101697-9020 ZEXEL INJECTION-PUMP ASSEMBLY Calibration Data 1016979020 16713z6861


101697-9020 INJECTION-PUMP ASSEMBLY
Rating:
79
Buy INJECTION-PUMP ASSEMBLY 101697-9020 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

ZEXEL 101697-9020 1016979020
NISSAN-DIESEL 16713Z6861 16713z6861

Service parts 101697-9020 INJECTION-PUMP ASSEMBLY:

1. _
2. FUEL INJECTION PUMP 101069-5040
3. GOVERNOR 105921-9780
4. SUPPLY PUMP 105220-7010
5. AUTOM. ADVANCE MECHANIS 105672-4040
6. COUPLING PLATE 105662-1380
7. COUPLING PLATE
8. _
9. _
10. NOZZLE AND HOLDER ASSY 105101-7120
11. Nozzle and Holder 16600-Z5578
12. Open Pre:MPa(Kqf/cm2) 16.7{170}/21.6{220}
13. NOZZLE-HOLDER 105030-4140
14. NOZZLE 105015-8680
15. NOZZLE SET

Include in #1:

101697-9020 as INJECTION-PUMP ASSEMBLY

Cross reference number

ZEXEL 101697-9020 1016979020
NISSAN-DIESEL 16713Z6861 16713z6861


Zexel num
Bosch num
Firm num
Name
101697-9020 
101697-9021 
 
16713Z6861  NISSAN-DIESEL
INJECTION-PUMP ASSEMBLY
FE6TA * K

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil
  ISO4113 or {SAEJ967d}
Test oil temperature degC   40 40 45
Nozzle and nozzle holder   105780-8140
Bosch type code   EF8511/9A
Nozzle   105780-0000
Bosch type code   DN12SD12T
Nozzle holder   105780-2080
Bosch type code   EF8511/9
Opening pressure MPa   17.2
Opening pressure kgf/cm2   175
Injection pipe
Outer diameter - inner diameter - length (mm)
mm   6-2-600
Overflow valve   134424-1520
Overflow valve opening pressure kPa   162 147 177
Overflow valve opening pressure kgf/cm2   1.65 1.5 1.8
Tester oil delivery pressure kPa   157 157 157
Tester oil delivery pressure kgf/cm2   1.6 1.6 1.6
Direction of rotation (viewed from drive side)
Right
  R
Injection timing adjustment
Direction of rotation (viewed from drive side)
Right
  R
Injection order   1-4-2-6- 3-5
Pre-stroke mm   3.9 3.85 3.95
Beginning of injection position
Drive side
  NO.1
Difference between angles 1
Cal 1-4
deg.   60 59.5 60.5
Difference between angles 2
Cyl.1-2
deg.   120 119.5 120.5
Difference between angles 3
Cal 1-6
deg.   180 179.5 180.5
Difference between angles 4
Cal 1-3
deg.   240 239.5 240.5
Difference between angles 5
Cal 1-5
deg.   300 299.5 300.5
Injection quantity adjustment
Adjusting point   -
Rack position   13.7
Pump speed r/min   700 700 700
Average injection quantity mm3/st.   99.5 97.5 101.5
Max. variation between cylinders %   0 -3.5 3.5
Basic   *
Fixing the rack   *
Standard for adjustment of the maximum variation between cylinders   *
Injection quantity adjustment_02
Adjusting point   H
Rack position   10.1+-0. 5
Pump speed r/min   275 275 275
Average injection quantity mm3/st.   8.6 6.8 10.4
Max. variation between cylinders %   0 -10 10
Fixing the rack   *
Standard for adjustment of the maximum variation between cylinders   *
Injection quantity adjustment_03
Adjusting point   A
Rack position   R1(13.7)
Pump speed r/min   700 700 700
Average injection quantity mm3/st.   99.5 98.5 100.5
Basic   *
Fixing the lever   *
Boost pressure kPa   29.3 29.3
Boost pressure mmHg   220 220
Injection quantity adjustment_04
Adjusting point   B
Rack position   R1-0.05
Pump speed r/min   1400 1400 1400
Average injection quantity mm3/st.   103.5 100.3 106.7
Fixing the lever   *
Boost pressure kPa   29.3 29.3
Boost pressure mmHg   220 220
Injection quantity adjustment_05
Adjusting point   C
Rack position   R2[R1-0. 3]
Pump speed r/min   250 250 250
Average injection quantity mm3/st.   85.5 82.3 88.7
Fixing the lever   *
Boost pressure kPa   29.3 29.3
Boost pressure mmHg   220 220
Injection quantity adjustment_06
Adjusting point   D
Rack position   R2-1.3
Pump speed r/min   250 250 250
Average injection quantity mm3/st.   63 59.8 66.2
Fixing the lever   *
Boost pressure kPa   0 0 0
Boost pressure mmHg   0 0 0
Injection quantity adjustment_07
Adjusting point   I
Rack position   -
Pump speed r/min   150 150 150
Average injection quantity mm3/st.   89 89 109
Fixing the lever   *
Boost pressure kPa   0 0 0
Boost pressure mmHg   0 0 0
Rack limit   *
Boost compensator adjustment
Pump speed r/min   250 250 250
Rack position   R2-1.3
Boost pressure kPa   4 2.7 5.3
Boost pressure mmHg   30 20 40
Boost compensator adjustment_02
Pump speed r/min   250 250 250
Rack position   R2[R1+0. 3]
Boost pressure kPa   16 16 16
Boost pressure mmHg   120 120 120
Timer adjustment
Pump speed r/min   1170--
Advance angle deg.   0 0 0
Remarks
Start
 
Timer adjustment_02
Pump speed r/min   450
Advance angle deg.   1 0.5 1.5
Timer adjustment_03
Pump speed r/min   (530)
Advance angle deg.   0 0 0
Remarks
Measure the actual speed.
 
Timer adjustment_04
Pump speed r/min   1120
Advance angle deg.   0.5
Timer adjustment_05
Pump speed r/min   1400
Advance angle deg.   4.5 4 5
Remarks
Finish
 

Test data Ex:

Governor adjustment

Test data 101697-9020
N:Pump speed R:Rack position (mm) (1)Torque cam stamping: T1 (2)Tolerance for racks not indicated: +-0.05mm. (3)RACK LIMIT (4)Boost compensator stroke: BCL
----------
T1=N24 BCL=1.3+-0.1mm
----------

Speed control lever angle

Test data 101697-9020
F:Full speed I:Idle (1)Use the hole at R = aa (2)Stopper bolt setting
----------
aa=36mm
----------
a=25deg+-5deg b=(38deg)+-3deg

Stop lever angle

Test data 101697-9020
N:Pump normal S:Stop the pump. (1)Use the pin at R = aa
----------
aa=42mm
----------
a=40deg+-5deg b=25deg+-5deg

0000001501 RACK SENSOR

Test data 101697-9020
(VR) measurement voltage (I) Part number of the control unit (G) Apply red paint. (H): End surface of the pump 1. Rack limit adjustment (1)Fix the rack at the rack limit position Ra. (2)Install the shim (D) to the rod (C) and tighten nut (E). (3)Select a shim (D) so that the distance between the end surface of the pump and the nut (E) is L. (4)Release the rack fixing and mount the joint (B) and fix. (5)At this time, confirm that the shim (D) does not interfere with the joint (B). 2. Rack sensor adjustment (-0420) (1)Screw in the bobbin (A) until it contacts the joint (B). (2)Fix the speed control lever at the full side. (3)Set the speed to N1 r/min. (4)Adjust the depth that the bobbin (A) is screwed in so that the control unit's rack sensor output voltage is VR+-0.02 V, then tighten the nut (F). (5)Apply G at two places. Connecting part between the joint (B) and the nut (F) Connecting part between the joint (B) and the end surface of the pump (H)
----------
L=33-0.2mm N1=700r/min Ra=R1(13.7)mm
----------

Timing setting

Test data 101697-9020
(1)Pump vertical direction (2)Position of timer's threaded hole at No 1 cylinder's beginning of injection (3)- (4)-
----------

----------
a=(60deg)




Have questions with 101697-9020?





Group cross 101697-9020 ZEXEL

 
 
INJECTION-PUMP ASSEMBLY
FE6T

Nissan-Diesel 

9 400 616 167 
16713Z6862 
INJECTION-PUMP ASSEMBLY
FE6T
9 400 616 168 
16713Z6819 
INJECTION-PUMP ASSEMBLY
FE6T
101697-9020  

101697-9021 
 
16713Z6861 
INJECTION-PUMP ASSEMBLY
FE6TA
 
16713Z6978 
INJECTION-PUMP ASSEMBLY
FE6TA
9 400 616 169 
16714Z5518 
INJECTION-PUMP ASSEMBLY
FE6TA
9 400 616 170 
1671395313 
INJECTION-PUMP ASSEMBLY
NE6T
9 400 611 613 
 
INJECTION-PUMP ASSEMBLY
FE6T

Nissan-Diesel 

9 400 616 171 
16713Z6961 
INJECTION-PUMP ASSEMBLY
FE6T
9 400 616 172 
16714Z5510 
INJECTION-PUMP ASSEMBLY
FE6TA
9 400 616 173 
16714Z5511 
INJECTION-PUMP ASSEMBLY
FE6TA
9 400 616 174 
16714Z5512 
INJECTION-PUMP ASSEMBLY
FE6TB
9 400 616 175 
16714Z5513 
INJECTION-PUMP ASSEMBLY
FE6TB
9 400 611 526 
16714Z5571 
INJECTION-PUMP ASSEMBLY
FE6TA
Back to top