 46 50
Remarks
Full
 
Speed control lever angle
Pump speed r/min   595 595 595
Average injection quantity mm3/st.   0 0 0
Oil temperature degC   50 48 52
Remarks
Magnet OFF at idling position
 
Speed control lever angle_02
Pump speed r/min   595 595 595
Average injection quantity mm3/st.   0 0 0
Oil temperature degC   50 48 52
Remarks
Magnet ON at idling position and stop lever operate
 
0000000901
Pump speed r/min   1250 1250 1250
Overflow quantity with S/T ON cm3/min   540 410 670
Oil temperature degC   50 48 52
Stop lever angle
Pump speed r/min   1250 1250 1250
Pressure with S/T ON kPa   696 647 745
Pressure with S/T ON kgf/cm2   7.1 6.6 7.6
Pressure with S/T OFF kPa   530 510 550
Pressure with S/T OFF kgf/cm2   5.4 5.2 5.6
Basic   *
Oil temperature degC   50 48 52
Remarks
OFF
 
Stop lever angle_02
Pump speed r/min   900 900 900
Pressure with S/T OFF kPa   402 353 451
Pressure with S/T OFF kgf/cm2   4.1 3.6 4.6
Oil temperature degC   50 48 52
Stop lever angle_03
Pump speed r/min   1100 1100 1100
Pressure with S/T OFF kPa   481 432 530
Pressure with S/T OFF kgf/cm2   4.9 4.4 5.4
Oil temperature degC   50 48 52
Stop lever angle_04
Pump speed r/min   1250 1250 1250
Pressure with S/T ON kPa   696 637 755
Pressure with S/T ON kgf/cm2   7.1 6.5 7.7
Pressure with S/T OFF kPa   530 501 559
Pressure with S/T OFF kgf/cm2   5.4 5.1 5.7
Basic   *
Oil temperature degC   50 48 52
Remarks
OFF
 
0000001101
Pump speed r/min   1250 1250 1250
Timer stroke with S/T ON mm   4.9 4.4 5.3
Timer stroke with S/T OFF mm   3.3 3.1 3.5
Basic   *
Oil temperature degC   50 48 52
Remarks
OFF
 
_02
Pump speed r/min   900 900 900
Timer stroke with S/T OFF mm   0.9 0.2 1.6
Oil temperature degC   50 48 52
_03
Pump speed r/min   1100 1100 1100
Timer stroke with S/T OFF mm   2.4 1.8 3
Oil temperature degC   50 48 52
_04
Pump speed r/min   1250 1250 1250
Timer stroke with S/T ON mm   4.9 4.4 5.3
Timer stroke with S/T OFF mm   3.3 2.9 3.7
Basic   *
Oil temperature degC   50 48 52
Remarks
OFF
 
0000001201
Max. applied voltage V   8 8 8
Test voltage V   13 12 14
0000001401
Pump speed r/min   1250 1250 1250
Average injection quantity mm3/st.   95 93 97
Timer stroke TA mm   0 0 0.3
Timer stroke variation dT mm   3.3 3.3 3.3
Basic   *
Oil temperature degC   50 48 52
_02
Pump speed r/min   1250 1250 1250
Average injection quantity mm3/st.   112 110 114
Timer stroke TA mm   3.1 3.1
Timer stroke variation dT mm   0.2 0.2 0.2
Oil temperature degC   50 48 52
Remarks
(check)
 
_03
Pump speed r/min   1250 1250 1250
Average injection quantity mm3/st.   95 92.5 97.5
Timer stroke TA mm   0 0 0.5
Timer stroke variation dT mm   3.3 3.3 3.3
Basic   *
Oil temperature degC   50 48 52
_04
Pump speed r/min   1250 1250 1250
Average injection quantity mm3/st.   15 12.5 17.5
Timer stroke TA mm   4.2 3.4 5
Timer stroke variation dT mm   0.9 0.9 0.9
Oil temperature degC   50 48 52
Timing setting
K dimension mm   3.1 3 3.2
KF dimension mm   5.5 5.4 5.6
MS dimension mm   0.6 0.5 0.7
Pre-stroke mm   0.45 0.43 0.47
Control lever angle alpha deg.   16 12 20
Control lever angle beta deg.   30 25 35

Test data Ex:

0000001801 W-CSD ADJUSTMENT

Test data 104742-3011
Adjustment of the W-CSD Adjustment of the timer advance angle 1. Determine the timer advance angle using the graph (graph TA). 2. Adjust with the screw (A) so that the timer advance angle determined in item 1 is obtained. X:Temperature t (deg C) Y:Timer stroke TA (mm) (S) Cold advance (R) Cooling water temperature (deg C) (T) Timer piston stroke (mm) (B) Standard point
----------
TA=-0.0526t+3.44(-3<=t)
----------
a=20degC b=-3degC c=2.4+-0.4mm d=3.6+-0.6mm

0000001901 TAMPER PROOF

Test data 104742-3011
Tamperproof installation procedure A:Position of break B:Rubber vibration damper C:Nut D:Cap E:Nut F:Nut G:Cap L1:Inspection dimension Fig. 1 Regulating valve seal 1) Target breaking torque T1 2) Maximum allowable breaking torque T2 3) Because the cap and the regulating valve are fixed using the MEC process, the bolt cannot be loosened after the bolt has been broken. Fig.2 Full load adjusting screw 1) Confirm the position of the rubber vibration damper (B) and then tighten nut (C) to the torque T3. Fig. 3 Maximum speed adjusting screw 1) Tighten nut (E) to the torque T4. 2) To prevent nut (E) from turning together, fix (E) using the tool, then tighten nut (F) to torque T4.
----------
L1=23~28mm T1=5~6.9N-m(0.5~0.69kgf-m) T2=9N-m(0.9kgf-m) T3=7~9N-m(0.7~0.9kgf-m) T4=6~9N-m(0.6~0.9kgf-m)
----------
L1=23~28mm




Have questions with 104742-3011?





Group cross 104742-3011 ZEXEL

Mitsubishi-Heav 

F 01G 09W 0AV 
32A6517311 
INJECTION-PUMP ASSEMBLY
S4S-DT
F 01G 09W 0F9 
32A6527310 
INJECTION-PUMP ASSEMBLY
S4S-DT
F 01G 09W 0AW 
32A6517321 
INJECTION-PUMP ASSEMBLY
S4S-DT
104742-3011  
 
32A6527320 
INJECTION-PUMP ASSEMBLY
S4S-DT
F 01G 09W 0AX 
32A6517331 
INJECTION-PUMP ASSEMBLY
S4S-DT
 
32A6527330 
INJECTION-PUMP ASSEMBLY
S4S-DT
 
32A6537330 
INJECTION-PUMP ASSEMBLY
S4S-DT
F 01G 09W 0E4 
32A6507340 
INJECTION-PUMP ASSEMBLY
S4S-DT
F 01G 09W 0AT 
32A6507350 
INJECTION-PUMP ASSEMBLY
S4S-DT
F 01G 09W 0EC 
32A6537310 
INJECTION-PUMP ASSEMBLY
S4S-DT
F 01G 09W 0ED 
32A6537320 
INJECTION-PUMP ASSEMBLY
S4S-DT
F 01G 09W 0EE 
32A6547330 
INJECTION-PUMP ASSEMBLY
S4S-DT
F 01G 09W 0EF 
32A6507370 
INJECTION-PUMP ASSEMBLY
S4S-DT
F 01G 09W 0EG 
32A6507380 
INJECTION-PUMP ASSEMBLY
S4S-DT
Back to top