101691-4600 ZEXEL INJECTION-PUMP ASSEMBLY Calibration Data 1016914600 1156010700


101691-4600 INJECTION-PUMP ASSEMBLY
Rating:
16
Buy INJECTION-PUMP ASSEMBLY 101691-4600 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

ZEXEL 101691-4600 1016914600
ISUZU 1156010700 1156010700

Service parts 101691-4600 INJECTION-PUMP ASSEMBLY:

1. _
2. FUEL INJECTION PUMP 101069-3230
3. GOVERNOR 105472-0960
4. SUPPLY PUMP 105220-4531
5. AUTOM. ADVANCE MECHANIS 105612-0840
6. COUPLING PLATE 105662-0350
7. COUPLING PLATE
8. _
9. _
10. NOZZLE AND HOLDER ASSY 105101-2010
11. Nozzle and Holder 9-15300-184-2
12. Open Pre:MPa(Kqf/cm2) 9.8{100}
13. NOZZLE-HOLDER 105031-2600
14. NOZZLE 105000-1130
15. NOZZLE SET

Include in #1:

101691-4600 as INJECTION-PUMP ASSEMBLY

Include in #2:

Cross reference number

ZEXEL 101691-4600 1016914600
ISUZU 1156010700 1156010700


Zexel num
Bosch num
Firm num
Name
101691-4600 
 
1156010700  ISUZU
INJECTION-PUMP ASSEMBLY
DH100 * K

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil
  ISO4113 or {SAEJ967d}
Test oil temperature degC   40 40 45
Nozzle and nozzle holder   105780-8140
Bosch type code   EF8511/9A
Nozzle   105780-0000
Bosch type code   DN12SD12T
Nozzle holder   105780-2080
Bosch type code   EF8511/9
Opening pressure MPa   17.2
Opening pressure kgf/cm2   175
Injection pipe
Outer diameter - inner diameter - length (mm)
mm   6-2-600
Tester oil delivery pressure kPa   157 157 157
Tester oil delivery pressure kgf/cm2   1.6 1.6 1.6
Direction of rotation (viewed from drive side)
Right
  R
Injection timing adjustment
Direction of rotation (viewed from drive side)
Right
  R
Injection order   1-4-2-6- 3-5
Pre-stroke mm   2.2 2.15 2.25
Beginning of injection position
Drive side
  NO.1
Difference between angles 1
Cal 1-4
deg.   60 59.5 60.5
Difference between angles 2
Cyl.1-2
deg.   120 119.5 120.5
Difference between angles 3
Cal 1-6
deg.   180 179.5 180.5
Difference between angles 4
Cal 1-3
deg.   240 239.5 240.5
Difference between angles 5
Cal 1-5
deg.   300 299.5 300.5
Injection quantity adjustment
Adjusting point   A
Rack position   12.9
Pump speed r/min   600 600 600
Average injection quantity mm3/st.   106 103.7 108.3
Max. variation between cylinders %   0 -2 2
Basic   *
Fixing the lever   *
Injection quantity adjustment_02
Adjusting point   B
Rack position   12.5
Pump speed r/min   1000 1000 1000
Average injection quantity mm3/st.   109.5 106 113
Max. variation between cylinders %   0 -3 3
Fixing the lever   *
Injection quantity adjustment_03
Adjusting point   C
Rack position   6.5+-0.5
Pump speed r/min   225 225 225
Average injection quantity mm3/st.   10 7.7 12.3
Max. variation between cylinders %   0 -13 13
Fixing the rack   *
Timer adjustment
Pump speed r/min   400+-50
Advance angle deg.   0 0 0
Remarks
Start
 
Timer adjustment_02
Pump speed r/min   600
Advance angle deg.   0.6 0.1 1.1
Timer adjustment_03
Pump speed r/min   900
Advance angle deg.   1.4 0.9 1.9
Timer adjustment_04
Pump speed r/min   1150
Advance angle deg.   2 1.5 2.5
Remarks
Finish
 

Test data Ex:

Governor adjustment

Test data 101691-4600
N:Pump speed R:Rack position (mm) (1)Beginning of damper spring operation: DL (2)RACK LIMIT: RAL
----------
DL=6-0.2mm RAL=12.9+0.2mm
----------

0000000901

Test data 101691-4600
F:Full load I:Idle
----------

----------
a=42deg+-3deg b=44deg+-5deg

Stop lever angle

Test data 101691-4600
N:Pump normal S:Stop the pump.
----------

----------
a=35.5deg+-5deg b=71deg+-5deg

0000001501 MICRO SWITCH

Adjustment of the micro-switch Adjust the bolt to obtain the following lever position when the micro-switch is ON. (1)Speed N1 (2)Rack position Ra
----------
N1=375r/min Ra=6.5mm
----------




Have questions with 101691-4600?





Group cross 101691-4600 ZEXEL

Isuzu 

101691-4600  
 
1156010700 
INJECTION-PUMP ASSEMBLY
DH100
Back to top