101693-9421 ZEXEL INJECTION-PUMP ASSEMBLY Calibration Data 1016939421


101693-9421 INJECTION-PUMP ASSEMBLY
Rating:
36
Buy INJECTION-PUMP ASSEMBLY 101693-9421 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

ZEXEL 101693-9421 1016939421

Service parts 101693-9421 INJECTION-PUMP ASSEMBLY:

1. _
2. FUEL INJECTION PUMP 101069-9410
3. GOVERNOR 105931-3731
4. SUPPLY PUMP 105210-5290
5. AUTOM. ADVANCE MECHANIS 105643-0690
6. COUPLING PLATE
7. COUPLING PLATE
8. _
9. _
10. NOZZLE AND HOLDER ASSY 105101-6390
11. Nozzle and Holder
12. Open Pre:MPa(Kqf/cm2) 21.6{220}
13. NOZZLE-HOLDER 105031-3900
14. NOZZLE 105015-8810
15. NOZZLE SET

Include in #1:

101693-9421 as INJECTION-PUMP ASSEMBLY

Cross reference number

ZEXEL 101693-9421 1016939421


Zexel num
Bosch num
Firm num
Name
101693-9421 
 
  DPICO
INJECTION-PUMP ASSEMBLY
* Q

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil
  ISO4113 or {SAEJ967d}
Test oil temperature degC   40 40 45
Nozzle and nozzle holder   105780-8140
Bosch type code   EF8511/9A
Nozzle   105780-0000
Bosch type code   DN12SD12T
Nozzle holder   105780-2080
Bosch type code   EF8511/9
Opening pressure MPa   17.2
Opening pressure kgf/cm2   175
Injection pipe
Outer diameter - inner diameter - length (mm)
mm   6-2-600
Overflow valve   131424-5520
Overflow valve opening pressure kPa   255 221 289
Overflow valve opening pressure kgf/cm2   2.6 2.25 2.95
Tester oil delivery pressure kPa   157 157 157
Tester oil delivery pressure kgf/cm2   1.6 1.6 1.6
Direction of rotation (viewed from drive side)
Left
  L
Injection timing adjustment
Direction of rotation (viewed from drive side)
Left
  L
Injection order   1-5-3-6- 2-4
Pre-stroke mm   3.3 3.25 3.35
Beginning of injection position
Governor side
  NO.1
Difference between angles 1
Cal 1-5
deg.   60 59.5 60.5
Difference between angles 2
Cal 1-3
deg.   120 119.5 120.5
Difference between angles 3
Cal 1-6
deg.   180 179.5 180.5
Difference between angles 4
Cyl.1-2
deg.   240 239.5 240.5
Difference between angles 5
Cal 1-4
deg.   300 299.5 300.5
Injection quantity adjustment
Adjusting point   -
Rack position   10.55+-0 .5
Pump speed r/min   800 800 800
Each cylinder's injection qty mm3/st.   45 43.8 46.2
Basic   *
Fixing the rack   *
Standard for adjustment of the maximum variation between cylinders   *
Injection quantity adjustment_02
Adjusting point   H
Rack position   9.5+-0.5
Pump speed r/min   275 275 275
Each cylinder's injection qty mm3/st.   8.7 7.4 10
Fixing the rack   *
Standard for adjustment of the maximum variation between cylinders   *
Injection quantity adjustment_03
Adjusting point   A
Rack position   R1(10.55 )
Pump speed r/min   800 800 800
Average injection quantity mm3/st.   45 44 46
Basic   *
Fixing the lever   *
Injection quantity adjustment_04
Adjusting point   B
Rack position   (R1+0.3)
Pump speed r/min   1450 1450 1450
Average injection quantity mm3/st.   88 87 89
Fixing the lever   *
Injection quantity adjustment_05
Adjusting point   C
Rack position   R1+0.15
Pump speed r/min   655 655 655
Average injection quantity mm3/st.   41 37 45
Fixing the lever   *
Injection quantity adjustment_06
Adjusting point   I
Rack position   14.3+-0. 5
Pump speed r/min   100 100 100
Average injection quantity mm3/st.   73 63 83
Fixing the lever   *
Rack limit   *
Timer adjustment
Pump speed r/min   1250--
Advance angle deg.   0 0 0
Remarks
Start
 
Timer adjustment_02
Pump speed r/min   1200
Advance angle deg.   0.8
Timer adjustment_03
Pump speed r/min   1500
Advance angle deg.   5 4.5 5.5
Remarks
Finish
 

Test data Ex:

Governor adjustment

Test data 101693-9421
N:Pump speed R:Rack position (mm) (1)Torque cam stamping: T1 (2)Tolerance for racks not indicated: +-0.05mm. (3)RACK LIMIT
----------
T1=F53
----------

Speed control lever angle

Test data 101693-9421
F:Full speed I:Idle (1)Stopper bolt set position 'H'
----------

----------
a=18.5deg+-5deg b=(40deg)+-3deg

Stop lever angle

Test data 101693-9421
N:Engine manufacturer's normal use S:Stop the pump. (1)Set the stopper bolt at pump speed = aa and rack position = bb (non-injection rack position). Confirm non-injection. (2)After setting the stopper bolt, confirm non-injection at speed cc. Rack position = dd (non-injection rack position). (3)Rack position = approximately ee. (4)Free (at shipping)
----------
aa=1550r/min bb=(6.7)-0.5mm cc=275r/min dd=(8.3)mm ee=17.4mm
----------
a=(38.5deg)+-5deg b=(27deg) c=(17deg)+-5deg

0000001501 MICRO SWITCH

Adjustment of the micro-switch Adjust the bolt to obtain the following lever position when the micro-switch is ON. (1)Speed N1 (2)Rack position Ra
----------
N1=400r/min Ra=9.2+-0.1mm
----------

Timing setting

Test data 101693-9421
(1)Pump vertical direction (2)Position of timer's tooth at No 1 cylinder's beginning of injection (3)B.T.D.C.: aa (4)-
----------
aa=12deg
----------
a=(1deg)




Have questions with 101693-9421?





Group cross 101693-9421 ZEXEL

 
 
INJECTION-PUMP ASSEMBLY
F 019 Z10 840 
 
INJECTION-PUMP ASSEMBLY

Nissan-Diesel 

F 019 Z10 841 
16713Z5878 
INJECTION-PUMP ASSEMBLY
FE6T
 
 
INJECTION-PUMP ASSEMBLY

Nissan-Diesel 

F 019 Z10 842 
16713Z5879 
INJECTION-PUMP ASSEMBLY
FE6TA
 
 
INJECTION-PUMP ASSEMBLY

Dpico 

101693-9421  
 
 
INJECTION-PUMP ASSEMBLY
 
 

 
 
INJECTION-PUMP ASSEMBLY
 
 
INJECTION-PUMP ASSEMBLY

Nissan-Diesel 

9 400 610 793 
16713Z5904 
INJECTION-PUMP ASSEMBLY
FE6T
 
 
INJECTION-PUMP ASSEMBLY
 
 
INJECTION-PUMP ASSEMBLY

Nissan-Diesel 

F 019 Z10 843 
16713Z5905 
INJECTION-PUMP ASSEMBLY
FE6T
 
 
INJECTION-PUMP ASSEMBLY
 
 
INJECTION-PUMP ASSEMBLY

Nissan-Diesel 

 
16800Z5562 
INJECTION-PUMP ASSEMBLY
FE6T
 
 
INJECTION-PUMP ASSEMBLY
 
 
INJECTION-PUMP ASSEMBLY

Nissan-Diesel 

 
16800Z5563 
INJECTION-PUMP ASSEMBLY
FE6T
 
 
INJECTION-PUMP ASSEMBLY

Nissan-Diesel 

9 400 616 071 
16713Z5906 
INJECTION-PUMP ASSEMBLY
FE6TA
 
 
INJECTION-PUMP ASSEMBLY

Nissan-Diesel 

 
16713Z5907 
INJECTION-PUMP ASSEMBLY
FE6TA
Back to top