101696-9080 ZEXEL INJECTION-PUMP ASSEMBLY Calibration Data 1016969080 16713z6209


101696-9080 INJECTION-PUMP ASSEMBLY
Rating:
39
Buy INJECTION-PUMP ASSEMBLY 101696-9080 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

ZEXEL 101696-9080 1016969080
NISSAN-DIESEL 16713Z6209 16713z6209

Service parts 101696-9080 INJECTION-PUMP ASSEMBLY:

1. _
2. FUEL INJECTION PUMP 101069-5010
3. GOVERNOR 105921-7300
4. SUPPLY PUMP 105220-7050
5. AUTOM. ADVANCE MECHANIS 105614-3640
6. COUPLING PLATE 105661-0401
7. COUPLING PLATE
8. _
9. _
10. NOZZLE AND HOLDER ASSY 105101-5630
11. Nozzle and Holder 16600-Z5570
12. Open Pre:MPa(Kqf/cm2) 21.6{220}
13. NOZZLE-HOLDER 105031-4650
14. NOZZLE 105015-7370
15. NOZZLE SET

Include in #1:

101696-9080 as INJECTION-PUMP ASSEMBLY

Cross reference number

ZEXEL 101696-9080 1016969080
NISSAN-DIESEL 16713Z6209 16713z6209


Zexel num
Bosch num
Firm num
Name
101696-9080 
101696-9320 
 
16713Z6209  NISSAN-DIESEL
INJECTION-PUMP ASSEMBLY
FE6T * K

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil
  ISO4113 or {SAEJ967d}
Test oil temperature degC   40 40 45
Nozzle and nozzle holder   105780-8140
Bosch type code   EF8511/9A
Nozzle   105780-0000
Bosch type code   DN12SD12T
Nozzle holder   105780-2080
Bosch type code   EF8511/9
Opening pressure MPa   17.2
Opening pressure kgf/cm2   175
Injection pipe
Outer diameter - inner diameter - length (mm)
mm   6-2-600
Overflow valve   131424-1520
Overflow valve opening pressure kPa   157 123 191
Overflow valve opening pressure kgf/cm2   1.6 1.25 1.95
Tester oil delivery pressure kPa   157 157 157
Tester oil delivery pressure kgf/cm2   1.6 1.6 1.6
Direction of rotation (viewed from drive side)
Right
  R
Injection timing adjustment
Direction of rotation (viewed from drive side)
Right
  R
Injection order   1-4-2-6- 3-5
Pre-stroke mm   3.4 3.35 3.45
Beginning of injection position
Drive side
  NO.1
Difference between angles 1
Cal 1-4
deg.   60 59.5 60.5
Difference between angles 2
Cyl.1-2
deg.   120 119.5 120.5
Difference between angles 3
Cal 1-6
deg.   180 179.5 180.5
Difference between angles 4
Cal 1-3
deg.   240 239.5 240.5
Difference between angles 5
Cal 1-5
deg.   300 299.5 300.5
Injection quantity adjustment
Adjusting point   -
Rack position   12.5
Pump speed r/min   1500 1500 1500
Average injection quantity mm3/st.   83.7 82.1 85.3
Max. variation between cylinders %   0 -3.5 3.5
Basic   *
Fixing the rack   *
Standard for adjustment of the maximum variation between cylinders   *
Injection quantity adjustment_02
Adjusting point   H
Rack position   9.5+-0.5
Pump speed r/min   300 300 300
Average injection quantity mm3/st.   9.5 7.7 11.3
Max. variation between cylinders %   0 -10 10
Fixing the rack   *
Standard for adjustment of the maximum variation between cylinders   *
Injection quantity adjustment_03
Adjusting point   A
Rack position   R1(12.5)
Pump speed r/min   1500 1500 1500
Average injection quantity mm3/st.   83.7 82.7 84.7
Basic   *
Fixing the lever   *
Injection quantity adjustment_04
Adjusting point   B
Rack position   R1-0.55
Pump speed r/min   900 900 900
Average injection quantity mm3/st.   68.7 66.7 70.7
Fixing the lever   *
Injection quantity adjustment_05
Adjusting point   I
Rack position   -
Pump speed r/min   150 150 150
Average injection quantity mm3/st.   85 85 105
Fixing the lever   *
Rack limit   *
Timer adjustment
Pump speed r/min   1050--
Advance angle deg.   0 0 0
Remarks
Start
 
Timer adjustment_02
Pump speed r/min   1000
Advance angle deg.   0.5
Timer adjustment_03
Pump speed r/min   1500
Advance angle deg.   2 1.5 2.5
Remarks
Finish
 

Test data Ex:

Governor adjustment

Test data 101696-9080
N:Pump speed R:Rack position (mm) (1)Torque cam stamping: T1 (2)Tolerance for racks not indicated: +-0.05mm. (3)RACK LIMIT
----------
T1=C35
----------

Speed control lever angle

Test data 101696-9080
F:Full speed I:Idle (1)Use the hole at R = aa (2)Stopper bolt set position 'H'
----------
aa=100mm
----------
a=26.5deg+-5deg b=39deg+-3deg

Stop lever angle

Test data 101696-9080
N:Pump normal S:Stop the pump.
----------

----------
a=37deg+-5deg b=40deg+-5deg

0000001501 ACS

Test data 101696-9080
(A) Set screw (B) Push rod 1 (C) Push rod 2 (D) Cover 1. Aneroid compensator unit adjustment (1)Select the push rod 2 to obtain L2. (2)Screw in (A) to obtain L1. 2. Adjustment when mounting the governor. (1)Set the speed of the pump to N1 r/min and fix the control lever at the full set position. (2)Screw in the aneroid compensator to obtain the performance shown in the graph above. (3)As there is hysterisis, measure when the absolute pressure drops. (4)Hysterisis must not exceed rack position = h1.
----------
N1=1500r/min L1=(1.5)mm L2=11+-0.5mm h1=0.15mm
----------
Ra=R1(12.5)mm Rb=(R1-1)mm Pa=(86.6)+-2.7kPa((650)+-20mmHg) Pb=69.3+-0.7kPa(520+-5mmHg) Q1=83.7+-1cm3/1000st Q2=71+-3cm3/1000st

Timing setting

Test data 101696-9080
(1)Pump vertical direction (2)Position of timer's threaded hole at No 1 cylinder's beginning of injection (3)- (4)-
----------

----------
a=(60deg)




Have questions with 101696-9080?





Group cross 101696-9080 ZEXEL

Nissan-Diesel 

9 400 616 134 
16713Z6163 
INJECTION-PUMP ASSEMBLY
FE6TB
 
16713Z6119 
INJECTION-PUMP ASSEMBLY
FE6T
9 400 610 306 
 
INJECTION-PUMP ASSEMBLY

Nissan-Diesel 

9 400 616 135 
16713Z6169 
INJECTION-PUMP ASSEMBLY
FE6T
 
16713Z6204 
INJECTION-PUMP ASSEMBLY
FE6B
 
16713Z6205 
INJECTION-PUMP ASSEMBLY
FE6T
 
16713Z6206 
INJECTION-PUMP ASSEMBLY
FE6T
 
16713Z6207 
INJECTION-PUMP ASSEMBLY
FE6TA
 
16713Z6208 
INJECTION-PUMP ASSEMBLY
FE6T
101696-9080  

101696-9320 
 
16713Z6209 
INJECTION-PUMP ASSEMBLY
FE6T
9 400 616 136 
1671395210 
INJECTION-PUMP ASSEMBLY
NE6T
Back to top